Home > PROSELECT > PROSELECT PSTSN11AWH Non Programmable Thermostat Installation Guide

PROSELECT PSTSN11AWH Non Programmable Thermostat Installation Guide

Wiring conventional systems: forced air and  
hydronics  
1H/1C System (1 transformer)  
1H/1C System (2 transformers)  
R
Power [1]  
R
Power (heating transformer) [1]  
Rc [R+Rc joined by SliderTab] [2]  
Rc Power (cooling transformer) [1]  
Y
C
Compressor contactor  
24VAC common [3]  
Y
C
Compressor contactor  
24VAC common [3, 4]  
W
G
Heat  
Fan  
W
G
Heat  
Fan  
Heat-only System  
Power [1]  
Rc [R+Rc joined by SliderTab] [2]  
Heat-only System with Fan  
Power [1]  
Rc [R+Rc joined by SliderTab] [2]  
R
R
C
24VAC common [3]  
C
24VAC common [3]  
W
Heat  
W
G
Heat  
Fan  
Series 20 ZoneValve [5]  
Series 20 valve terminal “R” [1]  
Rc [R+Rc joined by SliderTab] [2]  
Cool-only System  
Power [1]  
Rc [R+Rc joined by SliderTab] [2]  
R
R
Y
C
W
Series 20 valve terminal “W”  
24VAC common [3]  
Series 20 valve terminal “B”  
Y
C
G
Compressor contactor  
24VAC common [3]  
Fan  
Heat-only System  
(power open zone valve) [5]  
R
Power [1]  
Rc [R+Rc joined by SliderTab] [2]  
W
C
Valve  
24VAC common [3]  
Wiring heat pump systems  
1H/1C Heat Pump System  
2H/1C Heat Pump System (PSTSN21AWH  
only)  
R
Power [1]  
R
Power [1]  
Rc [R+Rc joined by SliderTab] [2]  
Rc [R+Rc joined by SliderTab] [2]  
Y
C
Compressor contactor  
24VAC common [3]  
Y
C
Compressor contactor  
24VAC common [3]  
O/B Changeover valve [6]  
O/B Changeover valve [6]  
Fan  
AUX Auxiliary heat  
G
W
Fan  
G
Do not use this terminal for heat  
pump applications!  
E
W
Emergency heat  
Do not use this terminal for heat  
pump applications!  
NOTES  
Wire specifications: Use 18- to 22-gauge thermostat wire. Shielded cable is not required.  
[1] Power supply. Provide disconnect means and over-  
former.  
load protection as required.  
[5] In ISU set Heat system type to Radiant Heat. Set  
[2] Move R-SliderTab on the base plate to the R set-  
ting. For more information, see “Setting slider tabs”  
number of cool stages to 0.  
[6] In Installer Setup, set changeover valve to O (for  
cool changeover) or B (for heat changeover).  
[3] Optional 24VAC common connection.  
[4] Common connection must come from cooling trans-  
4
 
Thermostat mounting  
1. Push excess wire back into the wall  
opening.  
2. Close the base plate door. It should  
remain closed without bulging.  
3. Align the base plate with the thermostat,  
and push gently until the thermostat  
snaps in place.  
4. Turn the power on at the breaker box or  
switch.  
M39419  
System operation settings  
1. Press Menu, and then press the Mode  
(+) button to cycle to the next available  
System mode.  
2. Cycle through the modes until the desired  
System mode is displayed, and then press  
Done.  
NOTE: Available System modes vary by  
model and system settings.  
System modes:  
Auto:Thermostat selects heating or cooling as needed.  
Heat:Thermostat controls only the heating system.  
Cool:Thermostat controls only the cooling system.  
Em heat (PSTSN21AWH only): For heat pumps with auxiliary heat.  
Thermostat controls auxiliary heat. Compressor is not used.  
Off: Heating and cooling system is off. Fan will still operate if fan is set to  
On.  
NOTE: Heat On/Cool On may flash for 5 minutes due to compressor protection.  
Fan operation settings  
1. Press Menu, and then press the  
Fan (-) button to cycle to the next  
available Fan mode.  
2. Cycle through the modes until the  
desired Fan mode is displayed, then  
press Done.  
NOTE: Available Fan modes vary with  
system settings.  
Fan modes:  
Auto: Fan runs only when the  
heating or cooling system is on.  
On: Fan is always on.  
5
 
GeneralDetails
NamePROSELECT PSTSN11AWH Non Programmable Thermostat Installation Guide
MakePROSELECT
LanguageEnglish
FiletypePDF (Download)
File size2.37 MB
Download PDF
1 Star2 Stars3 Stars4 Stars5 Stars (1 votes, average: 5.00 out of 5)
Loading...

PROSELECT PSTSN11AWH Non Programmable Thermostat Installation Guide