Honeywell TL5110 Digital Non-programmable Thermostat User Guide

1

2

TL5110  

User Guide  

Digital Non-programmable Thermostat  

5.  

Troubleshooting  

Heating power  

indicator  

r

Temperature  

display  

PROBLEM  

SOLUTIONS  

This is normal. Under normal operation, the  

thermostat housing can reach a temperature  

between 35 °C (95 °F) and 40 °C (104 °F).  

Thermostat is hot.  

Temperature  

adjustment  

buttons  

Correct if any the following conditions applies:  

•

•

The thermostat is exposed to air draft.  

The sticker on the thermostat’s screen has  

not been removed.  

Displayed tempera-  

ture is wrong.  

•

The thermostat is located near or above a  

heat source such as a light dimmer.  

The thermal protection device on the heater has  

temporarily opened. This can happen if the  

heater is obstructed by furniture or curtain and  

has overheated, or if the heater’s thermal pro-  

tection device is too sensitive.  

1.  

Display disappears  

and reappears after  

a few minutes.  

Description  

n

This thermostat can be used to control an electric heating system  

such as a baseboard heater, a radiant ceiling, a radiant floor, a con-  

vector, etc.  

6.  

Warranty  

2.  

;

Temperature Display and Setting  

The thermostat normally displays the actual (ambi-  

Honeywell warrants this product, excluding battery, to be free from defects in the  

workmanship or materials, under normal use and service, for a period of five (5)  

years from the date of purchase by the consumer. If at any time during the warranty  

period the product is determined to be defective or malfunctions, Honeywell shall  

repair or replace it (at Honeywell's option).  

o

ent) temperature.  

•

To view the setpoint temperature, press once on  

either of the temperature adjustment buttons.  

If the product is defective,  

(i)  

return it, with a bill of sale or other dated proof of purchase, to the place from  

which you purchased it, or  

The icon  

appears during the setpoint display.  

(ii) call Honeywell Customer Care at 1-800-468-1502. Customer Care will make  

the determination whether the product should be returned to the following  

address: Honeywell Return Goods, Dock 4 MN10-3860, 1885 Douglas Dr N,  

Golden Valley, MN 55422, or whether a replacement product can be sent to  

you.  

•

To change the setpoint temperature, press the appropriate but-  

ton until the desired value is displayed.  

3.  

Power Outage  

During a power outage, the setpoint is stored in memory.  

This warranty does not cover removal or reinstallation costs. This warranty shall  

not apply if it is shown by Honeywell that the defect or malfunction was caused by  

damage which occurred while the product was in the possession of a consumer.  

Honeywell's sole responsibility shall be to repair or replace the product within the  

terms stated above. HONEYWELL SHALL NOT BE LIABLE FOR ANY LOSS OR  

DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL  

DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF  

ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS  

PRODUCT. Some states do not allow the exclusion or limitation of incidental or  

consequential damages, so this limitation may not apply to you.  

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES  

ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES,  

INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  

PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE FIVE-YEAR DURATION  

OF THIS WARRANTY. Some states do not allow limitations on how long an implied  

warranty lasts, so the above limitation may not apply to you.  

p

4.  

Specifications  

- Supply: 120/240 VAC, 50/60 Hz  

q

- Minimum load: 2 A (resistive only)  

500 W @ 240 VAC  

250 W @ 120 VAC  

- Maximum load: 12.5 A (resistive only)  

3000 W @ 240 VAC  

1500 W @ 120 VAC  

This warranty gives you specific legal rights, and you may have other rights which  

vary from state to state.  

If you have any questions concerning this warranty, please write Honeywell Cus-  

tomer Relations, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-468-  

1502. In Canada, write Retail Products ON15-02H, Honeywell Limited/Honeywell  

Limitée, 35 Dynamic Drive, Scarborough, Ontario M1V4Z9.  

- Display range: 0 to 50°C (32 to 122°F)  

- Setpoint range: 5 to 30°C (40 to 85°F)  

- Storage: -20 to 50°C (-4 to 120°F)  

- Approval: c UL us  

7.  

Customer assistance  

If you have any questions about the operation of your thermostat,  

please go to http://yourhome.honeywell.com, or call Honeywell  

Customer Care toll-free at 1-800-468-1502.  

ꢀ

TL5110  

69-1966EF  

6/21/06  

1/1  

firealarmresources.com  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	Honeywell TL5110 Digital Non-programmable Thermostat User Guide
Make	Honeywell
Language	English
Filetype	PDF (Download)
File size	0.16 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• Honeywell

Honeywell TL5110 Digital Non-programmable Thermostat User Guide Overview

Summary of Contents

• Page 1: User guide for the digital non-programmable thermostat includes troubleshooting information. The thermostat can reach temperatures between 35 °C (95 °F) and 40 °C (104 °F) during normal operation. If the thermostat is hot, check for air drafts or if the sticker on the screen has been removed. Displayed temperature may be incorrect if the thermostat is near a heat source or if the thermal protection device has opened. During a power outage, the setpoint is stored in memory. Honeywell warrants the product to be free from defects for five years from the date of purchase. If the product is defective, it can be returned with proof of purchase for repair or replacement. The warranty does not cover removal or reinstallation costs and is limited to five years. Specifications include supply voltage, minimum and maximum load, and display range. For customer assistance, visit the Honeywell website or contact customer care.
• Page 2: Guide de l’utilisateur Thermostat non programmable Problèmes et solutions Le thermostat est chaud. Ceci est normal. En fonctionnement normal, le boîtier du thermostat peut atteindre une température entre 35 °C (95 °F) et 40 °C (104 °F). Corriger si l’une des conditions suivantes existe : Il y a un courant d’air à proximité. L’autocollant sur l’écran du thermostat n’a pas été enlevé. La température affichée est erronée. Le thermostat est situé près ou au-dessus d’une source de chaleur tel qu’un gradateur de lumière. Ce thermostat peut servir à réguler un appareil de chauffage électrique tel qu’une plinthe chauffante, un plafond radiant, un plancher chauffant, un convecteur, etc. Garantie Honeywell garantit ce produit, à l'exception des piles, contre tout vice de fabrication ou de matière pour cinq (5) ans à partir de la date d'achat par le consommateur. La présente garantie ne couvre pas les frais de retrait ou de réinstallation. Durant une panne de courant, la température de consigne est sauvegardée. Vous n’auriez donc pas à régler la température après la panne. Fiche technique Alimentation : 120/240 VCA, 50/60 Hz Charge maximale : 12,5 A (résistive seulement) Plage d’affichage : 0 à 50°C (32 à 122°F) Service à la clientèle Si vous avez des questions sur le fonctionnement de votre thermostat, veuillez consulter le site de Honeywell.