Honeywell T7350 Programmable Thermostat Owner’s Manual
NOTE: The thermostat must be in program
mode to use the copy feature. If the
thermostat is already in program
mode, skip step 1.
Setting Schedule Times
Use the keys in the “Schedule” area of the
keypad for this procedure.
1. Press Occupied.
1. Press Occupied.
2. Press Day to select the day to be copied.
3. Press Copy.
4. Press Copy again.
NOTE: Anytime a start time is not
required, press Clear Start Time.
5. Press Day until the day to receive the
copy is displayed.
6. Press Copy.
2. Press Day until desired day is displayed.
3. Press Occupied or Not Occupied until the
proper period is displayed.
4. Press up s or down t until the desired start
time is displayed.
5. Repeat steps 3 and 4 for a given day.
NOTE: DONE displays for two seconds
then the program display
reappears.
6. Repeat steps 2 through 5 until finished.
7. Repeat steps 2 through 6 for all the days
desired.
8. Press Run Schedule.
Copying a Day
Use the keys in the “Schedule” area of the
keypad for this procedure.
63-2638
8
NOTES: The ranges mentioned can be limited
based upon setpoints and stops:
1. The greater of the Minimum Heat
Stop and the Not Occupied Heat set-
points determines the lowest setting
to which the occupied heat setpoint
can be adjusted: Stop/NotOcc ≤
Clearing Program Start Times
1. Press Occupied or Not Occupied until the
start period to be cleared is displayed.
2. Press Day until desired day is displayed.
3. Press Clear Start Time.
4. Repeat steps 1 through 3 for all the start
times to be cleared.
5. Press Run Schedule.
OccHeat ≤ (OccCool - 2).
2.
The lesser of Maximum Cool Stop
and Not Occupied Cool setpoints
determines the highest setting to
which the occupied cool setpoint
can be adjusted: Stop/NotOcc ≥
OccCool ≥ (OccHeat + 2).
Temperature Setpoints
Setpoint Limits
The setpoint temperature range is 40°F to 90°F
(4°C to 32°C) for heating and 45°F to 99°F
(7°C to 37°C) for cooling.
3.
4.
The Maximum Occupied Heat Set-
point is limited by Occupied Cool
Setpoint – 2.
The Minimum Occupied Cool Set-
point is limited by the Occupied
Heat Setpoint + 2.
9
63-2638
Programming Temperature Setpoints
Temperature Setpoint Overrides
1. Press Occupied Heat.
IMPORTANT
2. Press up ! or down " until the desired
temperature is displayed.
3. Press Occupied Cool.
— Setup determines Occupied override
duration.
— Default duration is three hours.
4. Press up ! or down " until the desired
temperature is displayed.
NOTE: To cancel Override and immediately
return to the program, press Run
Schedule.
5. Press Not Occupied Heat.
6. Press up ! or down " until the desired
temperature is displayed.
7. Press Not Occupied Cool.
8. Press up ! or down " until the desired
temperature is displayed.
T7770 Setpoint Knob
A T7770 setpoint knob can remotely adjust the
T7350 setpoint. This adjustment can be made
when the sensor is in override.
9. Press Run Schedule.
63-2638
10
NOTES:
—
2. To select a temperature setting other than
the default, press up ! or down " until
desired temperature offset displays
(range is 0°F to 3°F).
During override, only occupied and
standby heat setpoints, and cool
setpoints are adjusted.
—
—
The maximum adjustment is ±5°F.
With a disconnected or failed
T7770, or a T7350 set for local
temperature sensing, offset is zero.
Using Temporary Not Occupied Override
The Temporary Not Occupied Override fixes the
device to operate in Not Occupied mode for a
number of days (between 1 and 99) without
changing the programming saved in memory.
Using Temporary Occupied Override
The Temporary Occupied Override can be used
when the T7350 is in Not Occupied or Standby
mode. It switches to the Occupied mode for a
fixed number of hours.
NOTES:
—
If the number of days is set to zero,
no temporary change takes effect.
If the number of days is set just
below zero, the display for days is
“---” (an indefinite override).
—
1. To use the default occupied override,
press Temporary Occupied.
—
To turn off this override, you must
press Run Schedule.
NOTE: The default temperature setting
is the Occupied setpoint.
11
63-2638
1. Press Temporary Not Occupied.
2. Press up ! or down " to change the
duration of the Not Occupied period (in
days).
Changing Temperature Setpoint
Until Next Program Period
1. Press up s or down t until the desired tem-
perature is displayed.
NOTE: The default temperature setting
is the Not Occupied setpoint.
2. The temporary temperature appears for
approximately ten seconds, then the
room temperature is displayed.
3. Press
to display the default setpoint.
NOTE: The only way to change this set-
point is to change the Not Occu-
pied setpoint.
By using this Honeywell literature, you agree that Honeywell will have no liability for any damages
arising out of your use or modification to, the literature. You will defend and indemnify Honeywell, its
affiliates and subsidiaries, from and against any liability, cost, or damages, including attorneys’ fees,
arising out of, or resulting from, any modification to the literature by you.
63-2638 04-06
| General | Details |
|---|---|
| Name | Honeywell T7350 Programmable Thermostat Owner’s Manual |
| Make | Honeywell |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.25 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Honeywell T6 Pro Programmable Thermostat User Manual
Honeywell D1-528 Direct Thermostat Installation Guide
Honeywell FocusPRO P200 Programmable Thermostat User Guide
Honeywell RCHT8610WF Series Smart Thermostat Installation Guide
Honeywell T9 Smart Thermostat Installation Guide
Honeywell TH2320WF4011 FocusPRO Smart S200 Series Thermostat User Guide
Honeywell TL116A Thermostat Installation Guide
T10 Pro Smart Thermostat with Redlink Room Sensor
Honeywell TH6320WF2003 Lyric T6 Pro Wi-Fi Programmable Thermostat User Guide
Honeywell RTH9580 Wi-Fi Color Touchscreen Programmable Thermostat User Guide
bryant Smart Thermostat User Guide
Hunter 44110 Set And Save Programmable Thermostat Owner’s Manual
Zehnder ComfoControl Ease Installation Guide
VIVE COMFORT TP-N-721 Non Programmable Thermostat Instruction Manual
EUROTRONIC SPIRIT ZigBee Energy Saving Thermostat User Guide
GENERALLIFE FH254 Underfloor Heating Thermostat User Manual
White Rodgers BP150 Line Voltage Programmable Thermostat User Guide
Network Thermostat X7-Series Thermostat Installation Guide
ideal HEATING HALO LITE Room Thermostat User Guide
beok BOT-323W Room Thermostat Instruction Manual