Honeywell RLV450 Programmable Thermostat User Guide

1

2

3

4

5

6

7

8

RLV450  

PROGRAMMABLE THERMOSTAT  

USER GUIDE  

READ BEFORE INSTALLING  

DESCRIPTION  

INSTALLATION  

Temperature pre-  

set buttons  

WARNING  

TURN OFF POWER TO THE HEATING SYSTEM AT THE MAIN  

POWER PANEL TO AVOID ELECTRICAL SHOCK. THE  

INSTALLATION MUST BE PERFORMED BY AN ELECTRICIAN.  

All cables and connections must conform to the local electrical  

code.  

Indicates that the tem-  

perature setpoint is dis-  

played  

Indicates that the set-  

tings are locked  

Time and day  

Special CO/ALR solderless connectors must be used when  

connecting with aluminum conductors.  

Install the thermostat onto an electrical box.  

Install the thermostat about 5 feet high, on an inside wall facing the  

heater.  

Avoid locations where there are air drafts (such as the top of a  

staircase or an air outlet), dead air spots (such as behind a door),  

or direct sunlight.  

Do not install the thermostat on a wall that conceals chimney or  

stove pipes.  

Set the hour  

Set the minute  

Temperature  

Indicates the current  

mode of operation  

Set the day  

Program the schedule  

Temperature pre-  

set icon  

Skip a period  

Indicates that the  

thermostat is configured  

for a fan-forced heater  

Select the mode of  

operation  

Indicates the  

heating power  

The thermostat wires are not polarized; either wire can be  

connected to the load or to the power supply.  

Indicates the current  

period (appears in auto-  

matic mode only)  

Temperature  

adjustment but-  

tons  

NOTE:  

Always keep the thermostat's vents clean and unobstructed.  

Indicates that the thermostat  

is without power *  

1.  

* LP appears only for the first two minutes when the thermostat is without  

power. This can occur during a power outage or when the thermal protection  

device inside the baseboard heater is opened.  

Fig. 1.  

This programmable thermostat can be used to control an electric heating  

system such as an electric baseboard heater, a radiant ceiling, a radiant floor,  

a convector or a fan-forced heater.  

The thermostat cannot be used with:  

•

•

•

•

a resistive load over 16.7 A  

a resistive load under 2 A  

a system driven by a contactor or relay (inductive load)  

a central heating system  

M38000  

SUPPLIED PARTS:  

•

•

•

One (1) thermostat  

Two (2) 6-32 screws  

Two (2) solderless connectors  

Fig. 2.  

69-2201ES-08  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	Honeywell RLV450 Programmable Thermostat User Guide
Make	Honeywell
Language	English
Filetype	PDF (Download)
File size	0.56 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• Honeywell

Honeywell RLV450 Programmable Thermostat User Guide Overview

Summary of Contents

• Page 1: RLV450 programmable thermostat user guide Read before installing Installation must be performed by an electrician. Turn off power to the heating system at the main power panel to avoid electrical shock. All cables and connections must conform to the local electrical code. Install the thermostat about 5 feet high, on an inside wall facing the heater. Avoid locations with air drafts, dead air spots, or direct sunlight. The thermostat can control an electric heating system such as an electric baseboard heater or a fan-forced heater. The thermostat cannot be used with a resistive load over 16.7 A or under 2 A. Special CO/ALR solderless connectors must be used when connecting with aluminum conductors. Always keep the thermostat's vents clean and unobstructed.
• Page 2: Connect the thermostat wires to the line wires and to the load wires using solderless connectors for copper wires. Early Start can be used in Automatic mode only. When this function is enabled, the thermostat calculates the optimal time to start heating to obtain the desired temperature by the set time. Select 15-second cycles in most cases as it provides better temperature control. However, you must select 15-minute cycles if you have a fan-forced heater. The settings are locked. The temperature adjustment buttons only allow you to view the temperature setpoint. The thermostat can automatically re-adjust its clock at Daylight Savings Time changeover. The function is disabled (default setting) when the clock loses its setting. The configuration switches are on the back of the thermostat. The factory settings are indicated by the gray cells in the following table. The thermostat normally displays the actual temperature. To view the setpoint, press the V or W button briefly. To change the setpoint, press the V or W button until the desired temperature is displayed.
• Page 3: The thermostat has 3 preset temperatures: Comfort, Economy, and Vacation. Comfort temperature is used during periods 1 and 3, while Economy temperature is used during periods 2 and 4. You can have a different program for each day of the week. To use the Comfort or Economy temperature, press the corresponding button. To store the Comfort or Economy temperature, press and hold the appropriate button for approximately 3 seconds. To modify the schedule, access the programming mode and select the day to program. Automatic mode sets the temperature according to the programmed schedule. Temporary Bypass allows modification of the setpoint until the end of the current period. During a power outage, settings are stored in memory, but the thermostat’s clock must be re-adjusted if the outage exceeds 4 hours. Manual mode requires the temperature to be set manually, without using the programmed schedule.
• Page 4: Solutions The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The correct disposal of end-of-life equipment will help prevent negative consequences for the environment and human health. Resideo warrants this product, excluding battery, to be free from defects in workmanship or materials, under normal use and service, for a period of one year from the date of first purchase by the original purchaser. If the product is defective, return it with a bill of sale or other dated proof of purchase. This warranty does not cover removal or reinstallation costs. Resideo’s sole responsibility shall be to repair or replace the product within the terms stated above. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. If you have any questions about the operation of your thermostat, please contact customer assistance. Approval: CSA / UL
• Page 5: RLV450 Termostato programable Guía del usuario Leer antes de instalar Descripción Instalación Advertencia Cortar la alimentación del sistema de calefacción en el panel de alimentación principal para evitar riesgos de electrocución. La instalación debe hacerla un electricista. El termostato debe instalarse a alrededor de 1,5 m (5 pies) del piso, en una pared interior frente al aparato de calefacción. No debe instalarse el termostato en una pared que oculte conductos de chimeneas o estufas. Este termostato programable puede usarse para controlar un sistema de calefacción eléctrico, tal como una estufa eléctrica de zócalo, un cielorraso radiante, un piso calefaccionado, un convector eléctrico o un calefactor a aire forzado.
• Page 6: Conectar los cables del termostato a la alimentación y a la carga por medio de conectores sin soldadura para cables de cobre. El encendido anticipado puede usarse en modo automático solamente. Cuando esta función está activada, el termostato calcula el momento óptimo de encendido de la calefacción para obtener la temperatura deseada a la hora establecida. En la mayoría de los casos se deben seleccionar ciclos de 15 segundos, porque permiten un mejor control de la temperatura. Los ajustes están bloqueados. Los botones de ajuste de la temperatura sólo permiten ver el punto de ajuste de la temperatura. El termostato puede reajustar la hora automáticamente cuando hay que hacer el cambio a la hora de verano. Esta función está desactivada por defecto cuando se pierde el ajuste de la hora. Los conmutadores de configuración están en la parte posterior del termostato. El termostato indica normalmente la temperatura del momento. Para cambiar el punto de ajuste, presionar los botones V o W hasta que aparezca la temperatura deseada.
• Page 7: Uso de la temperatura predefinida. La temperatura de Confort se usa en los períodos 1 y 3 y la temperatura de Economía en los períodos 2 y 4. El termostato tiene 3 temperaturas predefinidas: Temperatura de Confort, Temperatura de Economía, Temperatura de Vacaciones. Se puede tener un programa diferente para cada día de la semana. Para usar la temperatura Confort o Economía, presionar el botón correspondiente. Para modificar el horario, presionar Pgm para acceder al modo de programación. En caso de corte de corriente, los ajustes están salvaguardados en la memoria. El horario consiste en 4 períodos por día, que representan un día de semana típico. El termostato puede estar en modo automático, cancelación temporaria o manual. La temperatura medida puede aparecer como LO o HI si está fuera del margen de visualización del termostato.
• Page 8: Instromet Mexicana S. de R.L. de C.V. garantiza que este producto está libre de defectos en su mano de obra y materiales contra cualquier defecto de fabricación y funcionamiento, bajo uso normal, por el término de 1 año a partir de la fecha de la compra por el consumidor. Si se determina que el producto está defectuoso, Instromet deberá reparar o reemplazar el producto bajo ciertas condiciones. La pantalla aparece pálida cuando la calefacción está activada. El rendimiento del termostato es reducido debido a un error del sensor. Esta garantía no cubre gastos de mano de obra por re-instalación. La única responsabilidad de Instromet será reparar o reemplazar el producto dentro de los términos establecidos. Esta garantía es la única garantía expresa que Instromet ofrece respecto de este producto. La duración de cualquier garantía implícita se limita a la duración de un año de esta garantía. El producto no es válido si ha sido utilizado en condiciones distintas a las normales. Este aparato digital de clase B cumple con la normativa canadiense ICES-003.