heatit Z-TRM3 WiFi Thermostat Instruction Manual
5. INSTALLATION
Note! The top cover has to be installed when the thermostat
is connected to the main power source. The thermostat is not
a SELV product. All voltage parts must be considered to be
230VAC.
Installation must be done by a qualified electrician in accordance with
the National Building codes. Before installation, disconnect the power
to the device from the mains. During installation of the device, power
to the device must be disconnected AT ALL TIMES!
6. ADD/REMOVE
51.1mm
15.6mm
Please read this before installation
49.5mm
21.3mm
The primary controller/gateway has a mode for adding or removing
devices. Please refer to your primary controller manual on how to set
the primary controller in add/remove mode. The device may only be
added or removed from the network if the primary controller is in add/
remove mode. When the device is removed from the network, it will
NOT revert to factory settings.
There are two ways to add the device to a Z-Wave network.
6.1 Method 1: Standard (Manual)
1. Press Center (confirm) for 10 seconds. The display will show OFF.
2. Press Right (down) 5 times until you see Con on the display.
3. Start the add/remove device process in your primary controller.
4. Start the add/remove mode by pressing Center (confirm) for
approximately 2 seconds.
5.1 Controls
Use e.g. a small slotted screwdriver. Start by carefully removing the
front cover by pushing the release springs. The front cover and the
frame may now be removed.
Adding/removing mode is indicated on the display by rotating
LED segments on the display. This lasts until the timeout occurs
after 90 seconds, or until the module has been added/removed in
the network. Confirmation will show Inc/EcL on the display. Exit
programming mode by choosing ESC in the menu. Your thermostat
is now ready for use with default settings.
58.8mm
Release spring
NB! When the thermostat is removed from the gateway, the
parameters are not reset. To reset the parameters, see Chapter 7:
”Factory reset”. If adding/removing fails, Err (error) will appear.
Please perform a ”remove device”process and try again. If Err displays
again, please see Chapter 7: “Factory reset”.
6.2 Method 2: SmartStart (Automatic)
SmartStart enabled products may be added to a Z-Wave network
by scanning the Z-Wave QR-Code on the product if your primary
controller supports SmartStart inclusion. No further action is required
and the SmartStart product will be added automatically after being
powered on within range of the primary controller.
1: Left
2: Center
87mm
3: Right
Connect the wires to the thermostat terminals:
Use 1.5mm² or 2.5mm² according to load.
The Z-Wave QR-Code locations may be found in Chapter 20
”Z-Wave QR-Code/DSK”.
HEATING (N)
Heating cable connection (Neutral)
N
Power connection (Neutral) 230VAC
Power connection (Live) 230VAC
Heating cable connection
7. FACTORY RESET
L
By pressing buttons Right and Center (down and confirm) for 20 seconds, the
thermostat will perform a complete factory reset. The device will display rES for
10 seconds while performing a factory reset. When rES no longer is displayed,
the thermostat has been reset.
HEATING (L)
FLOOR SENSOR
NTC type (10, 12, 15, 22, 33 or 47kΩ)
Default 10kΩ
EXTERNAL SENSOR NTC type (10, 12, 15, 22, 33 or 47kΩ)
Default 10kΩ
NB! Please use this procedure only when the primary controller/
gateway is missing or otherwise inoperable.
Next, position the thermostat and mount it into the wall flush box
using 2-4 screws. Position the frame over the flush box, then position
and carefully press the front cover until it snaps in place. Check that
the front cover has snapped in place properly on both sides. The front
cover should now fit firmly on all sides. In order to read the Power
Metering, the load needs to be connected to both heating L + N.
7.1 Startup
After powering up the device for the first time, all the parameters will have
default settings.
| General | Details |
|---|---|
| Name | heatit Z-TRM3 WiFi Thermostat Instruction Manual |
| Make | HEATIT |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.19 MB |
(1 votes, average: 5.00 out of 5)
Loading...
heatit Z-TRM6 DC Z Wave Electronic Thermostat Instruction Manual
HEATIT Z-TRM3 Thermostat User Guide
Heatit Z-TEMP2 Thermostat Installation Guide
HEATIT Z-Temp3 is a Battery Operated Thermostat Instruction Manual
4512673 Heatit ZM Thermostat 16A User Guide
HEATIT Z-TRM6 Matt Z-Wave Thermostat User Guide
HEATIT 54 304 59 DIN Smart Thermostat Installation Guide
HEATIT 54 305 41 WiFi6 Thermostat Installation Guide
HEATIT Z-TEMP3 Thermostat User Guide
heatit ET-7AW Touchscreen Programmable Thermostat User Manual
HEIL TSTATIIEWF-01 Smart Thermostat Owner’s Manual
GENERAL LIFE HT220S RF Digital Room Thermostat User Manual
Honeywell ATP921R3100 Evohome WiFi Connected Thermostat User Guide
GENERAL Life FH254S Underfloor Heating Thermostat User Manual
GENERAL 270 RF Room Thermostat Instruction Manual
STELPRO STF362NP Floor Heating Thermostat Owner’s Manual
Honeywell TH1100DV PRO Series Non Programmable Thermostat Instruction Manual
Milesight WT201 Airteq Smart Thermostat User Guide
Moes BHT-006 Series Thermostat User Manual
Hotwire HWTH Horizontal Thermostat Instructions