HEATIT 54 304 59 DIN Smart Thermostat Installation Guide
34.ASSOCIATION GROUPS
Without Multi Channel support:
SHORT
DESCRIPTION / COMMENT
DESCRIPTION
OF VALUE
NAME
Enabled, buttons on the
front of the device work.
(Default)
Disable buttons, must be en-
abled through the parameter,
or turned back on locally by
holding the center and right
button for 30 seconds until the
display shows “UNLK”.
MULTI LEVEL SWITCH DEVICE
DESCRIPTION
0
Lifeline.
Disable
buttons
1
1
1
0
0
Lifeline Group to be used by primary controller, sends:
-Thermostat Mode Report
-Thermostat Setpoint Report
-Thermostat Operating State Report
-Protection Report
Disabled, buttons on the
front of the device are
disabled.
1
0
1
F, Floor sensor (Default)
A2, External sensor
-Notification Report
-Meter Report
Sensor
mode
(OPER)
Choose which sensor mode
the device should operate
with.
Group 1
A2F, External sensor with
floor sensor limitations
2
2
-Sensor Multilevel Report
-Device Reset Locally Notification
-Indicator Report
PWER, Power regulator
mode
3
-Configuration Report
0
1
10KΩ (Default)
12KΩ
Max nodes in group: 1
2
3
4
5
6
7
15KΩ
Binary Switch Set.
Send Binary Switch set commands based on the internal relay state, sends:
-Binary Switch Set
22KΩ
Sensor
value (SEN)
Select the resistance value of
the connected NTC.
3
1
0
33KΩ
Group 2
Group 3
47KΩ
Max nodes in group: 10
6.8KΩ
Thermostat Setpoint set.
100KΩ
Sends Thermostat Setpoint set commands based on own setpoint to allow for
use as master thermostat, sends:
-Thermostat Setpoint Set
Floor
sensor
Devices the lowest tempera-
ture allowed by the thermostat
when using sensor mode
F, A2F.
4
5
6
7
2
2
2
2
minimum
tempera-
ture limit
20
20
20
20
400
400
400
400
20
20
2°C to 40°C (Default is 2°C)
2°C to 40°C (Default is 2°C)
Max nodes in group: 10
Thermostat Mode set.
External
sensor
Sends Thermostat Mode set commands based on own mode to allow for use as
master thermostat, sends:
-Thermostat Mode Set
Decides the lowest tempera-
ture allowed by the thermostat
when using sensor mode A2.
minimum
tempera-
ture limit
Group 4
Max nodes in group: 10
Floor
sensor
Decide the highest tempera-
ture allowed by the thermostat
when using sensor mode
F, A2F.
2°C to 40°C
(Default is 27°C)
maximum
tempera-
ture limit
270
400
With Multi Channel support:
External
sensor
Decide the highest tempera-
ture allowed by the thermostat
when using sensor mode A2.
1: THERMOSTAT DEVICE
THE MAIN THERMOSTAT DEVICE
2°C to 40°C
(Default is 40°C)
maximum
tempera-
ture limit
Lifeline.
Lifeline Group to be used by primary controller, sends:
-Thermostat Mode Report
-Thermostat Setpoint Report
-Thermostat Operating State Report
-Protection Report
-6.0°C to 6.0°C
Calibrates the sensor by
6°C. (Default is 0°C)
Floor
sensor
calibration
(CAF)
Manually calibrate sensor
F
8
1
-60
60
0
6°C.
-Notification Report
-Meter Report
NB! To set a negative value,
use 256 and subtract the
desired value.
Group 1
-Sensor Multilevel Report
-Device Reset Locally Notification
-Indicator Report
-6.0°C to 6.0°C.
Calibrates the sensor by
6°C. (Default is 0°C)
-Configuration Report
External
sensor
Manually calibrate sensor
A2 6°C.
9
1
-60
0
60
0
Max nodes in group: 1
calibration
(CAE)
NB! To set a negative value,
use 256 and subtract the
desired value.
Binary Switch Set
Send Binary Switch set commands based on the internal relay state, sends:
-Binary Switch Set
Group 2
Group 3
Regulation
mode
(REG)
Hysteresis (default)
PWM regulation
Choose between regulation
modes PWM and Hysteresis.
10
11
1
1
0
5
Max. nodes in group: 10
1
Thermostat Setpoint Set
Tempera-
ture control
hysteresis
(HYST)
Sends Thermostat Setpoint set commands based on own setpoint to allow for
use as master thermostat, sends:
-Thermostat Setpoint Set
Choose the hysteresis used
when regulation mode is set
to HYST.
0.3°C to 3.0°C.
Default is 5 (0.5°C)
3
30
Display setpoint
temperature. (Default)
Max. nodes in group: 10
0
Tempera- Select what is shown on the
ture display display during Standby state.
Thermostat Mode Set.
12
13
14
1
1
1
0
10
5
Display measured
temperature.
Sends Thermostat Mode set commands based on own mode to allow for use as
master thermostat, sends:
-Thermostat Mode Set
1
Group 4
Active
display
brightness
(BR1)
Configure the brightness of the
display during active state.
1
1
10
10 to 100% (Default 100%)
10 to 100% (Default 50%)
Max. nodes in group: 10
2: MULTILEVEL SENSOR DEVICE EXTERNAL SENSOR
Standby
display
Lifeline.
Lifeline Group for external sensor, sends:
-Sensor Multilevel Report
Configure the brightness of the
display during standby state.
10
brightness
(BR2)
Group 1
Tempera-
ture report
interval
Set the time interval between
consecutive temperature
reports.
30 to 65535 seconds.
845s (14 min) (Default)
0.1°C to 10°C
Max. nodes in group: 0
15
16
17
2
1
30
1
65535 845
3: MULTILEVEL SENSOR DEVICE TEMPERATURE SENSOR
Tempera-
ture report
hysteresis
Set the change in temperature
required to send a temperature
report based on change.
Lifeline.
Lifeline Group for floor sensor, sends:
-Sensor Multilevel Report
100
10
10 (1°C) (Default)
Group 1
Meter
report
interval
30 to 65535 seconds.
845s (14 min) (Default)
Set the time interval between
consecutive meter reports.
2
30
65535 845
Max. nodes in group: 0
0, device will turn off
and show an error in the
display. (Default)
0
Decide how the device should
Action after react when the overload /
35.CONFIGURATION PARAMETERS
18
2
1200
10 to 65535 seconds, de-
vice will attempt to turn on
again after an error based
on the delay specified.
error
overheating features has
turned OFF relay.
Z-Wave products work out of the box after inclusion. Some
device configuration may, however, alter the functionality to
better serve user needs or unlock further enhanced features.
All the parameters below do not feature altering capabilities,
advanced or read only flags.
10
65535
Heating
setpoint
2°C to 40°C.
21°C (Default)
19
20
21
2
2
2
Set setpoint for Heating mode.
Set setpoint for Cooling mode.
Set setpoint for ECO mode.
20
20
20
400
400
400
210
180
180
Cooling
setpoint
2°C to 40°C.
18°C (Default)
ECO
setpoint
2°C to 40°C.
18°C (Default)
| General | Details |
|---|---|
| Name | HEATIT 54 304 59 DIN Smart Thermostat Installation Guide |
| Make | HEATIT |
| Language | English |
| Filetype | PDF (Download) |
| File size | 1.07 MB |
(1 votes, average: 5.00 out of 5)
Loading...
heatit Z-TRM6 DC Z Wave Electronic Thermostat Instruction Manual
HEATIT Z-TRM3 Thermostat User Guide
Heatit Z-TEMP2 Thermostat Installation Guide
heatit Z-TRM3 WiFi Thermostat Instruction Manual
HEATIT Z-Temp3 is a Battery Operated Thermostat Instruction Manual
4512673 Heatit ZM Thermostat 16A User Guide
HEATIT Z-TRM6 Matt Z-Wave Thermostat User Guide
HEATIT 54 305 41 WiFi6 Thermostat Installation Guide
HEATIT Z-TEMP3 Thermostat User Guide
heatit ET-7AW Touchscreen Programmable Thermostat User Manual
Honeywell T4 Lockout Change Thermostat User Manual
DAIKIN DKN509 Wireless Communicating Thermostat Instruction Manual
emos P56211 Wireless Room Thermostat Instruction Manual
Honeywell Home RTH9585WF Smart Color Touchscreen Programmable Thermostat User Guide
vtech W960 E-Smart Thermostat Instruction Manual
sensi 1F95U-42WF Series Touch Smart Thermostat User Guide
Zehnder ComfoControl Ease Installation Guide
Honeywell FocusPRO TH6000 Series Programmable Thermostat Instruction Manual
e l m leblanc TRL 7.26 RF Room Thermostat User Manual
Stelpro Uniwatt UTE202NP NON PROGRAMMABLE ELECTRONIC THERMOSTAT