Home > HEARTH and HOME technologies > HEARTH AND HOME Technologies E474962 Smart Stat Hht Remote Thermostat Instruction Manual

HEARTH AND HOME Technologies E474962 Smart Stat Hht Remote Thermostat Instruction Manual

1. LOW - Battery power low. Replace batteries within two  
weeks.  
2. TIMER - Indicates time remaining before system shuts off,  
when timer-programmed, 9 - hour maximum setting.  
3. MODE - Indicates operation MODE of system. ON indi-  
cates the system is on, either manually or thermostatically.  
THERMO indicates the system will automatically cycle ON/  
OFF, depending on programmed SET temperature. OFF  
indicates the entire system is turned off.  
MODE  
-
+
-
4. SET - Indicates desired SET room temperature for THERMO  
SET  
UP  
operation.  
TIMER  
TIME  
DOWN  
5. FLAME - Indicates burner/valve operational.  
+
6. CLOCK - Indicates the current time  
LIQUID CRYSTAL DISPLAY - LCD  
ON  
in AM/PM.  
X
3
THERMO  
1
OFF  
7. ROOM - Indicates CURRENT room  
temperature.  
4
7
E
E
O
SET  
8. F - Indicates degrees Fahrenheit (ºC  
ROOM  
8
2
indicates degrees Celsius).  
AM  
PM  
6
TIMER  
5
Figure 5. Transmitter LCD Display Sceen  
FLAME  
MATCHING SECURITY CODES  
OPERATING INSTRUCTIONS  
It may be necessary to program the remote receiver to the  
security code of the transmitter upon initial use, if batteries  
are replaced, or if a replacement transmitter is purchased  
from your dealer. To program the remote receiver:  
To operate the system, press the MODE button (Figure  
5) on the transmitter to select the operational MODE  
desired.  
• ON indicates the system is on, either manually, timed or  
thermostatically.  
1. Verify that the receiver is connected to 110-120VAC  
power. Verify that the batteries are installed in the re-  
mote transmitter.  
• THERMO indicates the system will automatically cycle  
ON/OFF, depending on programmed set temperature.  
2. Set the slide button on the receiver to the REMOTE  
position.  
• OFF indicates the entire system is turned off.  
3. Press and release the LEARN button on the top of the  
remote receiver. The receiver will beep to confirm it is  
ready to accept the pairing code from the remote trans-  
mitter.  
Transmitter Settings  
Flip open the plastic cover on the front of the transmitter  
to expose the “SET” buttons.  
4. Press the MODE button on the transmitter. Several beeps  
indicate the transmitter’s code has been programmed  
into the receiver. When an existing receiver is matched  
to a new transmitter, the new security code will overwrite  
the old one.  
NOTE: Flashing numbers on the display indicate the sys-  
tem is waiting for input, such as using the UP and DOWN  
buttons to program a new setting. If no change is made to  
flashing digits within 15 seconds, the system will complete  
the procedure last programmed and reset the display to  
its normal state.  
NOTE: If no “beeping” occurs when the LEARN button is  
pressed and released, take the following steps:  
Verify that the receiver is connected to 110-120VAC power.  
If the receiver still does not provide “beeping” feedback and  
will not pair to the new remote transmitter, press and hold  
the LEARN button for 10 seconds until the receiver emits  
three long “beeps” to confirm the security code memory has  
been cleared. Once the memory is cleared, follow steps  
2 and 3 above to program the transmitter to the receiver.  
4
Hearth & Home Technologies • SMART-STAT Remote Control Instructions • 100-906 Rev. L • 5/18  
GeneralDetails
NameHEARTH AND HOME Technologies E474962 Smart Stat Hht Remote Thermostat Instruction Manual
MakeHEARTH and HOME technologies
LanguageEnglish
FiletypePDF (Download)
File size0.41 MB
Download PDF
1 Star2 Stars3 Stars4 Stars5 Stars (1 votes, average: 5.00 out of 5)
Loading...

HEARTH AND HOME Technologies E474962 Smart Stat Hht Remote Thermostat Instruction Manual