Home > HEARTH and HOME technologies > HEARTH AND HOME Technologies E474962 Smart Stat Hht Remote Thermostat Instruction Manual
HEARTH AND HOME Technologies E474962 Smart Stat Hht Remote Thermostat Instruction Manual
I
S
Piggyback
Connectors
Electronic
Module
LEARN
Brown
Switch
Wires
Remote
Receiver Wires
Figure 3. Wiring Intermittent Pilot Ignition Dry Contact Ignition
The remote receiver has a 3-position slide switch: OFF/
REMOTE/ON (see Figure 4).
NOTE: The slide switch should be placed in the OFF posi-
tion if you will be away from your home for an extended
period of time. Placing the switch in the OFF position also
functions as a safety “lock out” by turning the system off
and rendering the remote receiver inoperative.
REMOTE RECEIVER
110VAC
Input
Dry Contact
(2) 1/4 in. female
connectors
TRANSMITTER
Important: Before operating remote control, transmitter
and receiver must have matching security codes. See
section ‘Matching Security Codes’.
Important: Review ‘Communication-Safety Features’ un-
der ‘Transmitter Safety Features’section. The communica-
tion safety features shut down the fireplace system when
a potentially unsafe condition exists.
Antenna
Important: Review ‘Auto Shutdown’ section. This safety
feature shuts down the fireplace after 9 hours of continuous
operation, in ON mode only.
LEARN
Learn
Important: New or fully charged batteries are essential
for proper operation of the multi-function transmitter. The
transmitter operates on 2 AAA-size 1.5V batteries. Use
Alkaline batteries for longer battery life and maximum
operational performance.
Figure 4. Remote Receiver
Insert 2 AAA-size 1.5V batteries into the battery compart-
ment on the back of the transmitter. When the batteries
are correctly inserted, the screen will display numbers (see
Figure 5 for LCD Display Screen).
NOTE: The remote receiver will only respond to the
transmitter when the 3-position slide button on the
remote receiver is in the Remote position. If the system
does not respond to the transmitter on initial use, see
section Matching Security Codes.
NOTE: If the transmitter is activated from a very cold
condition it may be necessary to allow the transmitter to
stabilize to room temperature (could take up to 15 minutes)
before accurate room temperatures are displayed on the
screen.
1. With the slide switch in the ON position, the system is on.
2. With the slide switch in the REMOTE position, the system
only operates if the remote receiver receives commands
from the transmitter.
NOTE: LCD screen is equipped with a “backlite” for easier
viewing of LCD screen. Backlite illuminates when a function
button is depressed. After 5 seconds elapses, LCD screen
will return to its normal state.
3. With the slide switch in the OFF position, the system is off.
Hearth & Home Technologies • SMART-STAT Remote Control Instructions • 100-906 Rev. L • 5/18
3
| General | Details |
|---|---|
| Name | HEARTH AND HOME Technologies E474962 Smart Stat Hht Remote Thermostat Instruction Manual |
| Make | HEARTH and HOME technologies |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.41 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Dettson R02P034 Communicating Thermostat Instruction Manual
SALUS RT10 Electronic Room Thermostat Instruction Manual
MAPEI 2855201 Dual-voltage Radiant Mapeheat Programmable Thermostat Owner’s Manual
Danfoss RT 115 Thermostat Installation Guide
DOMETIC 3313192.XXX Single Zone LCD Thermostat Instruction Manual
Honeywell TH8000 VisionPro WiFi Thermostat Instruction Manual
Fantini Cosmi C800WIFI Programmable LED Thermostat Instruction Manual
Honeywell Home RTH Series X2S Smart Thermostat Installation Guide
ENGO Controls EONE230W Internet Controlled Thermostat User Guide
Danfoss RAE Radiator Thermostat Installation Guide