Home > HEARTH and HOME technologies > HEARTH AND HOME Technologies E474962 Smart Stat Hht Remote Thermostat Instruction Manual
HEARTH AND HOME Technologies E474962 Smart Stat Hht Remote Thermostat Instruction Manual
Setting the Clock
Setting Desired Room Temperature -
Thermo Operations
1. Press and hold the TIMER/TIME button on the trans-
mitter for more than two seconds. The hour digit(s) will
begin flashing (see Figure 5, Location #6).
This remote control system can be thermostatically con-
trolled when the transmitter is in the THERMO mode.
(THERMO must be displayed on the screen). The transmit-
ter will “sense” the room temperature every two minutes
automatically turning the fireplace ON or OFF thermostati-
cally. To set the desired room temperature:
2. Press the UP or DOWN button until the desired hour is
displayed in AM or PM.
3. After setting the desired hour, press and release the
TIMER/TIME button again to set the minutes; the minute
digits will begin flashing.
1. Press the MODE button to place the transmitter into
THERMO mode. THERMO ON or OFF will display.
4. Press the UP or DOWN button until the desired minutes
are displayed.
2. Press the UP or DOWN button to select the desired
room temperature. The highest SET temperature is 99º
F (37ºC). The lowest SET temperature is 45ºF (7ºC).
5. Press and hold the TIMER/TIME button again for more
than two seconds. The time digits will cease flashing,
indicating the clock has been successfully set. You may
also press the SET button on the transmitter to stop the
time digits from flashing and set the time.
NOTE: To prevent repeated thermo-cycling of the gas
appliance, the sensing unit in the transmitter will only ac-
tivate the remote receiver when the temperature change
exceeds 1º F (1/2º C) above or below the SET (desired)
temperature.
When the transmitter is in the THERMO mode, it should be
kept away from direct sources of heat such as fireplaces,
incandescent lighting and direct sunlight. Leaving the trans-
mitter in direct sunlight, for example, will cause it to read
the room temperature higher than it actually is.
SETTING
BUTTON
Setting the Countdown Timer
This remote control system can operate with a built-in
countdown timer when the transmitter is in the ON or
THERMO modes (THERMO or ON must be displayed on
the LCD screen).
-
+
1. Press and release the TIMER/TIME button on the trans-
mitter. The word TIMER and 0:15 flash on the screen
(see Figure 5, Location #2).
Figure 6. Setting Button/Child Proof Lockout
2. Press the UP and DOWN button to begin advancing
through each of the countdown time options. Available
countdown times are 15 min, 30 min, 45 min, 1 hour,
1 hr 30 min, and each additional half hour up to nine
hours.
Setting ºF / ºC Scale
The factory setting for temperature is degrees Fahrenheit(ºF).
To change this setting to degrees Centigrade (ºC):
3. To set the TIMER, press the SET button on the transmit-
ter. If the system is ON, it will remain on until the “time”
has expired. If the system is in the THERMO mode, it
will cycle on and off as the room temperature requires
until the “time” has expired.
1. Remove the battery cover on the back of the transmit-
ter and locate the “setting button” at the top center of
battery compartment (see Figure 6).
2. Push setting button and ºF will begin flashing on the
NOTE: When the timer is used in the THERMO mode,
the THERMO operation will discontinue when the “time”
has expired.
LCD screen (see Figure 5, Location #4).
3. Push the DOWN button on the transmitter to change ºF
to ºC.
4. Push “setting button” on transmitter and Centigrade (ºC)
degree readings will display on LCD screen.
Low/Battery Indicator
An “X” outlined by a battery on the right side of the LCD
screen will appear when battery power has dropped sig-
nificantly. At this time, approximately two weeks of battery
power remains.
5. Repeat this process to change back to Fahrenheit (ºF)
reading, this time pushing the UP button. NOTE: LCD
screen will return to normal state if setting button is not
pushed within 15 seconds.
Hearth & Home Technologies • SMART-STAT Remote Control Instructions • 100-906 Rev. L • 5/18
5
| General | Details |
|---|---|
| Name | HEARTH AND HOME Technologies E474962 Smart Stat Hht Remote Thermostat Instruction Manual |
| Make | HEARTH and HOME technologies |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.41 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Danfoss TP5001B Programmable Room Thermostat User Guide
PRO1 T805 Non Programmable Thermostat Instruction Manual
TRU COMPONENTS TC-NTL-ExT6 Hazardous Area Thermostat Instructions
JUMO exTHERM-AT Explosion-Protected Surface-Mounted Thermostat Instruction Manual
MOES BHT-006 Series Smart Heating Thermostat User Manual
GENERAL Life MITRA 250S RF Wireless Room Thermostat User Guide
GENERAL HT300S Wired Room Thermostat User Guide
nVent RAYCHEM ETS-05 Electronic Thermostat Instruction Manual
SEELEY Ducted Gas Heater with MagiQtouch Controller or Manual Thermostat Owner’s Manual
GE Programmable CYNC Smart Thermostat User Guide