CH200SA Versatile Deluxe Low Voltage Thermostat Installation Guide

1

2

3

4

SELECTING THERMOSTAT LOCATION  

INSTALLATION  

INSTRUCTIONS  

The proper location of the room thermostat is most  

important to insure that it will provide a comfortable home  

temperature. Observe the following general rules when  

selecting a location:  

1. Locate it about 5 ft. above the floor with a free flow of  

air.  

2. Install it on a partitioning wall, not on an outside wall.  

3. Never expose it to direct light or radiation from lamps,  

sun, fireplaces, etc.  

4. Avoid locations close to doors that lead outside,  

windows, or adjoining outside walls.  

5. Avoid locations close to radiators, warm air registers, or  

in the direct path of heat from them.  

CH200SA & CH400SA  

VERSATILE DELUXE LOW  

VOLTAGE THERMOSTAT  

6. Make sure there are no pipes or duct work in that part of  

the wall chosen for the thermostat location.  

7. Never locate it in a room that is warmer or cooler than  

the rest of the home such as kitchen or hallway or on  

the opposite side of the wall of a cold or unused room.  

52010  

8. The living or dining room is normally a good location,  

provided there is no cooking range or refrigerator on  

opposite side of wall.  

CH200SA  

INSTALLATION  

1. Remove cover from thermostat by pulling outward. Pull  

thermostat wires through small holes beside terminal  

screws on thermostat base and connect wires to proper  

terminal screws per wiring diagrams. Note that on some  

models wire leads may be connected to terminal screws  

on back of base.  

LUX  

2. The thermostat can either be mounted to a standard  

horizontal outlet box or mounted directly to the wall.  

Place level on top of thermostat base and mark hole  

locations for mounting screws.Push excess wire into  

wall or switch box and plug up hole to prevent drafts  

from affecting thermostat operation. Then attach  

thermostat base loosely to wall with the two screws  

provided.  

CH400SA  

3. Again place level on top of thermostat base to be sure it  

is level. Then tighten mounting screws securely and  

snap on thermostat cover.  

LUX  

HEATING ANTICIPATOR  

The heating side of this thermostat is equipped with an  

adjustable heater. Set heater indicator to match the  

current rating of the primary control. The heater may be  

adjusted for current ratings from .2 to 1.2 Amp.  

W A R N I N G  

Not for use with compressors without time delays.  

Additional adjustments, if necessary, may be made as  

follows:  

BURNER CYCLES TOO LONG - Set adjustable heater to a  

slightly lower dial setting (1/2 division).  

SPECIFICATIONS  

BURNER CYCLES TOO SHORT - Set adjustable heater to a  

slightly higher dial setting (1/2 division).  

24 Volts A.C.  

Electrical Rating: 24 to 30 Volts A.C.  

Heat Anticipator: 0.20 to 1.2 Amp. Max.  

Cool Anticipator: 0 to 1.0 Amp. Max.  

W A R N I N G  

The Adjustable Heater (Heat Anticipator) WILL BURN OUT if 25V  

are applied directly to thermostat by shorting out the gas valve or  

primary control during testing or by incorrect wiring.  

© 2007 LUX PRODUCTS CORPORATION. ALL RIGHTS RESERVED  

1

https://manual-hub.com/  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	CH200SA Versatile Deluxe Low Voltage Thermostat Installation Guide
Make	LUX
Language	English
Filetype	PDF (Download)
File size	0.14 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• LUX

CH200SA Versatile Deluxe Low Voltage Thermostat Installation Guide Overview

Summary of Contents

• Page 1: Selecting thermostat location is crucial for maintaining a comfortable home temperature. Locate the thermostat about 5 ft. above the floor with free air flow. Install it on a partitioning wall, avoiding outside walls. Do not expose the thermostat to direct light or radiation. Avoid locations near doors, windows, or outside walls. Keep it away from radiators and warm air registers. Ensure there are no pipes or duct work in the wall where the thermostat is installed. Do not place it in rooms that are significantly warmer or cooler than the rest of the home. The living or dining room is generally a good location, provided there are no heat sources on the opposite wall. The heating side of the thermostat has an adjustable heater for current ratings from 0.2 to 1.2 Amp.
• Page 2: Wiring diagrams Cooling systems Heating systems Fan relay Cooling compressor Heating control Heating transformer Cool transformer Heating/cooling systems 4- or 5-wire with one transformer 5- or 6-wire with two transformers
• Page 3: These diagrams below are provided for new installations or unreferenced wires. Typical hookup for 2-wire 24V heating system and millivolt system. Typical hookup for 3-wire heat system if third wire is fan wire. Typical cooling and heating system (4-wire). Typical cooling and heating system (5-wire). Remove jumper between RH & RC. Note: If you have an electric system and the blower does not operate after installation, find the factory installed yellow wire currently attached to the “Y” terminal and move it to the “A” terminal on the sub-base.
• Page 4: Technical assistance is available for installation or usage problems. Review the instruction manual thoroughly for guidance. Contact the Technical Assistance Department during regular business hours for help. Online technical assistance is available anytime through the company's website. The limited warranty covers defects in materials or workmanship for three years from the original purchase date. The warranty does not cover damage from misuse or failure to follow installation instructions. Return malfunctioning units to the retailer with proof of purchase. The warranty may not apply in some states due to variations in laws. The product does not contain mercury but may replace a unit that does. Proper disposal instructions for mercury should be obtained from local waste management authorities.