Schluter DITRA-HEAT-E-RS1 Smart Thermostat Instruction Manual

1

2

3. Connect the temperature sensor as shown. Use  

the floor temperature sensor supplied with the  

DITRA-HEAT-E-HK heating cable(s). Any other  

type of sensor used needs to be 300 volt rated  

and meet the other requirements of the electrical  

codes in your region.  

5. Replace the cover and tighten the screw at the  

bottom.  

2. Settings Which Can Be Modified with the Device  

THERMOSTAT INSTALLATION  

APPLICATION SETTINGS  

(Can also be done with the app)  

MANUAL TEMPERATURE  

ADJUSTMENTS  

CONNECT THE THERMOSTAT  

TO THE SCHLUTER^® SMART  

THERMOSTAT APP  

Parameter and  

possible settings  

Setting No.  

Name  

Further Explanation  

1. Loosen the screw  

at the bottom and  

remove the faceplate.  

1. Press the dot soft button and hold for 1 second to  

access the menu. Press the appropriate arrow to  

move up and down into the choices and press the  

dot soft button to make a selection and move to  

the next parameter, until reaching the end.  

Temperature unit:  

°F or °C  

(default: °F)  

Installation Manual  

Schluter^®-DITRA-HEAT-E-RS1  

Smart Thermostat  

To adjust the temperature, press the up or  

down arrow to change the set point temperature.  

1

Temperature  

1. If you do not yet have an account, download  

the Schluter^® Smart Thermostat app for iOS or  

Android™ to create an account and add your  

device.  

The thermostat offers 2 temperature regulation modes:  

Control Mode:  

Floor or Ambient  

(default: Floor)  

Floor mode: Regulates floor temperature by means of an external floor  

temp. sensor.  

2

3

Control  

Ambient mode: Regulates ambient temperature by means of an internal  

temp. sensor.  

6. Power up the thermostat. After performing a test  

sequence, the thermostat should display the floor  

temperature. If not, refer to the troubleshooting  

guide in this manual.  

Max. floor temperature limit  

when in Floor control mode or  

in Ambient mode:  

This function limits the floor temperature when in floor control mode  

or in ambient control mode. This is ideal for preventing uncomfortable  

temperatures, or for preserving floor coverings other than ceramic or stone  

tiles. The recommended max. set point temperature for alternative floor  

coverings (e.g. LVT flooring, laminate flooring, etc.) is 82°F or 28°C. When  

reaching 82°F (28°C), “Laminate flooring” will be displayed.  

2. Connect the heating cable to the load terminals  

and the power supply wires to the line terminals  

located on the back of the thermostat. Connect  

the heating cable ground wire to the grounding  

screw in the electrical junction box.  

Max Floor  

Temperature  

41°F to 97°F  

(OFF option, available only in  

ambient control mode)*  

An auxiliary output provides one of three functions for an additional heating  

source:  

2. Tap the menu icon on your smart phone, then  

select “Add Device”  

Auxiliary output:  

OFF, EXP, Fast, Long  

(default: OFF)  

EXP: For connecting one or more Schluter^®-DITRA-HEAT-E-RRS power  

modules  

4

5

Aux Output  

Fast and Long: For adding second stage heating when in ambient control  

mode (Please consult our White Paper on this subject in the “Download”  

section of this thermostat on our website.)  

This installation manual is subject to change without notice.  

Please visit www.schluter.com for the latest version.  

4. Use the screws  

provided to secure  

the thermostat  

to the electrical  

junction box.  

Floor temperature sensor:  

10K or 12K  

(default: 10K)  

Floor Sensor  

WARNINGS  

The installation of this thermostat must be performed by qualified personnel  

and comply with the national and local electrical codes and regulations.  

* In floor control mode, the set point  

limit is 97°F (36°C).  

To avoid electric shock, disconnect the heating system power supply at the  

main electrical panel before installation and maintenance of the thermostat.  

3. Follow the steps of the Installation Wizard.  

2

3

4

5

6

7

8

9

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	Schluter DITRA-HEAT-E-RS1 Smart Thermostat Instruction Manual
Make	Schluter
Language	English
Filetype	PDF (Download)
File size	0.29 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• Schluter

Schluter DITRA-HEAT-E-RS1 Smart Thermostat Instruction Manual Overview

Summary of Contents

• Page 1: Connect the temperature sensor as shown. Use the floor temperature sensor supplied with the DITRA-HEAT-E-HK heating cable(s). Settings which can be modified with the device. Manual temperature adjustments. Connect the thermostat to the Schluter® Smart Thermostat app. The thermostat offers 2 temperature regulation modes: Control Mode: Floor or Ambient. Floor mode regulates floor temperature by means of an external floor temperature sensor. Ambient mode regulates ambient temperature by means of an internal temperature sensor. Power up the thermostat. After performing a test sequence, the thermostat should display the floor temperature. Max floor temperature limit when in Floor control mode or in Ambient mode prevents uncomfortable temperatures. The installation of this thermostat must be performed by qualified personnel and comply with the national and local electrical codes and regulations.
• Page 2: Connecting the DITRA-HEAT-E-RRS power module(s) Ground fault protection can detect a current leakage of 5 mA. When a current leakage is detected, the ground fault protection interrupts the power supply. Press any button to turn back ON the thermostat from standby mode. The thermostat will resume operation under its last program settings. Setpoint range is 5° C to 36° C (41° F to 97° F). This thermostat has an Auto Test which periodically verifies the correct operation of the protection circuit. GFCI protection is Class A (5 mA). The Schluter-DITRA-HEAT-E-RRS power module is recommended for more than 15 amps in a room. This device complies with Industry Canada license exempt RSS standard(s).