SALUS HTRP230(50) Wired Programmable Digital Thermostat User Manual
Installer parameters
6
Manual mode – temperature setpoints
AUTO mode – NSB function
Repeat steps 4 to 6 to set
the time and temperature
for further points of the
schedule. No time (--:--)
on the display means that
thermostat will skip the
time interval. 6 points are
available for the schedule.
Parameter
Values
Default
Values
dxx
Function
Description
3
temperature levels are available. In manual mode, only
one temperature level is maintained for the entire day. Icon
in the frame indicates which mode is currently active.
The NSB (Night Setback) function enables automatic reduction of
the temperature setpoint on the HTRS230(30) SLAVE thermostat, via
the HTRP230(50) programmable MASTER thermostat connected to the
wiring centre (or other external clock). The temperature change takes
place between the comfort temperature mode and economic
temperature mode.
0
1
2
According to the PWM algorithm
Hysteresis 0.5°C ( 0.25°C)
Hysteresis 1.0°C ( 0.5°C)
A different temperature can be set for each level.
d01 Heating Control
Displayed
0
Select work mode using
or buttons. Confirm by
button.
- Comfort temperature mode
If the thermostat indicates an
incorrect temperature, then it can
be corrected 3.0°C
-3.0°C
to + 3.0°C
D02
temperature
correction
0°C
0
To activate AUTO mode, select the icon. Together with the icon,
the thermostat shows the active temperature mode on the display:
- Economic temperature mode
0
1
External sensor not connected
External sensor connected
External sensor
connection
(S1/S2)
or
.
Heating / Cooling mode
D03
- Frost protection mode Usually used during the period of
absence or during the holidays (only available in HEATING
mode).
Press any button to highlight the screen, then follow the steps
below:
Manual change:
Modes are indicated by
The D03 parameter must be set to
"1" – then, if the D04 parameter
is set to "0", the thermostat only
measures the temperature at the
external sensor
symbols.
Press and hold button to enter the menu, then use button to select
the Heating / Cooling mode change setting. Confirm changes using
button. Now use or buttons to set the heating or cooling mode.
Confirm by button.
0
1
The thermostat also has 2 additional modes:
1
2
External sensor
used as Air
sensor or Floor
sensor
d04
0
- The PARTY mode sets the comfort
defined time (maximum 9 hours 50 minutes).
temperature for a user-
The D03 parameter must be set to
"1" – then, if the D04 parameter
is set to "1", the sensor is used as
floor overheating protection.
Automatic change (via CO terminal):
-
The HOLIDAY mode sets the frost protection mode for a
user-defined time (maximum 99 days).
The heating/cooling mode can be changed automatically via the CO
terminal in the thermostat. If 230 V AC power supply is connected to the
CO terminal – then thermostat automatically switches to cooling mode.
If you want to use this function, then you have to change the value of the
D18 parameter to "1".
1
2
0
1
Hysteresis 0.5°C ( 0.25°C)
Hysteresis 1.0°C ( 0.5°C)
Disabled
D05 Cooling Control
D07 Valve Protection
2
1
Select AUTO mode using
or buttons.
Press any button to highlight the screen, then follow the steps
below:
Enabled
Cooling blocking:
When D19 thermostat parameter is set to "1", then cooling is blocked
for a single room. When the cooling function is blocked, no message is
displayed.
The frost protection temperature
D08 Frost Setpoint 5°C – 17°C is maintained for example during
active holiday mode.
1
2
5°C
1
Note:For the proper NSB function work, an appropriate cable
connection is required. The connection description is on the
previous page.
0
1
12 hours
24 hours
12/24 Hour
Format
D09
D10
D11
Installer mode
Time zone
(reserved for
internet wireless)
It gives you the possibility to fit
the thermostat time zone to yours
(every 1 hour step).
Schedule programming
from -13 to
+13 hours
0
Press any button to highlight the screen, then follow the steps
below:
Press any button to highlight the screen, then follow the steps
below:
0
1
Off
On
Daylight Saving
Time (DST)
Select work mode using
or buttons.
1
1
2
1
2
Heating setpoint
limits
Maximum temperature which can
be set for heating
D12
D13
5°C – 35°C
5°C – 40°C
35°C
5°C
Cooling setpoint
limits
Minimum temperature which can
be set for cooling
Temperature setpoint
Floor sensor
protection limit
(heating high
limit-HL)
In order to protect floor againts
overheating – heating will be
turned off when floor sensing temp
is higher than protection limit
Press any button to highlight the screen, then follow the steps
below:
3 sec.
3 sec.
D14
D15
11°C – 45°C
6°C – 40°C
27°C
10°C
6°C
3 sec.
Select the 49 code using
or buttons.
Press and hold and
buttons simultaneously for
3 seconds.
Confirm selection
by button.
Floor sensor
protection limit
(heating low
limit-LL)
In order to protect floor againts
overcooling – heating will be
turned on when floor sensing temp
is lower than protection limit
Press and hold button
for 3 seconds.
2
1
3
4
3
Use button to select
days period:
- whole week
In order to protect floor againts
overcooling – heating will be
turned on when floor sensing temp
is lower than protection limit
Floor sensor
D16 protection limit 6°C – 45°C
(cooling)
- working days
- weekends
You are now in the installer
menu.
Select one of these 5 default
programs. Once selected, default
program will overwrite present
program. Selected default
program can be edited by the user
in the User Setting Mode.
Current temperature.
Temperature setpoint
in the selected work mode.
- each day separately
Preset program
selection
Confirm selection by button.
D17
1-5
1
Select the parameter you wish
to change by or buttons
and enter using button.
Use and to set the value
of the parameter, and then
Confirm selection
by button.
4
3
4
5
Heat/Cool Mode
Selection
0: Manual with buttons use
1: Automatic by the CO terminal
D18
D19
0 or 1
0 or 1
0
0
confirm it with
.
Cooling Blocking
function
heating / cooling
0: Cooling disabled
1: Cooling allowed
Set the hour for the first time
Set the minutes for the first
time interval in the schedule
using or buttons.
Confirm selection by
button.
interval in the schedule using
or buttons. Confirm
selection by button.
Note: To restore default settings – set the P47 code during
2 step and then confirm your choice using or buttons.
Actuators
loading selection
for different
temperature
compensation
Set the temperature
setpoint using
or buttons.
Numbers 1 to 5 are the numbers
of actuators connected to the
thermostat.
Confirm by button.
D20
1 to 5
1
| General | Details |
|---|---|
| Name | SALUS HTRP230(50) Wired Programmable Digital Thermostat User Manual |
| Make | SALUS |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.35 MB |
(1 votes, average: 5.00 out of 5)
Loading...
SALUS IT800 WIFI Smart Thermostat Installation Guide
SALUS 091FLRF Wireless Room Thermostat User Guide
SALUS Thermostat Sensor TS600 User Guide
SALUS Thermostat and Smart Plug Installation Guide
SALUS Programmable Wired Thermostat VS30W/VS30B Installation Guide
SALUS Wired Thermostat Installation Guide
SALUS Wired Digital Thermostat – Non-programmable HTRS230 User Manual
SALUS RT520 Radiator Thermostat User Guide
SALUS RT310 Thermostat User Manual
SALUS Thermostat RT520 User Manual
GENERAL LIFE SOLARA 300S Digital Room Thermostat User Manual
SALUS SQ610RF Smart Thermostat Instruction Manual
Honeywell Home DT4 Wired Room Thermostat Installation Guide
EPH CDTP2 Room Thermostat Installation Guide
aube technologies TH150 Series VAV Thermostat User Guide
GENERAL LIFE MITRA 220 Digital Room Thermostat User Manual
Schneider Electric Wiser Radiator Thermostat Instructions
Amana DS01G Digi Smart Thermostat Instruction Manual
GENERAL LIFE MITRA 230S Digital Room Thermostat User Manual
Beca BAC-006 Zigbee Thermostat User Guide