Pro1 Technologies Pro1 T701i WiFi Thermostat Installation Guide

1

2

3

Product Installation Guide  

Installation Tips  

Wall Installation  

The thermostat should be installed approximately 4 to 5 feet above the floor.  

Select an area with average temperature and good air circulation. Pick an  

installation location that is easy for the user to access. The temperature of the  

location should be representative of the building.  

T701i  

Pro1 Technologies  

P.O. Box 3377  

Springfield, MO 65808-3377  

Do not install  

thermostat in locations:  

Toll Free : 888-776-1427  

Web: www.pro1iaq.com  

Hours of Operation: M-F 9AM - 6PM EST  

PM-T701i-IM-2219  

*PM-T701i-IM-2219*  

Hardwire (24V Common Wire)  

• Close to hot or cold air ducts  

• That are in direct sunlight  

• With an outside wall behind the  

thermostat  

• In areas that do not require  

conditioning  

• Where there are dead spots or  

drafts (in corners or behind doors)  

• Where there might be concealed  

chimneys or pipes  

Power Type  

Thermostat Application Guide  

Description  

Gas or Oil Heat  

Yes  

Yes  

No  

No  

A trained, experienced  

technician must install this product.  

Electric Furnace  

Heat Pump (No Aux. or Emergency Heat)  

Heat Pump (With Aux. or Emergency Heat)  

Multi-Stage Systems  

Carefully read these  

instructions. You could damage this  

product or cause a  

hazardous condition if you fail to  

follow these instructions.  

No  

Yes  

Yes  

Heat Only Systems  

Cool Only Systems  

No  

Millivolt  

Removing The Private Label Badge  

Una version en espanol de este  

manual se puede descargar en la  

pagina web de la compania.  

Table of Contents  

Page  

Specifications  

1

2

3

4

5-6  

Gently slide a screwdriver into the  

bottom edge of the badge. Gently  

turn the screwdriver counter  

Installation Tips  

Thermostat Quick Reference  

Subbase Installation  

Wiring  

clockwise. The badge is held on by  

a magnet in the well of the battery  

door. The badge should pry off easily.  

Technician Setup  

WIFI Setup  

Specifications  

7-8  

9-11  

12  

Use the bevel on lower ridge  

DO NOT USE FORCE.  

All of our thermostats use the same  

universal magnetic badge. Visit the  

company website to learn more about  

our free private label program.  

Magnet in door  

U.S. Registered Trademark. Patents pending  

Copyright 2022 All Rights Reserved.  

1

2

Rev. 2251  

Thermostat Quick Reference  

Subbase Installation  

Horizontal Mount  

For horizontal mount put one  

screw on the left and one screw  

on the right.  

LCD Display  

Set At  

Glow in the dark light button  

Fan Button  

Vertical Mount  

For vertical mount put one  

screw on the top and one screw  

on the bottom.  

System Button  

Temperature Setpoint Buttons  

Private Label Badge  

Electrical Hazard  

Failure to disconnect the power before  

beginning to install this product can cause  

electrical shock or equipment damage.  

Set At  

Mercury Notice  

NOTE: To ensure a solid fit between  

the thermostat and subbase:  

1. Mount subbase on a flat wall.  

2. Use provided screws.  

COOL ON  

HEAT ON  

FAN ON  

All of our products are mercury free.  

However, if the product you are replacing  

contains mercury, dispose of it properly.  

Your local waste management authority  

can give you instructions on recycling and  

proper disposal.  

3. Ensure drywall anchors are flush with wall.  

4. Push wires into wall.  

Mount Thermostat  

Em.Heat  

^STAGES AutoCool  

Indicates the current room temperature  

1

2

3

Setpoint: Displays the selected setpoint temperature.  

Set At  

System Operation Indicators: The COOL ON, HEAT ON or FAN ON will display  

when the COOL, HEAT, or FAN is on. The compressor delay feature is active if these  

are flashing.  

Align the 4 tabs on the subbase  

with corresponding slots on the  

back of the thermostat, then  

push gently until the  

WIFI Indicator: Shown when connected to WiFi.  

thermostat snaps in place.  

Globe: Globe is displayed if an energy efficient temperature has been selected.  

Fan: Indicates the current fan setting.  

Stages: +1 will appear in the display when the first stage of heat or cool is  

on.  

7

System: Indicates current system mode setting.  

4

3

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	Pro1 Technologies Pro1 T701i WiFi Thermostat Installation Guide
Make	Pro1 Technologies
Language	English
Filetype	PDF (Download)
File size	0.26 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• Pro1 Technologies

Pro1 Technologies Pro1 T701i WiFi Thermostat Installation Guide Overview

Summary of Contents

• Page 1: Product installation guide The thermostat should be installed approximately 4 to 5 feet above the floor. Select an area with average temperature and good air circulation. The temperature of the location should be representative of the building. Do not install thermostat in locations close to hot or cold air ducts, in direct sunlight, with an outside wall behind the thermostat, in areas that do not require conditioning, where there are dead spots or drafts, or where there might be concealed chimneys or pipes. A trained, experienced technician must install this product. Carefully read these instructions to avoid damaging the product or causing a hazardous condition. Gently slide a screwdriver into the bottom edge of the badge to remove it. All of our thermostats use the same universal magnetic badge. Failure to disconnect the power before beginning to install this product can cause electrical shock or equipment damage. All of our products are mercury free.
• Page 2: Wiring Caution: Electrical hazard. Failure to disconnect the power before beginning to install this product can cause electrical shock or equipment damage. If you are replacing a thermostat, make note of the terminal connections on the thermostat that is being replaced. A 24 VAC 500mA common connection is required with this thermostat. All components of the control system and the thermostat installation must conform to Class II circuits per the NEC Code. This thermostat requires a 24V common wire to the C terminal. Do not overtighten terminal block screws, as this can damage the terminal block. Devices such as a float switch that mechanically break circuits should be installed so that they break the control wire (Y) not the power (R). Technician Setup Menu Press and hold the + and - buttons for 3 seconds to enter tech setup. This feature allows you to set a maximum heat setpoint value.
• Page 3: WIFI setup steps are intended for viewing information and resetting your WIFI connection. The WIFI reset process is necessary for applications like replacing WIFI routers or changing networks. To reset the WIFI connection, press and hold the + and – buttons together for 3 seconds, then press and hold the WIFI button. You can change settings using the + or - buttons and navigate through steps with the lower left and right buttons. To exit tech setup, press and hold the + and - buttons for 3 seconds or wait 60 seconds. The thermostat will display “WIFI RESET” indicating it is no longer connected to the local WIFI network. The WIFI firmware identification number can be used for troubleshooting. The control range of temperature is 44˚F to 90˚F (7˚C to 32˚C). The power source required is 18 to 30 VAC, NEC Class II, 50/60 Hz for hardwire. Operating humidity should not exceed 90% non-condensing maximum.