PBU 2 Degrees 2 Save Thermostat User Manual
3. Do not spray any liquid directly on the thermostat.
Spray liquids onto a cloth, then use the damp cloth to
clean the screen. Use water or household glass cleaner.
Avoid abrasive cleansers.
Changing Your Fan Control
Press FAN to select fan operation, then press DONE.
• ON:Fan is always on.
Thermostat Settings
Setting Current Time and Day
• AUTO:Fan runs only when the heating or cooling
system is on.
4. After 30 seconds, press CANCEL to resume normal
operation, or press OK if you require more time for
cleaning.
The clock should never require adjustment since it
automatically updates for daylight-saving time and stores all
date/time information. Should the time and date need to be
reset after a power failure, this is an indication that the battery
needs to be replaced. To manually set the current time display:
• CIRC:Fan runs randomly, about 35% of the time,
not counting any run time with the heating or cooling
system.
Online Access
Program Your Thermostat Online
1. Press CLOCK, then press s or t to adjust the time.
(Press and hold s or t to advance the time more
quickly.)
You can press FAN to override the fan settings you have
programmed for different time periods. If you select ON or
CIRC, the setting you select remains active until you press
FAN again to select AUTO.
you will see is the login screen.
2. Press DONE to save and exit (or press CANCEL to exit
without changing the time).
Temporary Setting Changes
User ID and Passwords
Programming or Changing Settings for
Heating and Cooling
The thermostat enables you to temporarily change your
settings without losing any pre-programmed schedules.
The default User ID is your BPU account number.
The default Password is the serial number for your
thermostat. That number can be found on the work order
the installer left at the time of installation or on the bottom
of the thermostat. Please allow up to three days after your
thermostat is installed for us to have your information
accessible online.
Press s or t to immediately adjust the temperature. This
temporarily overrides the temperature setting for the current
time period.
There are five (5) system modes. Press the SYSTEM button
to select one of the following, then press DONE. Pressing the
SYSTEM button successively will toggle the thermostat from
one mode to the next.
The new temperature is maintained only until the next pre-
programmed time begins. For example, if you want to turn up
the heat early in the morning, it will automatically be adjusted
later, according to the pre-programmed schedule.
• HEAT:Thermostat controls only the heating system.
• COOL: Thermostat controls only the cooling system.
• OFF: Heating and cooling systems are off.
To reset your User ID and Password after your initial login,
click on CHANGE LOGIN at the bottom left of the screen.
BPU personnel do not have access to your User ID and
Password once it has been changed. For future reference,
record your User ID and Password in the following space:
To cancel the temporary setting at any time, press CANCEL or
SCHED. The pre-programmed schedule resumes.
• AUTO: Thermostat automatically selects heating or
cooling depending on the indoor temperature.
Permanent Setting Changes
• EMHEAT (only for heat pumps with auxiliary heat):
The thermostat enables you to temporarily change your
settings without losing any pre-programmed schedules.
Thermostat controls emergency and auxiliary heat.
USER ID
PASSWORD
It’s easy to program your system for maximum energy
savings. You can program four time periods with different
settings. Times can be programmed in 15-minute increments.
Change Thermostat Settings Online
Press s or t to immediately adjust the temperature.
This temporarily overrides the temperature setting for the
current time period and when followed by pressing HOLD,
permanently adjusts the temperature.
1. On the left side, under Thermostat, click on your serial
number to see the drop-down menu. If you have more
than one thermostat installed, all of the serial numbers
will be listed. Each one can be programmed individually.
1. Press SCHED, then press EDIT.
2. Press day buttons to select day(s).
Pressing HOLD turns off the program schedule, but the
program settings are retained and can be resumed by
pressing CANCEL or SCHED to cancel HOLD and reactivate
the pre-programmed schedule.
2. Click on SCHEDULES in the drop-down menu. The
Last Schedule Sent from the web interface will appear
at the top of your screen.
3. Press s or t to set WAKE time for selected day(s).
4. Press s or t to set HEAT and COOL temperature for
this time period.
Clean the Screen
Create a New Schedule
5. Press other time periods (LEAVE, RETURN, SLEEP) to
set time and temperatures for each.
1. Press SCREEN to go to the cleaning screen.
1. Click on CREATE.
6. Press DONE to save and exit (or press CANCEL to exit
without saving changes).
2. Press OK to lock the screen for cleaning. The screen
remains locked for 30 seconds so you can clean the
screen without changing any settings.
2. Select one of the scheduling options. Then click on
NEXT.
NOTE: You can press CANCEL PERIOD to eliminate any unwanted time
period.
3. Click in the name field, and type the name you wish to
use for the schedule (e.g., Normal or Vacation).
| General | Details |
|---|---|
| Name | PBU 2 Degrees 2 Save Thermostat User Manual |
| Make | PBU |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.1 MB |
(1 votes, average: 5.00 out of 5)
Loading...
HITACHI ATW-RTU-05 Wireless Intelligent Room Thermostat Instruction Manual
Danfoss VIIDH102 Living Connect Intelligent Radiator Thermostat User Guide
Roth SL Car Air Conditioner Thermostat Instructions
Honeywell RTH2510 Programmable Thermostat Owner’s Manual
Danfoss CAS 178 Thermostat Installation Guide
beca BAC-003 Series WiFi Thermostat Fan Coil
Amana DS01G Digi Smart Thermostat Instruction Manual
Honeywell RTHL2510 Series Programmable Thermostat Owner’s Manual
Robertshaw RS9220 Digital Programmable Wall Thermostat Instruction Manual
WIFI Temp2 Battery Operated Thermostat Installation Guide