EUROSTER 2026TXRX Air Conditioning Thermostat Instruction Manual
EUROSTER 2026TXRX – INSTALLATION AND OPERATION MANUAL
11
•
•
•
•
insert the second receiver into a mains socket.
Press the button on the receiver 3 times – the blue LED lights up,
when the receiver is detected, the blue led goes out,
Proceed similarly with the connection of the subsequent receivers, then press the
button on the transmitter board. The pairing mode is ended.
Caution! Pairing mode is only available for 10 minutes after connecting the receiver
to the mains, resetting it, or installing batteries in the thermostat!
Factory-established pairs are paired, however, pairing may be repeated if necessary.
SELECTING OPERATING MODE
While holding the "B" button pressed, insert the receiver into a mains socket. Depending on
the mode set, the green or red LED lights up. Each time the button is pressed, the operating
mode changes. When you select the mode, the receiver restores operation.
Green – normally open mode (COM – NO). It is the mainly used operation mode. While the
device operation indicator is active, the output cables are shorted.
Red – normally closed mode (COM – NC). While the device operation indicator is active, the
output cables are opened.
Caution! The factory default setting is (COM-NO).
9. FIRST START
When inserted into the mains socket, the receiver indicates the relay operating mode. A flash
of green LED – normally open mode (COM-NO), a flash of red – normally closed mode (COM-
NC).
Any change in the status of the thermostat (switching the heating on/off) is made immediately
by the receiver, while the confirmation that the radio signal is received from the transmitter is
repeated every 15 minutes.
RADIO SIGNAL STRENGTH
The radio signal strength is indicated together with the reception of the transmitter signal.
Radio signal reception is indicated in green. LED flashing three times stands for a very strong
range, twice for a strong range, and once for sufficient range.
NO RADIO COMMUNICATION
If the communication between the thermostat and the receiver is interrupted (e.g. discharged
batteries) and if this condition lasts for 60 minutes (no response from the receiver), the
receiver switches to the frost protection mode. The heating device will be switched on every 3
hours for 20 minutes to prevent the rooms from being cooled down. At the time of re-
establishing communication (e.g. replacement of batteries), the receiver will automatically
switch the system off and resume operation.
If there is no radio communication, the green LED flashes rapidly.
CONTINUOUS OPERATION OF HEATING DEVICE (MAN)
In the event of system failure, it is possible to manually switch on the heating. Move the switch
on the RX receiver to the MAN position. Such status is indicated by a rapid flashing of the red
LED.
RECEIVER SIGNALING TABLE.
Function
Pairing
Signaling
Blue
Reception of radio signal
No radio communication
The heating/air-conditioning device is switched on
Manual mode
Green
Green – flashing
Red
Red – flashing
| General | Details |
|---|---|
| Name | EUROSTER 2026TXRX Air Conditioning Thermostat Instruction Manual |
| Make | EUROSTER |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.62 MB |
(1 votes, average: 5.00 out of 5)
Loading...
EUROSTER 4040 Smart Programmable Thermostat User Manual
EUROSTER 2006TXRX Wireless Programmable Thermostat Installation Guide
Robertshaw RS8210 Thermostat Installation Guide
SIEMENS RDY2000BN BACnet Commercial Thermostat User Manual
resideo TH2110WF4008 Smart Thermostat User Guide
Wiser CCTFR6400 Room Thermostat User Manual
SASWELL T11FHL Heated Floor Thermostat User Manual
MYSAIR MS20 Thermostat User Manual
meross MTS200HK Smart Wi-Fi Thermostat User Manual
EUROTRONIC COMET Programmable Energy Saving Radiator Thermostat User Manual
sygonix 2735095 Wireless Heating Thermostat Instruction Manual
DAIKIN DKN509 Wireless Communicating Thermostat Instruction Manual