ENGO E20i Series Wi-Fi Wireless Internet Thermostat User Guide
8
4
Installer parameters
7
Installation of thermostat in the app
STEP 3 - CONNECT THE THERMOSTAT TO WI-FI
Default
value
Make sure your router is within range of your smartphone.
Make sure you are connected to the Internet. This will reduce
the pairing time of the device. Use only Wi-Fi 2,4GHz network
Wi-Fi 2,4GHz
*****
Pxx
Function
Value
Description
Heating
After installing the app and creating an account:
1
Heating/Cooling
Selection
P01
Cooling
TPI for Underfloor
Heating
TPI UFH
STEP 1 - DOWNLOAD ENGO SMART APP
TPI RAD TPI for Radiators
Select the Wi-Fi network in
which the thermostat will
operate and enter the password
of this network.
Wait for the app to configure
the thermostat with the
selected Wi-Fi network.
Press and hold the – & + buttons for approx. 5 seconds
until the display shows„SY”. Then release the keys.
Download the ENGO Smart app from Google Play or Apple App
Store and install it on your smartphone.
TPI for Electrical
Heating
TPI ELE
On your mobile device, make sure the ENGO Smart has
access to permissions (Location, Bluetooth, Nearby devices).
Then turn on Bluetooth and Location. Connect to 2.4GHz
Wi-Fi network to which you want to assign the device
5
HIS 0.4
HIS 0.8
HIS 1.2
HIS1.6
HIS 2.0
HIS 3.0
HIS 4.0
SPAN +/-0,2°C
SPAN +/-0,4°C
SPAN +/-0,6°C
SPAN +/-0,8°C
SPAN +/-1,0°C
SPAN +/-1,5°C
SPAN +/-2,0°C
Control
algorithm
P02 (in Cooling mode
TPI algorithm is
unavailable)
10
9
HIS 0.4
2
The thermostat started to send a signal to find the
receiver and started the countdown with the number
300 (sec). The pairing process may take up to 300 seconds.
If the thermostat
indicates wrong
temperature, you
can correct it by
3.5°C
Connect the receiver to the power supply.
When first powered up, the red led will start flashing, which
means that devices are ready to be added to the application.
5
Go to step (adding devices in the app). If the red LED on
the receiver is not flashing, proceed with the next steps.
6
Go„DONE”.
The thermostat has been
installed and displays the
main interface.
Offset
P03
-3.5°C to
+3.5°C
0°C
NO
temperature
11
Normally Open
type of relay
NO
NC
STEP 2 - REGISTER THE NEW ACCOUNT
P04
Relay type
3
Normally Closed
type of relay
To register a new account, please follow the steps below:
When the orange LED stops blinking,
the devices have been paired on a new frequency.
Minimum heating /
5°C - 20°C cooling temperature 5°C
that can be set
Minimum
setpoint
P05
P06
1
2
7
8
Maximum heating /
20,5°C -
Maximum
setpoint
When the blue LED on the receiver will light up, it means
the device has been correctly added to the application and is
now connected to the Internet.
cooling temperature 35°C
35°C
5 sec.
5 sec.
that can be set
Press and hold the – & + buttons for approx. 5 seconds
until the display shows„PA”. Then release the keys.
The pairing mode will start.
NO
Function disabled
Function enabled
P07
PIN Code
NO
000
NO
PIN
4
After successfull pairing Thermostat displays the main
operation ”End”message
will be displayed.
P08 PIN Code value
000-xxx
NO
User PIN
screen, icon ” ” .
Require a PIN to
unlock the keys
Function disabled
P09
CLR
every time
(Active when
P07=PIN)
PLEASE NOTE!
YES
Function enabled
Click„Register”to create
new account.
Enter your e-mail
A globe icon appeared on the LCD.
If the devices remain unpaired after 10 minutes (e.g. no
antenna icon on the controller, the receiver does not respond
to the heating signal from the controller), the pairing process
must be repeated, taking into account the distances between
the devices, obstacles and interference.
address to which the
verification code will
be sent.
NO
No
Restoration default
value
The Thermostat counts the time back (180s).
NO
Pairing process with the receiver
YES
Yes
3
4
5
6
PLEASE NOTE!
THERMOSTAT IS ALREADY PAIRED WITH THE RECEIVER!
1
2
3
Factory reset
To RESET Thermostat to factory settings, hold down the – and
+ buttons until the FA message appears.
Then release the keys. Thermostat will restart, restore default
factory settings and displays the home
Installer settings
To enter installer parameters press and hold button for
3 seconds.
SET
screen. The device will be removed from the app you will need
to add it again.
If you want to re-pair the receiver and thermostat with each
other and then add it to the application, make sure that the
receiver is disconnected from the power supply, and the
switches on it are in the ON and AUTO positions. Then connect
the receiver to the power supply and wait a few seconds.
Next, move the left switch to the OFF position and back to the
ON position with a quick motion. The orange LED will start
blinking, which will confirm that the receiver has entered the
pairing mode.
SET
Enter the verification
code received in the email.
Remember that you
only have 60 seconds to
enter the code!
Then set the login
password.
In the app, select:
„Add Device”.
After finding the
thermostat, go„Add”.
3 sec.
Use – or + button to move between parameters. Enter
the parameter by . Edit the parameter using – or +.
Confirm the new parameter value with the
After the reset, the devices are still paired.
button.
| General | Details |
|---|---|
| Name | ENGO E20i Series Wi-Fi Wireless Internet Thermostat User Guide |
| Make | ENGO |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.31 MB |
(1 votes, average: 5.00 out of 5)
Loading...
ENGO E55W230WIFI Wi-Fi Thermostat User Guide
ENGO EONEBATW, EONEBATB Internet Controlled Thermostat User Guide
ENGO E901 Programmable Wired Thermostat User Manual
ENGO E901 Wireless Internet Thermostat User Manual
ENGO EASY230W Wired Thermostat User Guide
ENGO EASYBATB Wired Battery Thermostat User Guide
Engo EFAN-230 Zigbee Smart Thermostat Owner’s Manual
ENGO CONTROLS EFAN-24W, EFAN-24B Fan Coil Thermostat User Guide
HBX THM-0100 Programmable Thermostat Instruction Manual
AIRZONE Blueface Zero Thermostat User Manual
APATOR TH 480 Bi Metallic Thermostat Instruction Manual
Roth VVS-nr. 466397.058 Softline Standard Room Thermostat Instruction Manual
SEELEY Ducted Gas Heater with MagiQtouch Controller or Manual Thermostat Owner’s Manual
sygonix 2997033 Wi-Fi Radiator Thermostat Instruction Manual
SALUS BTR230 Room Thermostat User Guide
Immax neo LITE 07534L Smart Thermostat for Underfloor Heating User Manual
homematic IP TRV-E-A Monday Radiator Thermostat Instruction Manual