Danfoss RA 2000 Radiator Thermostat Installation Guide
Installation Instructions
Radiator thermostat RA 2000, universal model
Installation, temperature setting, limitation and blocking, theft protection
Installation
The remote sensor must not
be in a drafty location or be
covered. Do not install above a
heat source. Attach the sensor
To remove the thermostat turn bracket to the desired location.
the base counter-clockwise.
This will also reset the the
snap-action mechanism when
an audible "click" is heard.
Pull out the required length of
capillary tube and secure to
the sensor as shown. Push the
sensor onto the base.
Remove the valve cover.
Check that the thermostat is
set at the factory setting of 5.
Push the thermostat firmly
onto the valve until an au-
dible "click" is heard.
Mounting thermostat with built-in sensor
Mounting thermostat with remote sensor
Temperature setting
guidelines only. The actual room tem-
perature will depend on structural fac-
tors affecting the thermostats, location,
etc.
The required room temperature is
obtained by turning the thermostat
knob. The numbers on the dial cor-
respond to the approximate tem-
peratures of the scale.
45 49
79,5 14
57
17
63
68
73
23 26
79 82°F
28°C
20
l
1
2
•
•
3
•
•
4
5
l
= Frost protection setting
The temperatures indicated are
Limiting and blocking the setting range
Upper limit setting (max. setting)
Lower limit setting (min. setting)
Locking setting
Example: Required max. value = “4”
Set thermostat at “4”
-
Example: Required locked value = “3”
- Set thermostat at “3”
Example: Required min. value = “2”
- Set thermostat at “2”
- Remove a pin from the bottom of the
thermostat with a screwdriver and
mount it under the diamond mark on
the knob (between setting positons 1
and 2).
- Remove both pins from the the ther-
mostat.
- Place one pin under the diamond mark
and the othger pin under the triangle
mark.
- Remove a pin from the bottom of the
thermostat with a screwdriver and
mount it under the triangle mark on
the knob (between setting positons
2 and 3).
Theft protection
Remove the cover and install the theft
protection button, code 013G5245
without pushing it all the way in.
Once the thermostat is mounted on
the valve, push in the theft protection
device. The thermostat cannot be
removed.
To remove the theft protection use
screwdriver 013G1236 and screw into
the hole (1). Pulled out until the stop is
reached (2).
DKCD
VI.51.T6.12 1/2003
| General | Details |
|---|---|
| Name | Danfoss RA 2000 Radiator Thermostat Installation Guide |
| Make | Danfoss |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.37 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Danfoss RET-MD Electronic Intelligent Dial Setting Thermostat Installation Guide
Danfoss VICUQ24M Icon Programmable II Room Thermostat Installation Guide
Danfoss MBC 8000, MBC 8100 Heavy Duty Thermostat Installation Guide
Danfoss UT 72-UT 73 Universal Thermostat Installation Guide
Danfoss ECtemp 530 Electronic Thermostat Installation Guide
Danfoss 014G0251 Eco Radiator Thermostat User Guide
Danfoss 014G0013 Z Wave Radiator Thermostat Installation Guide
Danfoss RET230P Electronic Thermostat Instruction Manual
Danfoss TP7000 Range Electronic 7 Day Programmable Room Thermostat Installation Guide
Danfoss RET1000 Series Electronic Thermostat User Guide
Danfoss RA 2000 Manual: Questions and Answers
Where is the remote sensor installed on Danfoss RA 2000?
Attach the sensor bracket to the desired location. Pull out the required length of capillary tube and secure it to the sensor as shown. Push the sensor onto the base. Installation Guide, p. 1
How do I install Danfoss RA 2000 onto a heating valve?
Remove the valve cover and verify the thermostat is at factory setting 5. Push the thermostat firmly onto the valve until you hear an audible click.
- Remove the valve cover.
- Check that the thermostat is set at the factory setting of 5.
- Push the thermostat firmly onto the valve until an audible click is heard. Installation Guide, p. 1
Can I install the remote sensor above a heat source on Danfoss RA?
No. The remote sensor must not be installed above a heat source, nor in a drafty location or covered. Installation Guide, p. 1
What is the factory setting on Danfoss RA 2000?
Setting 5. Installation Guide, p. 1
More Danfoss thermostat manuals
WarmlyYours UTN5-4999 Thermostat User Guide
SHANGHAI TR9B Ultra Large Colorful Screen Capacitive Touch LCD Smart Thermostat User Guide
HomeHome App ESP01V2 Mini Relay Thermostat Installation Guide
GENERAL ARUNA 301S Digital Room Thermostat User Manual
EMSQ22 Daikin ONE Lite Smart Thermostat User Manual
tecnoswitch Raffaello 230 TE215VU Electronic Recessed Thermostat User Guide
Expert4house BAC-1000ALNE Room Thermostat User Guide
EpheyFIF WITH3 Wireless Gas Boiler Thermostat User Guide
Puravent CFST Frost Thermostat Installation Guide
BOSCH II 230V Room Thermostat Instruction Manual