4512673 Heatit ZM Thermostat 16A User Guide

1

2

Wire the device as illustrated below.  

The product allows for wiring of cables with cross  

section of up to 1X2.5mm2  

LED PATTERNS  

HEATIT ZM  

THERMOSTAT  

16A  

GREEN  

RED  

Successful  

Unsuccessful  

Read the full manual at:  

manuals.heatit.com  

Quick Guide  

01.09.21 Ver 2021-A  

Last  

Load  

TECHNICAL DATA  

Protocol  

Chip  

Z-Wave  

Z-Wave 700 chip  

NTC  

L

N

Rated voltage 230VAC 50Hz  

Max load 3600W 165A  

Power Consum. <1W  

Ambient temp. 5°C to 40°C (-30°C to 70°C storage)  

Configuration button  

N

Power connection (Neutral) 230VAC.  

Output. Load needs to be connected between  

O and Neutral.  

Humidity  

Range RF  

IP Code  

Max 95% RH  

Min. 40 meters  

IP 20  

O

L

L

Power connection (Live) 230VAC.  

Power connection (Live) 230VAC.  

Size (DxWxH)  

46 x 45 x 25mm  

NTC10K NTC Temperature sensor.  

Approvals  

Z-Wave Plus V2,  

INTRODUCTION  

CE,  

NTC10K NTC Temperature sensor.  

Heatit ZM Thermostat 16A is an electronic  

thermostat for electrical floor heating designed  

for inwall installations. The thermostat allows you  

to control your electrical heating through your  

Z-Wave network. The module is equipped with a  

16A single pole relay. The thermostat requires you  

to connect an external sensor which is included  

with the device. The device can withstand a max  

load of 16A at 230VAC.  

EN 60669-1:2018,  

ADD/REMOVE  

EN 60669-2-1:2004 + A1:2009,  

EN 60669-1:2004/A12:2010,  

EN 60669-2-5:2016,  

1. Set the primary controller to add mode  

(secure/non-secure).  

2. Press the configuration button 3 times in rapid  

succession.  

IEC 965-2-1, EN 62479:2010,  

ETSI EN 301 489-3 V2.1.1(2017-03),  

ETSI EN 300 220-2 V3.1.1(2017-02),  

RoHs 2002/95/EG,  

3. The device LED will flash green when the  

adding procedure has been successfully  

initiated.  

WEE 2002/96/EC  

When the device has been included in the home  

automation system, the LED will stay green for  

3 seconds. The device is now ready for use with  

default settings.  

The device is maintenance-free. Indoor use only.  

STATEMENT REGARDING PRODUCTS  

FROM MULTIPLE MANUFACTURERS  

Please read this before installation  

This device may be used with all devices certified  

with the Z-Wave Plus™ certificate and should  

be compatible with such devices produced by  

any manufacturer. Every primary controller is  

different depending on the manufacturer, their  

target audience and intended use/application.  

Please review the functionalities implemented  

by the primary controller you intend to use with  

our Z-Wave Plus certified device to ensure that  

it provides the necessary controls to take full  

advantage of our product’s capabilities.  

If the adding process was unsuccessful, the LED  

will show a red light for 3 seconds. Please perform  

a ”remove device”process and try to add again. If  

the LED goes red again, please see the full manual  

for more information regarding adding, removing  

and factory reset.  

Adding/removing mode is indicated on the  

device by a flashing green lights. This lasts until  

timeout occurs after 90 seconds, or until the  

device has been added/removed from the  

network.  

INSTALLATION  

Heatit Controls AB can not be held liable for typographical  

errors, other errors or omittances in our information.  

Product specifications may change without further notice.  

All electrical installations must be carried out by a licensed  

electrician. The product must be installed in accordance  

with national building codes and our installers manual.  

Installation must be done by a qualified electrician  

in accordance with national building codes.  

Before installation, disconnect the power to the  

device. During installation of the device, power  

to the device must be disconnected AT ALL TIMES!  

NB! When the device is removed from the  

gateway, the parameters are not reset. To reset the  

parameters, see the full manual.  

Heatit Controls AB  

l

Läkarvägen 4, 454 31 BRASTAD, SWEDEN  

post@heatit.com – www.heatit.com  

Phone: +47 61 18 77 77  

l

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	4512673 Heatit ZM Thermostat 16A User Guide
Make	HEATIT
Language	English
Filetype	PDF (Download)
File size	0.14 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• HEATIT

4512673 Heatit ZM Thermostat 16A User Guide Overview

Summary of Contents

• Page 1: Wire the device as illustrated below. The product allows for wiring of cables with cross section of up to 1X2.5mm². Heatit ZM Thermostat 16A is an electronic thermostat for electrical floor heating designed for in-wall installations. The thermostat allows you to control your electrical heating through your Z-Wave network. The module is equipped with a 16A single pole relay. The thermostat requires you to connect an external sensor which is included with the device. The device can withstand a max load of 16A at 230VAC. The device is maintenance-free. Indoor use only. All electrical installations must be carried out by a licensed electrician. Installation must be done by a qualified electrician in accordance with national building codes.
• Page 2: Koble til ledningene som vist på tegningen under. Maks diameter for tilkoblede kabler er 1x2,5mm. LED indikasjonmønster. Heatit ZM. Termostat. Maks belastning 3600W 16A. Omgivelsestemperatur 5°C til 40°C (-30°C til 70°C lagring). Produktet trenger ikke vedlikehold. Kun for innendørs bruk. Produktet skal installeres av autorisert installatør i henhold til norske bygg-forskrifter. Heatit Controls AB tar forbehold om typografiske feil, andre feil eller mangler i vår informasjon.