Home > Remotec > Remotec REMEZTRVV01 Z Wave Thermostat User Guide

Remotec REMEZTRVV01 Z Wave Thermostat User Guide

6

Remotec

Remotec Thermostat Z-Wave

SKU: REMEZTRVV01

Quickstart

This is a secure Z-Wave Device for Europe. To run this device please insert fresh 2 * AA batteries. Please make sure the internal battery is fully charged.

1. Add TRV DSK into the primary controller SmartStart Provisioning List (If you don’t know how to do this, refer to its manual, DSK usually print on the main

body).

2. Remove the battery from the TRV. A few seconds later, repowered in the TRV.

3. The TRV will send “Z-Wave protocol Command Class” frame to start SmartStart Inclusion.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer,

distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this

equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and

every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is

not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified

Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this

device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level

of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

The TRV based on Z-WaveTM Slave library of V7.16.03. This TRV integrated Z-Wave communication module to connect with Z-Wave gateway.

The TRV can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications.

The TRV is a security Z-Wave device (S0/S2), so a security enabled controller is needed for take full advantage of all functionally for the TRV.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do

this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended

to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.

In “OF” state, press and hold rotary plate for at least 5 seconds and release when the screen will blink “OF”. When the reset is successful, the screen will show

“OF” in solid for 2 seconds then turn off. And TRV will reset itself to factory default by sending a “Device Reset Locally Notification” to gateway.

Safety Warning for Batteries

The product contains batteries. Please remove the batteries when the device is not used. Do not mix batteries of different charging level or different brands.

Installation

IMPORTANT: Please include your TRV to the network (refer to 4.1) before doing the installation. Below is the installation process:

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	Remotec REMEZTRVV01 Z Wave Thermostat User Guide
Make	Remotec
Language	English
Filetype	PDF (Download)
File size	0.27 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Comments are closed.

Remotec Instructions & User Manuals

Get the free PDF manual for the Remotec REMEZTRVV01 Z Wave Thermostat User Guide and access setup steps, usage instructions, and troubleshooting tips. 👉 View online or download now to keep your thermostat running smoothly!

Remotec REMEZTRVV01 Z Wave Manual: Questions and Answers

Remotec REMEZTRVV01 Z Wave specifications

Batteries	*2 AA**
IP rating	IP IP20
Dimensions	0.0500000x0.1000000x0.0500000 mm
Radio frequency	Europe - 868,4 Mhz

Full specifications, page 5

What is the difference between inclusion and exclusion on Remotec REMEZTRVV01 Z Wave?

Inclusion adds the device to a Z-Wave network; exclusion removes it. Both use the same button action but with different controller modes. User Guide, p. 1

What does the antenna icon mean on Remotec REMEZTRVV01 Z Wave?

The antenna icon lights on when inclusion is successful, indicating the device is connected to the Z-Wave network. It turns off during exclusion. User Guide, p. 2

Can I reset Remotec REMEZTRVV01 without connecting it to a Z-Wave controller?

Yes. In OFF state, press and hold the rotary plate for at least five seconds until the screen blinks OFF. Release when it blinks. After two seconds the screen shows solid OFF then powers down, and the device resets to factory default. User Guide, p. 1