Rayotec Coloursense Wi-Fi Thermostat Instruction Manual
WiFi Pairing
1. Search for "Smart life" from Google Play
Setting the time and date: If you pair the thermostat with the Smart Life app it will automatically
2. Open the Smart life app and click on the
+ symbol in the top right of the screen,
on the left hand side select “Small Home
Appliances” and then scroll down the list
and click “Thermostat (Wi-Fi)”
set the time and date. If you wish to change it manually you can do this by clicking on the
tap the General” tab on the top, in this list tap on “Time Setting” and then click on the up and down
arrows next to the minutes and hours to change them. To change the date simply tap on the number you
wish to change and use the number pad to enter the correct date and press “OK” to confirm it. When you
have the correct time and date simply tap “Confirm” at the bottom to apply the changes.
button then
or App Store to install the app.
3. You will need to select your 2.4ghz WiFi
network and enter your password. If
your router is a newer model such as
BT home hub or Virgin Media box you
will need to change the router settings
to 2.4ghz.
4. On the next screen it will ask you to
power on and reset the device, this is
not needed for a new unit, click “Next”
on the next 3 screen options until you
see 2 options “Blink Slowly” or “Blink
Quickly” Leave this up for now.
Changing heating modes: You can change between Automatic programming, Manual control and
Holiday mode. To do this click on the
button then tap the “General” tab on the top, in this list tap on
“Mode setting” then select your preferred option and tap confirm. Choose “Manual control” if you don’t
want the heating to be controlled by a schedule.
Applying child lock: To do this click on the button then tap the “general” tab on the top, in this list
5. At this point, turn on the thermostat----
6. When the display on the thermostat is
showing “WiFi network connect in
progress” click the icon on the app for
“Blink Quickly” and the thermostat will
automatically pair up.
tap on “Lock” and select “Yes”. To disable child lock hold down the
arrow for a few seconds.
Press
and then select “General”,
Default password is “123456”
Select “Network Connect “ then press
“Yes”
Advanced Settings Menu Defaults
Access by tapping the
button then Advanced tab
Troubleshooting
Screen not responding to button presses:
Check that the child lock is not on, this can be seen by a closed padlock in the top right corner. To remove
Item
Parameter
Default
Temperature compensation
-9~+9
-1
1
Start temperature hysteresis (tolerance)
0.5~2.5
child lock hold the arrow until the icon changes to an open lock.
External sensor protection temperature 1~9
hysteresis (tolerance)
2
Heating icon flashing:
High temperature protection value
Low temperature protection value
Set the upper temperature limit
Set the lower temperature limit
Password setting
20-70
27
This is an indication that the floor probe is reading the temperature too high and the upper limit
protection of 27c has kicked in and is telling the thermostat to stop calling for power. The most common
cause is the location of the floor probe being too close to the heating elements. Check that there is no
obstruction on the floor stopping the heat getting out, if no obstructions are there then move the floor
probe away from the heating cables.
1-10
20-70
1-10
5
35
5
123456
Half lock
Thermostat not powering on:
Child lock
Half lock ,full lock
The most common thing to cause this is incorrect wiring, historically there has been cases where the
incoming power cables were wired into the heating mat terminals which meant no power was getting to
the unit. First check that the cables are in the correct ports, if they are then check that the incoming
power cables are live.
Sensor type (Built in = Air, External = Floor Built in /external /internal Internal and
probe)
and external
1-60 min
10-20
external
Window opening setting time
Window opening setting temperature
Holiday mode time
Holiday mode temperature
Reset
10
10
1
Thermostat not connecting to the app:
This can be caused by the router being stuck in 5ghz output, check your router settings and ensure that it
1-30 days
5-35
is set to 2.4ghz output as the thermostat cannot connect to 5ghz.
15
No
No
Yes/No
For further assistance and step by step guides check out our website at
Heating time clear
Yes/No
| General | Details |
|---|---|
| Name | Rayotec Coloursense Wi-Fi Thermostat Instruction Manual |
| Make | Rayotec |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.18 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Rayotec PERGARP0DCN6YB3I Wi-Fi Thermostat Instruction Manual
Rayotec Freedom Wi-Fi Thermostat Instructions
Danfoss BD271136569160en-010102 Electronic Radiator Thermostat Owner’s Manual
Honeywell Lyric T5 Wi-Fi Thermostat Installation Guide
COPELAND 1F95G-1235GC Humidity Universal Thermostat Instruction Manual
Munters RDT-5 Triple Phase Digital Thermostat User Manual
K nighaus Infrarot Thermostat Owner’s Manual
Roth Basicline Wired Thermostat Installation Guide
seitron TR D02B Wireless Digital Thermostat User Manual
EvenAir T21WF WiFi Thermostat User Manual
Honeywell Home X8S Smart Thermostat User Guide
Honeywell DT90A Digital Room Thermostat User Guide