Klima 825201 Intelligent Control Wi-Fi Underfloor Heating Thermostat User Manual

1

2

Left button:  

Push right button in main screen to go straight to Menu settings (2.4)  

Confirming a choice  

2.Temporary temperature:  

To temporarily override the temperature in the automatic  

program. The override will operate until the next automatic event.  

Select an option  

(

)

Right button:  

USER MANUAL  

3.Manual mode:  

Push left button in main screen to go straight to Mode functions (2.3)  

To get back to last screen or main screen(← or X )  

The thermostat runs continuously according to the set temperature.  

USER MANUAL  

Model: MIC2+ WIFI  

Always go back to the main screen after making changes.  

4.OFF:  

Explanation of LED colours / signals :  

Manually turn off all functions of the thermostat. When you want to reactivate  

the thermostat, just select the mode you want.  

Heating  

Red:  

System operation（standard or Costum)  

Green：  

Installation  

Red light flashing on and off: Sensor fault  

5.Anti-frost mode:  

1.Check if the power is off. Remove the display frame by pushing a non sharp  

instrument (for example the point of a ballpoint pen) carefully in the square hole  

underneath the thermostat.  

Range is set from 41°F to 59°F(5°C -15°C） in this mode. This mode is used  

when you want to keep your room at a lower temperature when you are on  

vacation.  

2.Connection schedule:  

L/N lead : Connect the power cord using the terminal block.  

L1/N1 lead : Use a terminal block to connect the load line(Max 16A).  

S1/COM/ : Connect the floor sensor.  

Pilot : Connect the pilot to L when the pilot wire function needs to be enabled.  

WARNINGS: 1.Disconnect the main power supply before wiring.  

Installation needs to be done by a qualified electrician in accordance with  

all current wiring and building regulations. 2.Electric floor heating cable/  

mat must be in accordance with the supply voltage.The terminals are  

designed to handle a cross-section of wire measuring 12-22AWG.  

6.Timer:  

Date  

Time  

Use this mode when you are on holidays etc.The thermostat will be off for the  

chosen period. After this period, the thermostat will return to the standard or  

the custom time settings.  

Measured Temp  

Mode  

Menu  

7.Slow heating:  

Menu/Confirm  

LED  

To be used for new floors only. The thermostat will slowly raise the  

temperature of the floor over a 20 day period. After this period the thermostat  

automatically starts the standard or the custom time programme. If you need  

to stop or restart the slow start up mode, press the left button.  

Mode/get back  

3.The display frame and the cover frame can be removed. Position the  

thermostat and install onto the back box (not supplied). Place the display frame  

back into position by pushing it softly.  

Up/Down/Scroll  

Menu selection  

1.Temperature settings:  

POWER  

You can change the programmed temperature (comfort or set back ).  

Attention: In the case of floor heating, it is not necessary to program  

the setback temperature.The setback temperature is controlled by the  

thermostat automatically.  

Start up wizard  

Language  

Date  

1

2

Units  

3

-year;  

program the current year.  

-make your language choice.  

This is the first question in the  

start up menu.  

- Clock;  

choose 12 or 24 hour clock  

time (am/pm) .  

01  

02  

2.Programming:  

The comfort temperature and times can be changed in this menu.  

Standard program:  

-month;  

program the current month.  

- Temperature;  

choose °C or °F scale .  

-day number;  

program the current day.  

Monday--Sunday  

Period 1  

Period 2  

06:00-09:00 23℃  

17:00-22:00 23℃  

Time  

Intelligence  

Heating system  

4

5

6

Custom week program: Push the button to confirm the function ‘program’.  

You enter the screen with the standard settings schedule.  

-Floor heating or different  

heating system. If you choose  

a different heating system the  

question will be whether the  

system needs to function on  

the internal room sensor or  

external sensor.  

-program time;  

program the actual clock time  

-This function enables the  

thermostat to calculate when  

it needs to switch on so that  

the required temperature is  

reached at the set time.  

04  

03  

Press  

Press  

Press  

Press  

button,‘standard’ appears on the display.  

button,‘standard’ is selected.  

button select ‘custom’. confirm this with  

button.  

/

button return to the screen of programmed times.  

Note:  

Now you can confirm the symbol by pushing the right button.  

You can adjust one or two periods a day. If you want to program the same time  

periods on different days, use the easy copy and paste function.  

According to user preference,  

the circular and square outer  

frame can be replaced.  

Summary  

Surface material  

Temp.to control  

9

7

8

-If you choose floor heating.  

Wood or other. If you choose  

other, the question is asked if  

there is a floor sensor installed  

-Containing the current  

settings.  

-Floor or room sensor.  

05  

3.Consumption:  

If you choose floor heating,  

we advise you to control the  

floor temperature by using  

the floor sensor.  

The thermostat calculates the average time it has been switched on allowing  

you to monitor your energy consumption. The total switched on time is by  

percentage (%) shown over the last 30 and 365 days.  

Calculate consumption:  

30 days: 24 hours x 30 days x total installed power x % = energy consumption  

365 days: 24 hours x 365 days x total installed power x % = energy consumption  

Example:  

The thermostat gives a percentage of 26% over 30days.  

The power installed in the floor is 700 Watt.  

24 hours x 30 days = 720 hours.  

720 hours x 0.7 kW = 504 kWh  

26% of 504 kWh = 131 kWh.  

Supply voltage:  

Load:  

85-265 VAC 50/60 Hz  

max.16 A (resistive load)  

11 Overview wizard  

Slow heating  

Temperature  

12  

10  

-Containing the selected  

heating periods according the  

standard program.  

-It is possible to choose this  

option (Ref Mode selection  

point 7 slow start up).  

-Program the comfort temp-  

erature of your choice for a  

heating period. Standard  

temperature for a “different  

heating system is program-  

med at 21 degree Celsius and  

23 degree Celcius for a floor  

heating system.  

Setpoint range:  

Temperature range:  

Cover:  

+5 to +40°C / +41 to +104°F  

+5 to +45°C / +41 to +113°F  

IP21  

Approvals:  

CE/UKCA  

Floor sensor type:  

NTC B=3740 12k  

4.Child lock:  

The thermostat is locked with this function.Mode and menu settings cannot  

be used.To switch the child lock function on or off, push the right key and  

hold it for a few seconds. When the child lock is switched on, a padlock  

appears on the display.  

Operation and LED  

Keys operation：  

←

Mode selection  

5.Information:  

1.Automatic mode:  

Middle buttons:  

Gives information about the current software and hardware version of the  

thermostat.  

Adjustment up and down (±or  

To scroll through settings  

)

According to the weekly program, the thermostat automatically adjusts the  

set temperature operation.  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	Klima 825201 Intelligent Control Wi-Fi Underfloor Heating Thermostat User Manual
Make	klima
Language	English
Filetype	PDF (Download)
File size	0.5 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• klima

Klima 825201 Intelligent Control Wi-Fi Underfloor Heating Thermostat User Manual Overview

Summary of Contents

• Page 1: Left button: Push right button in main screen to go straight to Menu settings. Temporary temperature: To temporarily override the temperature in the automatic program. Manual mode: The thermostat runs continuously according to the set temperature. OFF: Manually turn off all functions of the thermostat. Anti-frost mode: Range is set from 41°F to 59°F in this mode. Timer: Use this mode when you are on holidays; the thermostat will be off for the chosen period. Slow heating: The thermostat will slowly raise the temperature of the floor over a 20-day period. Programming: The comfort temperature and times can be changed in this menu. Consumption: The thermostat calculates the average time it has been switched on allowing you to monitor your energy consumption. Child lock: The thermostat is locked with this function; mode and menu settings cannot be used.
• Page 2: If you are in the process of networking, the device cannot be discovered. You can press + and - buttons on the thermostat at the same time to switch the wifi connection mode. With this function you can change settings related with the operating of the thermostat. The thermostat will change summer and winter clock change automatically. The thermostat provides advanced settings to suit a range of special situations which are normally set by a technician during initial installation. The thermostat has a self thinking and adaptive system. This function only works when room sensor or both sensors is selected. All parameters are restored to default value. The setback mode is when the thermostat ‘sets back’ to a lower temperature during the off time periods. Some floor coverings must be limited at a certain maximum temperature.