Home > JABLOTRON > JABLOTRON TP-98TX Wireless Thermostat Instruction Manual

JABLOTRON TP-98TX Wireless Thermostat Instruction Manual

2

Wireless Thermostat TP-98TX

common indoor residential

This thermostat can replace

TEMPERATURE SETTING

thermostat and is designed to be used with electric, gas or oil

heating system. The easy to read display shows the current room

Temperature and temperature adjustment is very simple.

The TP-98TX wireless thermostat is compatible with Jablotron’s

wireless receivers UC-222, UC-241 and UC-242. Radio

communication provides high reliability and allows for very easy

installation as well.

In the normal operation mode, the thermostat shows the room

temperature. To set a desired temperature:

•

Press

was set last time.

Hold ꢀor

ꢀor

button to view the previous temperature, which

•

button for about 3 seconds and the temperature

indicator will flash one time. Press

ꢀor

button to increase

or decrease the temperature setting. The unit will return to

normal operation mode automatically after 10 seconds with out

any button being pushed..

•

The programmed temperature range is from 5°C to 35°C.

The temperature span between the turn ON and OFF is 1°C. For

example, if the control temperature setting is 20°C, \the heater will

operate when the room temperature drops to 19.5°C and will be turn

off when the temperature rises to 20.5°C. When the thermostat is on,

the symbol Heater On is indicated.

When the temperature is above 40°C ‘HI’ will be shown on the

LCD and ‘LO’ will be shown when temperature falls below 0°C.

When the voltage of the battery is low, the LCD will turn off. In this

case, the batteries should be changed as soon as possible.

SPECIFICATIONS

Power Source:

two AAA 1.5V Alkaline batteries

0 - 40°C

±1.0°C

5 - 35°C

1°C

Temperature Measurement:

Temperature Accuracy:

Temperature Control:

Temperature Control Span:

Output On Delay:

20 seconds

Working frequency

Working distance

Coding:

433,92 MHz

up to 100 m (open area)

digital, each thermostat has

a unique floating code

-10°C to 50°C (non-condensing)

-30°C to 60°C

73.5 X 28.0 X 73.5 mm

Polycarbonate (PC)

90 g (battery not included)

INSTALLATION

The TP-98TX should be mounted in a dry indoor location. This

thermostat has been designed for easy installation. Choose a

mounting location about 1.5 meters above the floor, in an area with

good air circulation. Avoid places with drafts, dead air spots and

radiant heat from the sun or appliances. It should not be installed

close to any metal structure or other objects that may obstruct

radio signal transmissions.

Operating Temperature:

Storage Temperature:

Size:

Material:

Weight:

Can be operated according to ERC REC 70-03

•

Remove completely the front housing of the thermostat. (using

a screwdriver)

Drill two holes and insert the plastic dowels.

Attach the thermostat to the wall with the two screws.

Hereby, Jablotron Ltd., declares that this TP-98 is in compliance with

the essential requirements and other relevant provisions of Directive

1999/5/EC.

•

Note: Dispose of batteries safely depending on the type of the

batteries and local regulation. Although this product does not contain

any harmful materials we suggest you to return the product to the

dealer or directly to the producer after usage.

ENROLLING THE TP-98TX INTO THE RECEIVER

•

Slide the battery cover upward to open it.

Remove the batteries from the thermostat if there are any.

Enter the enrolling mode of the receiver unit (UC-222, UC-241,

UC-242) – See corresponding instruction manual

Place the batteries into the thermostat. Ensure the correct

polarity of the batteries.

•

The receiver will confirm successful enrollment

Push and slide the cover down to close it.

Note: Each UC-222 receiver can work with only one thermostat.

If the receiver unit was used with any other device before, reset its

memory before enrolling a thermostat.

Pod Skalkou 33

466 01 Jablonec nad Nisou

Czech Republic

Tel.: +420 483 559 999

fax: +420 483 559 993

Internet: www.jablotron.cz

TP-98TX Wireless Thermostat

1/2

MFR51405

https://manual-hub.com/

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	JABLOTRON TP-98TX Wireless Thermostat Instruction Manual
Make	JABLOTRON
Language	English
Filetype	PDF (Download)
File size	0.21 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Comments are closed.

JABLOTRON Instructions & User Manuals

Get the free PDF manual for the JABLOTRON TP-98TX Wireless Thermostat Instruction Manual and access setup steps, usage instructions, and troubleshooting tips. 👉 View online or download now to keep your thermostat running smoothly!

Jablotron TP-98TX Manual: Questions and Answers

Jablotron TP-98TX specifications

Power supply	two AAA 1.5V Alkaline batteries
Accuracy	±1.0°C
Operating temperature	-10°C to 50°C (non-condensing)
Storage temperature	-30°C to 60°C
Dimensions	73.5 X 28.0 X 73.5 mm
Weight	90 g (battery not included)
Radio frequency	433,92 MHz

Full specifications, page 1

What is the temperature control range for the Jablotron TP-98TX?

5°C to 35°C. Instruction Manual, p. 1

How do I set a desired temperature on the Jablotron TP-98TX?

Hold the temperature button for about 3 seconds until the indicator flashes once, then press to adjust.

Hold the button for about 3 seconds until the temperature indicator flashes one time.
Press the button to increase or decrease the setting.
The thermostat returns to normal mode automatically after 10 seconds of no button presses. Instruction Manual, p. 1