Innova B3V151 Electronic Thermostat User Manual
UnIT WITH TOUCHpAD COD. ECA844 - EWA844
Correct use of the remote control:
In heating function the symbols is alight with setpoint
ꢀ
• point the front of the remote towards the unit’s dis-
play, the buzzer will emit a beep and a message will
appear on the display to confirm that the command
has been enabled
higher than the room temperature.
3ꢀ2ꢀ5 Cooling only mode
• the maximum range to send commands is about 8
metres
To select the Cooling operation
► press
for about 2 seconds
To activate the touchpad
The lighted
symbol in the display area indicates
► keep the
key pressed for 2 seconds
that the Cooling function is activated.
The device dehumidifies and cools the room.
The text
appearing on the display.
The device turns on.
In cooling function the symbols is alight with setpoint
ꢀ
The preset set-point appears on the 3 digits
the display.
of
lower than the room temperature.
The control panel has its own memory, therefore no
ꢀ
3ꢀ2ꢀ6 Functioning in automatic mode
settings will be lost in case of shut-down or power out-
age (except ventilation). The button in question is used
to switch the appliance on and off for short periods.
To select functioning in automatic mode
► press the key
The symbol
on indicates that fan operation in
If you plan to keep the device out of service for a pro-
ꢀ
automatic mode.
longed time, remember to deactivate it by disconnect-
ing the power or removing the power plug.
The ventilation speed is set automatically.
ꢀ
3ꢀ2ꢀ2 Put in stand-by the control
3ꢀ2ꢀ7 Functioning in maximum mode
Toꢀputꢀinꢀstand-byꢀtheꢀcontrol
To select maximum mode operation
► press the
key for about 2 seconds
► press the key
The symbol
appears
The lighted
symbol on the display indicates fan
The control goes out.
operation in maximum mode.
The control panel has its own memory, therefore no set-
ꢀ
The ventilation speed is set automatically in maximum
ꢀ
tings will be lost in case of shut-down or power outage.
mode.
If you plan to keep the device out of service for a pro-
ꢀ
longed time, remember to deactivate it by disconnect-
3ꢀ2ꢀ8 Minimum mode operation
ing the power or removing the power plug.
To select minimum mode operation
Toꢀre-activateꢀtheꢀcontrol
► press the key
► press the
key for about 2 seconds
The symbol
on indicates that fan operation in
The device turns on and
appears
minimum mode.
In this mode the fan is set to minimum speed.
ꢀ
3ꢀ2ꢀ3 Set room temperature
This function can be excluded at any time by pressing
ꢀ
the button again.
To set the setpoint
► use the
keys to increase or decrease the
desired value
The displayed value change.
3ꢀ2ꢀ9ꢀ ꢀSetꢀtheꢀdirectionꢀofꢀtheꢀairꢀflow
Toꢀcontrolꢀtheꢀairꢀflowꢀdirection
The adjustment range goes from 16 to 28 °C, with a
ꢀ
► press the key
resolution of 1 °C.
The symbol
lit on indicates the constant oscilla-
Out of range values from 5 °C and 40 °C are allowed,
ꢀ
tion of the air flow deflector
except in automatic mode. These value should be set
only for short periods of time.
Toꢀlockꢀtheꢀairflowꢀdirectionꢀagain
► press again the
The symbols
key
Do not set a temperature that is too low or too high is
ꢀ
goes off and the air flow deflector
harmful to health and is an unnecessary waste of en-
locks in position
ergy.
never force the flow deflector manually to move it.
ꢀ
In cooling and heating mode, the flap position is reset
ꢀ
3ꢀ2ꢀ4 Heating only mode
every hour to prevent the formation of condensation.
To select the Heating operation
► press
The symbol
enable.
The device heats the room.
for about 2 seconds
3ꢀ2ꢀ10 Set the key lock
on indicates the Heating function
Toꢀset-upꢀtheꢀkeyꢀlocking
► press both keys
for 3 seconds
The text
appearing on the display.
9
| General | Details |
|---|---|
| Name | Innova B3V151 Electronic Thermostat User Manual |
| Make | InnOVA |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.77 MB |

































