HELTUN HE-HT01 Heating Thermostat User Guide
DISASSEMBLY
1. To disassemble, ENSURE POWER IS SWITCHED OFF at the main circuit breaker AND THE LCD SCREEN IS BLANK.
2. To remove the HE-HT01 display unit grasp firmly at the bottom and pull backwards while tilting outwards until all tabs disconnect.
3. Remove screws from backplate and disconnect the wires by inserting a small Phillips-head screwdriver into the slot beneath each wire
and unscrewing to release.
Z-WAVE NETWORK
The HE-HT01 may be operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers. The HELTUN
HE-HT01 will act as a ‘repeater’for other devices regardless of manufacturer or brand to increase the reliability of the overall network.
Frequency Region
The Parameter
Modification is possible only while the HE-HT01 is in a ‘Non-Included State.’ While in an ‘Included State’, the Antenna icon
be shown at the bottom right corner of the LCD screen and modification of this Parameter will be disabled. To navigate through the
1
(“ Eg”) allows you to manually change the Z-Wave frequency which is mandated in your geographical region.
will
different values, use the Plus (+) and Minus (–) buttons. After the Frequency Region has been selected, hold the Clock
save the Parameter value and reboot the device for the new settings to take effect.
button to
Security
S0, S2 unauthorized, and S2 authorized Inclusion Modes are supported. If you use the S2 authorized Inclusion Mode the security key
should be used during the inclusion process. The Security Key is printed on a card located with this quick start guide and also on the
HE-HT01 backplate (see Figures 9 & 10).
Note: Be sure to save this key. Without the key, it is impossible to perform an Inclusion in S2 authorized mode.
SmartStart
SmartStart-enabled products can be added to
a
Z-Wave network by scanning the Z-Wave QR Code shown on the product with
gateways/controllers that provide for SmartStart inclusion. In this case, no further action will be required and the SmartStart product will
be added automatically within ten minutes of being turned on in the vicinity of a network.
To add the HE-HT01 to the Z-Wave network using SmartStart:
1.
2.
3.
4.
5.
Set the main controller in Security S2 Authenticated “Add Mode”.
Input the thermostat DSK to the controller (or scan the QR code).
Power on the device.
Wait for the adding process to complete.
Successful adding will be confirmed by displaying the Antenna with signal strength bars
of the main screen.
icon in the bottom right corner
Note: The device security code (DSK) and SmartStart QR code are printed on the HE-HT01 back panel plus on the included Security Card
(see Figures 9 & 10).
| General | Details |
|---|---|
| Name | HELTUN HE-HT01 Heating Thermostat User Guide |
| Make | HELTUN |
| Language | English |
| Filetype | PDF (Download) |
| File size | 1.55 MB |
(1 votes, average: 5.00 out of 5)
Loading...
HELTUN Fan Coil Thermostat HE-FT01 User Manual
HVAC Electrical Heating Thermostat M5.XX Installation Guide
HITACHI ATW-RTU-11 Wireless Thermostat Instruction Manual
PRO1 T771 Programmable Electronic Thermostat Instructions
Wengart TP808 Low Voltage Thermostat User Guide
tekmar T-560 Touchscreen Thermostat User Manual
BEOK BOT306RF-WIFI Thermostat Owner’s Manual
ENGO CONTROLS E10-B Wi-Fi Thermostat User Guide
OSCAR OS20 LCD Thermostat Instruction Manual
EUROTRONIC SPIRIT ZigBee Energy Saving Thermostat User Guide
expert4house BHT-8000 Heating Thermostat User Guide