GLOBAL CEG Series Convector with Thermostat Instruction Manual

1

OPERATING  

MAINTENANCE  

INSTRUCTIONS  

INSTALLATION  

INSTRUCTIONS  

INSTRUCTIONS  

-

-

-

The heater must be properly installed before it is used.  

Turn the power on at the circuit breaker panel.  

Electronic thermostat: Set the thermostat temperature at the  

wanted room temperature  

1- Once a year, remove the front panel and use a vacuum cleaner  

to remove the dust accumulation inside the heater and through  

openings of the front panel.  

CAUTION: Use supply wires suitable for 90 °C (194 °F).  

- For bathroom use, the heater must be installed so that  

switches and other controls cannot be touched by anyone  

in the bath or shower.  

1 800 463-7043 • www.globalcommander.ca  

INSTALLATION INSTRUCTIONS  

Convector “CEG” Series  

2- Cleaning should be done while the heater is disconnected from  

the main service panel. Wait until the housing and heating  

element cool before performing maintenance.  

3- Replace the front panel before energizing.  

4- Any other servicing should be performed by a qualified  

technician.  

CONTROL:  

SURFACE WALL MOUNTING;  

1- Locate approximately the power supply leads behind the  

planned location of the heater. Recommended clearance  

below heater base to floor is 4 in. (102 mm) minimum.  

Allow 4 in. (102 mm) minimum clearance between sides  

of heater and any adjacent walls. The leads shall be at the  

right of the wall bracket.  

Model with built-in electronic thermostat:  

The electronic thermostat shall keep the room temperature in a range  

of ± 1 °C (± 2 °F) unless the room is not well insulated or the heater  

is too or not enough powerful for the room.  

WARNING  

When using electrical appliances, basic precautions should always be taken  

to reduce the risk of fire, electrical shock and injury, including the following.  

WARRANTY  

Model without control:  

2- Lean the bottom of the wall bracket on the floor and mark  

with a pencil the height desired (of the heater bottom)  

using the wholes with inches written on the side.  

3- Secure wall bracket with the 4 screws supplied. The bottom  

of the key holes shall be in line with the previous marks.  

Triangle mark on horizontal bar is the center of the heater.  

Before installing wall support, align center of heater with  

support center mark and make sure the heater sides are at  

least 4 in. (102 mm) from any adjacent walls.  

Please refer to the specification sheet at www.globalcommander.ca.  

Maintain room temperature by a line-voltage wall thermostat  

approved for residential heating. Even if it is not mandatory, an  

electronic thermostat gives better performance than a conventional  

thermostat.  

Read carefully these instructions before installation, operation of the  

heater. Failure to adhere to the instructions could result in fire, electric  

shock, serious personal injury, and death or property damage. Review  

frequently for continuing safe operation and instruction of future users,  

if necessary.  

IMPORTANT  

1- Read all instructions before installing or using this heater.  

2- This heater is hot when in use. To avoid burns, do not let bare skin  

touch hot surfaces. Keep combustible materials, like furniture, pillows,  

bedding, papers, clothes, and curtains at least 36 in. (915 mm) from the  

front of the heater and away from the sides.  

3- Extreme caution is necessary when any heater is used by or near  

children or invalids and whenever the heater is left operating and  

unattended.  

4- Do not operate any heater after it malfunctions. Disconnect power  

at service panel and have heater inspected by a reputable electrician  

before reusing.  

4- Untighten wire holder (for Loomex cable) and make  

electrical connections by having the heater the nearest  

possible to the electrical wire. For BX cable, remove one of  

the two knock-outs, install a connector (not furnished) and  

have 6 to 8 in. (15 to 20 cm) of free wire and get them out  

of the hole of the wire holder in order to make connections  

from outside. Do not forget to connect the green wire to  

ground wire in order to have a safe grounded heater.  

5- Once connections completed, place bottom T slots in the  

base part of support, and clip the upper side of the body in  

the upper U shape part of the support.  

TOP  

HAUT  

TOP  

HAUT  

Wiring Diagram:  

1

2

INSTRUCTIONS  

L1  

L2  

THERMOSTAT  

Model with built-in  

L1 Load 1 Load 2 L2  

electronic thermostat  

8

7

6

5

4

8

7

6

5

4

American version only  

up to 240V  

Mark  

the height  

desired  

6- Do not let the excess of the supply wire come in contact  

with the back of the heater, as well as any other object.  

7- Put the main power on.  

5- Do not use outdoors.  

6- To disconnect heater, turn off power to heater circuit at main disconnect  

panel.  

Wiring Diagram:  

Model without control  

CENTRE  

CAUTION:  

HAUT - TOP  

L1  

High temperature, risk of fire, keep electrical cords, drapery,  

furnishings, and other combustibles at least 36 in. (915 mm)  

from the front of the heater and away from the sides. To reduce  

the risk of fire, do not store or use gasoline or other flammable  

vapors and liquids in the vicinity of the heater.  

DETAIL A  

7- Do not insert or allow foreign objects to enter any exhaust opening as  

this may cause an electric shock or fire, or damage the heater.  

8- Do not block air intakes or exhaust in any way whatsoever.  

9- This heater has hot and arcing or sparking parts inside. Do not use it in  

areas where gasoline, paint, or flammable liquids are used or stored.  

10-Use this heater only as described in this manual. Any other use not  

recommended by the manufacturer may cause fire, electric shock, or  

injury.  

11-AMERICAN VERSION ONLY: Some models (up to 240V) include  

a visual alarm to warn that parts of the heater are getting excessively  

hot. If the light turns on, immediately turn the heater off and inspect  

for any objects on or adjacent to the heater that may have blocked  

the airflow or otherwise caused high temperatures to have occured.  

If no obstruction is visible, the heater must be checked by a quali-  

fied person. DO NOT OPERATE THE HEATER WHEN THE  

ALARM LIGHT IS ON.  

American version only  

up to 240V  

L2/N  

Center mark  

3

IMPORTANT  

Do not obstruct the front of the heater  

for at least 48 in. (1200 mm).  

OPTIONS:  

All heating equipment and options must be installed in  

accordance with local and national codes.  

Built-in relay:  

4

5

8

8

7

6

5

4

7

6

5

4

A

- Refer to the diagram included with the relay option for  

connections.  

- Refer to instructions supplied with the option for mounting.  

12-The thermostat should not be considered an infallible device in cases  

where maintaining a temperature is considered critical. Examples:  

Hazardous material storage, computer server room, etc. In these  

particular cases, it is imperative to add a monitoring system to avoid  

the consequences of a thermostat failure.  

4’’  

(102 mm)  

minimum  

4’’  

(102 mm)  

minimum  

4’’ (102 mm)  

minimum  

INS420-201402-03  

SAVE THESE INSTRUCTIONS  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	GLOBAL CEG Series Convector with Thermostat Instruction Manual
Make	GLOBAL
Language	English
Filetype	PDF (Download)
File size	0.27 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• GLOBAL

GLOBAL CEG Series Convector with Thermostat Instruction Manual Overview

Summary of Contents

• Page 1: The heater must be properly installed before it is used. Turn the power on at the circuit breaker panel. Set the thermostat temperature at the wanted room temperature. Remove the front panel and use a vacuum cleaner to remove dust accumulation inside the heater once a year. Use supply wires suitable for 90 °C (194 °F). For bathroom use, the heater must be installed so that switches and other controls cannot be touched by anyone in the bath or shower. Cleaning should be done while the heater is disconnected from the main service panel. Do not operate any heater after it malfunctions. Extreme caution is necessary when any heater is used by or near children or invalids. Do not block air intakes or exhaust in any way whatsoever.