Home > FRICO > FRICO TPT16, TPT16WF Thermostat Instruction Manual

FRICO TPT16, TPT16WF Thermostat Instruction Manual

4

TPT16 / TPT16WF

Release the front cover by pressing with

Installation and operating instructions

screwdriver from the ejector latch at the

bottom of the thermostat. Open the spring and

remove the frame.

Wires must be stripped 9-10 mm. Wires can be

released by pressing the connector’s release

pin. Floor sensor must be placed into protective

tube in concrete. Make sure there is no water in

the tube.

Setup

This manual describes the most essential

functions and technical speciﬁcations of the

thermostat. These instructions help the user to

control the thermostat, and the electrician to

install and setup the thermostat.

Now connect the wires to the thermostat’s

terminals:

PILOT:

LOAD (N):

Pilot Wire (if applicable)

Heating Cable connection (Neutral)

Power connection (Neutral)

Power connection (Live)

Technical speciﬁcations

Heating Cable connection (Live)

Floor temp sensor NTC type

LOAD (L):

SENSOR:

Display: 1.8” TFT, 128x160 resolution

Power supply: 230V - 50/60 Hz

Maximum load: 16A (resistive)

Setpoint temperature range: +5 °C/+40 °C

Usage temperature range: 0 °C/+40 °C

Temperature setback: Pilot wire 230V - 50/60 Hz

IP class: IP21

Standard Color: White RAL9003

Sensors: Built-in room sensor and ﬂoor sensor

NTC 10kΩ included

Wi-Fi: 2.4GHz 802.11bgn (TPT16WF)

Approvals: EN 60730-1, EN 60730-2-9,

EN 300 328 V2.2.2

Installation

Installation must be done by a qualiﬁed

electrician in accordance with wiring and

building regulations.

Before installation, disconnect any power to the

thermostat’s mains. During installation of the

thermostat, power to the thermostat must be

disconnected or isolated AT ALL TIMES!

Next, position the thermostat and fasten it onto

the wall’s mounting box using 2-4 screws. Open

the frame retaining spring, position the frame

and close the spring. Then attach front part,

make sure the connector between front and

bottom part is correctly placed. Press front part

until it snaps in place. Front part can later be

removed by pressing the ejector latch.

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	FRICO TPT16, TPT16WF Thermostat Instruction Manual
Make	FRICO
Language	English
Filetype	PDF (Download)
File size	0.14 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Comments are closed.

FRICO Instructions & User Manuals

FRICO TD10 Electronic Thermostat Instructions

FRICO TAP16R Electronic Thermostat User Guide

Get the free PDF manual for the FRICO TPT16, TPT16WF Thermostat Instruction Manual and access setup steps, usage instructions, and troubleshooting tips. 👉 View online or download now to keep your thermostat running smoothly!

Frico TPT16, TPT16WF Manual: Questions and Answers

Frico TPT16, TPT16WF specifications

Power supply	230V - 50/60 Hz
Maximum load	16A (resistive)
Setpoint range	+5 °C/+40 °C
Sensor	Floor temp sensor NTC type
IP rating	IP21
Wi-Fi	2.4GHz 802.11bgn (TPT16WF)

Full specifications, page 1

What does the wooden floor temperature limit symbol mean on Frico TPT16?

Wooden floor has reached the maximum temperature of 27°C, so heating is being limited. Instruction Manual, p. 2

What do the symbols on the Frico TPT16, TPT16WF main screen represent?

Symbol	Meaning
Time	Current time displayed
Operation mode	Home, Away, Schedule, Anti-frost, or Power regulation
Wi-Fi indicator	Connection status (TPT16WF only)
Heating switched	Heating is currently on
Setpoint	Target temperature setting
Measured temp	Room or floor sensor reading

Instruction Manual, p. 2

What's the difference between Home mode and Away mode?

Home uses a pre-set temperature you can change and save. Away uses a reduced pre-set temperature, also changeable and saved. Instruction Manual, p. 3

Can I set up Frico TPT16, TPT16WF to follow a daily schedule automatically?

Yes. Create customized daily schedules with up to five setpoints per day, each with a target time and temperature. The thermostat will regulate automatically according to the programmed schedule. Instruction Manual, p. 3

Frico TPT16, TPT16WF compared with other floor heating thermostats

Specification	Frico TPT16, TPT16WF	Etherma 3 set 2024	Heat-my-home HMH200	Heatit Z-TRM6 DC Z Wave
Power supply	230V - 50/60 Hz	230 V - 50/60 Hz	85-240 V / 50-60 Hz	230VAC 50Hz
Maximum load	16A (resistive)	16 A (ohmic)	3600 W (16A)	3A 24VDC
Setpoint range	+5 °C/+40 °C	+ 5 °C / + 35 °C	+5° C ... +40° C	5°C to 40°C
Sensor	Floor temp sensor NTC type	10 k Ohm	10 KΩ @25°C, length 3m	NTC type 6.8, 10, 12, 15, 22, 33, 47 or 100kΩ
IP rating	IP21	IP 21	IP21	IP21