Danfoss REPI Series Digital Thermostat User Manual
Data sheet
REPI Series Digital Thermostat Manual
Operations
Sleep: Thermostat will get into sleep function
after programming.The set Temperature should
to be.
On/Off: Press “ ” buttons to turn on;
press “ ” again to turn off.
Setpoint: With thermostat on, press “ ” to
reduce the setpoint, press “ ” to increase the
setpoint, the setpoint step is
To set: Press “ ” button for 3 seconds till
“
” display, there’s a number of count down
in the center of LCD, Use “ ” or “ ” to adjust
the desired sleep time: the max. = 48 hours;
thermostat will return to the working status after
5 seconds, “ ” is flashing to start counting down.
The setpoint should be replaced by the sleep
setpoint.
To quit: When thermostat get into Sleep
function, “ ” will flash, press “ ” or “ ” to quit.
Keypad lock: press “ ” and “ ” for 10
seconds till to “ ” display to activate, under this
function, any keypad is locked.
0.5 °C, the setpoint will be confirmed
automatically after 5 seconds, and then return to
dispay status, press “ ” or “ ” to check setpoint.
Mode: With thermostat on, press “ ” to
change the working mode – Cooling “ ”,
Heating “ ”, Vent “ “, Auto “
( Auto is available REPI-4/ REPI-4N).
”
Fan Speed: With thermostat on, press “ ” to
select the desired speed – low speed “ ”, Med
speed “ ”, High speed “ ”, auto “ ”. If single
speed fan available, there’s only med speed “ ”.
Under auto speed fan, the fan speed will be
changed automatically as below: in low speed
when room temperature
is 1 °C difference with setpoint;in med speed
when room temperature is 2 °C difference with
setpoint; in High speed when
Press “ ” and “ ” for 10 seconds till “
disappear to quit the function.
”
Set Parameters: With thermostat off, press
” for 10 seconds to enter menu to set the
parameters.
“
room temperature is 3 °C difference with
setpoint.
Parameter table
Parameter Description
Default
Range
0 - 2
Step
1
2
Power on status (0: Off; 1: On; 2: Hold)
Fan speed (0: Single Speed; 1: Three Speed)
Fan mode (DA; DB)
2
1
0 - 1
3
0
4
Sensor selection (0: Internal; 1: Remote)
Temperature format (0: Celsius; 1: Fahrenheit)
Temperature calibration
1
0 - 1
0 - 1
5
0
0
0.1
0.1
0.5
0.5
0.5
0.5
0.5
1
6
-20.0 - +20.0
0 - 99.5
0 - 99.5
0 - 10
7
Minimum setpoint
5 °C/41 °F
35 °C/96
2
8
Maximum setpoint
9
Dead band (REPI-4)
10
11
12
Heating & Auto sleep setpoint
Cooling sleep setpoint
7 °C/45 °F
28 °C/82
1
0 - 99.5
0 - 99.5
1 - 32
Comms# (REPI-2N;REPI-4N)
Input Signal Mode 0: Invalid
1: Changeover(REPI-2)
2: thermostat will be sleep without input signal
3: thermostat will be Off without input signal
13
0
0 - 3
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Heating reset time
90 sec.
90 sec.
0
10 - 300 sec.
10 - 300 sec.
0 - 1
10 sec.
10 sec.
Cooling reset time
Ports mode (0: Modulation & Floating; 1: On/Off)
Valve status as turn off (0: Close; 1:Hold; 2: Open )
Port1 Modulation direction (0:10V Open; 1:10V Close)
Port1 Modulation minimum signal
Port1 Modulation proportional
0
0 - 2
0
0 - 1
0Bit
2
0-128Bit(5V/10mA) 0.04V/Bit(0.08mA/Bit)
1 - 20
0 - 1
0.5
Port2 Modulation direction (0:10V Open; 1:10V Close)
Port2 Modulation minimum Signal
Port2 Modulation proportional
0
0 Bit
2
0-128Bit(5V/10mA) 0.04V/Bit(0.08mA/Bit)
1 - 20
0.5
Port1 Floating minimum time
1 sec.
30 sec.
1 sec.
30 sec.
1 - 9 sec.
1 sec.
10 sec.
1 sec.
10 sec.
Port1 Floating maximum time
10 - 300 sec.
1-9 sec.
Port1 Floating minimum time
Port1 Floating maximum time
10 - 300 sec.
Disable / Enable bypass PID control
(0: Disable; 1: Enable)
28
29
0
0-1
Override output value when bypass PID control
Display output value when enable PID control
0 - 255
2 | AI097986404620en-010102
© Danfoss | 2022.05
| General | Details |
|---|---|
| Name | Danfoss REPI Series Digital Thermostat User Manual |
| Make | Danfoss |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.24 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Danfoss RET-MD Electronic Intelligent Dial Setting Thermostat Installation Guide
Danfoss VICUQ24M Icon Programmable II Room Thermostat Installation Guide
Danfoss MBC 8000, MBC 8100 Heavy Duty Thermostat Installation Guide
Danfoss UT 72-UT 73 Universal Thermostat Installation Guide
Danfoss ECtemp 530 Electronic Thermostat Installation Guide
Danfoss 014G0251 Eco Radiator Thermostat User Guide
Danfoss 014G0013 Z Wave Radiator Thermostat Installation Guide
Danfoss RET230P Electronic Thermostat Instruction Manual
Danfoss TP7000 Range Electronic 7 Day Programmable Room Thermostat Installation Guide
Danfoss RET1000 Series Electronic Thermostat User Guide
Infracomfort HY312W Wifi Digital Thermostat User Manual
Thalos Key 230 Bianco Touch Screen Wall Thermostat Instruction Manual
ADVENT AIR ACTH12 Digital LCD Thermostat Instruction Manual
OJ ELECTRONICS MCD5 Touch Thermostat Instructions
Sygonix 2735095 Wireless Indoor Thermostat Instruction Manual
Danfoss MBC 8000 Heavy Duty Thermostat Installation Guide
EMOS P56201BUF Floor Heating Thermostat User Guide
tado 104388 Smart Thermostat Installation Guide
Honeywell Home T6 Pro Smart Programmable Thermostat User Guide
MYSAir Roma Monochrome Backlit Touch Thermostat User Manual