Carrier 33WIFISTAT43 Wi-Fi Thermostat Installation Guide
Table 2 — Parameters (cont)
PARAMETER NAME/DESCRIPTION
DEFAULT AND RANGE
OCCUPANCY OUTPUT — When set to ON-Y3, ON-O/B, or ON-W2, selected relay output equals current Occupancy D: Off
state. Can be used for ECON Enable.
NOTE: The OCCUPANCY OUTPUT option is not displayed or available if Y3, O, and W2 relays are being used; i.e.
Humidification/ Heat Pump/ 3-stage cooling/ etc.
R: Off
On-Y3
On-W2
On-O/B
OCCUPANCY INPUT — This setting changes the current heating and cooling setpoints to the option selected for MAX D: Occupied
HOLD TIME. This occurs when the short is detected on the Remote Space Sensor for the duration of 2 to 5 seconds. R: Occupied
Unoccupied
HUM OUTPUT — Select which output to use for humidifier.
NOTE: Only unassigned outputs are available.
D: Off
R: On-Y3
On-W2
On-O/B
DEHUM OUTPUT — Select the unassigned output to use for dehumidifier (Humid-MiZer™/Perfect Humidity™/Hot Gas D: Off
Reheat).
R: On-Y3
NOTE: Only unassigned outputs are available.
On-W2
On-O/B
LINE FREQUENCY — Used to increment operational timers within the thermostat to ensure timing accuracy.
D: 60HZ
R: 50HZ
60HZ
DEALER NAME — (Optional) This setting identifies the name of the installing contractor and could be carried forward D:
from the sensor if input through the local display. R:
DEALER PHONE — (Optional) This setting identifies the phone number of the installing contractor and can be carried D:
forward from the sensor if input through the local display.
R:
MSTP MAX MASTERS — Used to identify max number of masters for token passing on the MS/TP network.
D: 127
R: 1 to 127
MSTP BAUD RATE — The protocol's baud rate (communication speed) on the MS/TP network. The baud rate must be D: 76,800
the same for all controllers on the network.
R: 9,600
19,200
38,400
76,800
115,000
MSTP MAC ADDRESS — Unique identifier for this thermostat on the MSTP network
D:
1
R: 1 to 127
BACNET UTC OFFSET — Offset applied to UTC time
D: 5 hrs / 0 min
R: -13 to 13 hrs / 0 min
DEVICE ID — This is a unique identifier for this thermostat. The default is the BACnet identifier (16) and the last 4 digits D: 16xxxx
of the thermostat serial number.
R: 1 to 4194302
DEVICE OBJECT NAME — Assign a unique alpha-numeric string. The default is the BACnet identifier (16) and the
last 4 digits of the thermostat serial number. This parameter is limited to a maximum of 16 characters.
D: 16xxxx
R:
DEVICE LOCATION — (Optional) Use to provide details about thermostat location.
D: (Location)
R:
DEVICE DESCRIPTION — (Optional) Use to provide additional details about this thermostat.
D: (Description)
R:
BACNET BMS OCC — Use to enable or disable BACnet occupancy control.
D: No
R: No
Yes
NOTE: Occupancy is determined by 1 of 3 methods. You cannot have BACNET BMS OCC with both
PROGRAMMABLE MODE and REMOTE SENSOR set to OCCUPANCY. Setting BACNET BMS OCC to YES forces
PROG OR NON-PROG to NON-PROG and switches REMOTE SENSOR to NONE if set to OCCUPANCY.
BACNET CONFIG WRITE — If YES, allows BACnet to write to GATED_WRITE points. See Appendix BACnet Points D: No
List.
R: No
Yes
NET GP OUT TIMEOUT — Used to timeout Network General Purpose Outputs.
D: 2 min
R: 2 min
20 min
NOTES:
•
Sets the maximum time to lapse between writes to the present_value property of the output object before it returns
to INACTIVE.
1 hr
•
Accessible only if Y3, W2, or O/B output is available as a GP OUTPUT.
Unlimited
NET GP Y3 MODE — Controls the Y3 output over the BACnet network.
D: Disabled
R: Disabled
•
•
•
DISABLED sets the Present_Value of the BACnet object to INACTIVE and READ_ONLY and the corresponding
output relay will be in a de-energized state
Energized Active
Energized Inactive
Selecting ENERGIZE ACTIVE allows BACnet writes and energizes the output relay when the Present_Value is
ACTIVE.
Selecting ENERGIZE INACTIVE allows BACnet writes and will energize the output relay when the Present_Value is
INACTIVE.
NET GP W2 MODE — Controls the W2 output over the BACnet network.
D: Disabled
R: Disabled
Energized Active
Energized Inactive
•
•
•
DISABLED sets the Present_Value of the BACnet object to INACTIVE and READ_ONLY and the corresponding
output relay will be in a de-energized state
Selecting ENERGIZE ACTIVE allows BACnet writes and energizes the output relay when the Present_Value is
ACTIVE.
Selecting ENERGIZE INACTIVE allows BACnet writes and will energize the output relay when the Present_Value is
INACTIVE.
NET GP OB MODE — Controls the Y3 output over the BACnet network.
D: Disabled
R: Disabled
Energized Active
Energized Inactive
•
•
•
DISABLED sets the Present_Value of the BACnet object to INACTIVE and READ_ONLY and the corresponding
output relay will be in a de-energized state
Selecting ENERGIZE ACTIVE allows BACnet writes and energizes the output relay when the Present_Value is
ACTIVE.
Selecting ENERGIZE INACTIVE allows BACnet writes and will energize the output relay when the Present_Value is
INACTIVE.
8
| General | Details |
|---|---|
| Name | Carrier 33WIFISTAT43 Wi-Fi Thermostat Installation Guide |
| Make | Carrier |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.39 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Carrier 53DFS250-SL Programmable Digital Thermostat Owner’s Manual
Carrier 33TWSPL-4 Wifi Stat Plus Thermostat Owner’s Manual
Carrier EB-STATE3LTICB-01 lLite Smart Thermostat Instructions
Carrier ecobee3 Lite Smart Thermostat User Manual
Carrier EB-STATE7ICR-01 Ecobee for Smart Thermostat Owner’s Manual
Carrier TSTATCCEWF-01 Smart Thermostat Owner’s Manual
Carrier Wi-Fi Enabled 24V Smart Thermostat Instruction Manual
DEVIreg 316 Electronic Thermostat Installation Guide
GENERAL 261S RF Digital Room Thermostat Instruction Manual
UNDERFLOOR HEATING WORLD UT5 Touch Screen Thermostat Instruction Manual
Honeywell CMR707A1049 Programmable Room Thermostat User Guide
homematic IP C-2 Radiator Thermostat Instruction Manual
resideo TH2110WF4008 Smart Thermostat User Guide
GENERAL LIFE MITRA 220 Digital Room Thermostat User Manual
BEOK TDS72 Digital Screen Thermostat Instruction Manual
GENERAL LIFE SOLARA 300S Smart Room Thermostat User Manual
Daikin One Lite Smart Thermostat Instruction Manual