bandary FC660 Smart Thermostat User Guide
1-Select “Check the R wire”, rotation the first
ring to select the “Rc or Rh” or “Rc and Rh”,
press the touch panel to confirm the
selection. (Tip: The System Configuration
confirmation method for each selection is
the same)
Main interface
Cooling&Heating
&Ventilation
mode adjustment
5-Select “Auxiliary setting”, rotation the first
ring to select the “None” or “First stage
heat for heat pump” or “Humidification”
or “Dehumidifier”.
Profile Mode Selective
9-Select “Temperature difference
setting” by rotation the second ring
from 1℃(2℉) to 5℃(9℉), factory
Profile modes setting (Tip: In parameter setting interface,
enter main interface method is the same→Short press the
panel then enter main interface.)
Rotate the second ring in clockwise
to adjust the profile mode:
Profile mode
adjustment
away→home→away...to recycle.
IOS & Android
1.2 Register account inAPP.
default 1℃.
Rotation the first ring to select 3 modes
(Away mode/Daily mode/Holiday mode)
Daily mode
Mode selective
and press the panel to confirm the
2.1 In parameter set two interface, choose the “Wifi pair” to enter
pair mode, the “Wifi” symbol flash in main interface, the device is
in pairing status.
10-Final confirm “Equipment type”, display the parameters previously
selected by the user, if correct, select “Next” and press the touch
panel to proceed to the next step; Finally, select “Finish” to enter
Main Interface.
Rotate the second ring in anticlockwise to adjust the mode:
cooling→heating→ventilation→cooling...to recycle
2-Select “Equipment Installation Setting”,
selection.
rotation the first ring to select the “Heat
Pump” or “Multi Heat Pump” or “Heat
Only” or “Cool Only” or “Back(Back to the
Previous Level)”.
6-Select “Equipment startup delay”, rotation
Note: In mode switch, each operation will have an prompt on panel,
rotate the first ring to select whether switch, press the panel to
confirm the selection.
the second ring to select the delay time
from 0~15min, factory default 3min.
2.2 Click on “+” symbol to “Add device” on “Smart Life” or “Tuya
Smart”, turn on phone WIFI, and then find “Small Home Appliance”
menu to click on “Thermostat (Wi-Fi)”, then please follow the step
to input wifi account no. and password.
1 “Away mode” setting:
You need to rotate the second ring by a larger amplitude (more than
1/4 turn) to shift the modes
Set the “Heat” & “Cool” temperature,
and “Fan” mode to On/Off.
2.3 Follow up with the guideline to operate the next step, the APP
will automatic search the device, and add in its register here.
Parameter Setting
Enter into Parameter Setting
3-Select “How is your O/B Reversing
7-Select temperature display format
2.4 Connect successfully, then the user can control the smart
thermostat by APP.
Valve energized”, rotation the first ring
to select the “On cool” or “On Heat”.
2 “Daily mode” setting:
In main interface long
“℃” or “℉” by anticlockwise the
1 Main interface
Set “Temp. time set” from Monday to Sunday(Figure 1), each day
can be set 6 periods(Figure 2) according to the user’s requirement
(Figure 3);
2 Profile modes
setting
5 ECO On/Off
set
press the panel for more
than 2-second, then the
user get the parameter
setting interface:
second ring.
3 Parameter
set one
6 Key Lock/
Unlock set
Main interface function operation:
7 Fan On/Off
set
4 Power On/Off
set
Function operation instruction
8 Parameter
set two
Set temperature setting
System configuration:
The thermostat is powered on for the first time, follow the display
4-Select “Second level cool and heat
In main interface, clockwise rotation the first ring,
the setting temperature would be 0.5℃ꢀincrease;
Otherwise, anticlockwise rotation the first ring
will keep temperature 0.5℃ꢀdecrease.
8-Select “Dead band setting” by rotation
：
Rotation the first ring to select the parameter setting, and press the
panel to confirm the selection.
setting”, rotation the first ring to select
the “Yes” or “No”.
the second ring from 0.5℃(1℉) to 5℃
guideline to select and confirm the system configuration;
(9℉), factory default 0.5℃(1℉).
(Tip: The Parameter Setting method is the same)
Figure 1
Figure 2
-18-
Figure 3
-14-
-15-
-13-
-17-
-16-
3 “Holiday mode” setting
7 Modbus:Setting the Modbus-RTU parameters.
3 IO state: Display the thermostat input and output state.
Dimension
Set “Holiday start time”(Figure 4), “Holiday stop time”(Figure 5) &
“Holiday setting temp.”(Figure 6), time setting sequence is month,
day, year, hour, minute, and am/pm. In “Holiday setting” interface,
select heat/cool “On” or “Off ” and temperature setting from 16~30℃,
fan runtime(min/hr) from 0~60 (Tip: We recommend 0 min/hr.)
4 System set: Input password “987” to enter System Configuration.
Fan On/Off Set
Press the panel to select “Fan On” or “Fan Off”.
5 System information:Display the thermostat software & hardware
version.
Key Lock/Unlock Set
Press the panel to select “Lock” or “Unlock”.
6 Password modification: Input old password “987” to reset the
password according to user’s requirement.If the user forgot the
modified password, the user can input the super password "999" to
restore the factory default passward "987".
ECO On/Off Set
Press the panel to select ECO mode “On” or “Off”.
7 Restore factory settings: Input password “987” to restore to factory
default value.
Power On/Off set
Press the touch panel to select “Power On” or “Power Off”.
5
5...50>0.5-5
Parameter set two
Figure 4
Figure 5
Figure 6
1 ECO mode: Set the ECO cool temperature
and ECO heat temperature
Parameter set one
RH%
10...50>1-5
ECO mode
wifi pairing
backlight delay
Rotation the first ring to select the parameter
and press the panel to confirm the selection.
Select “Back” to return to the previous
interface.
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
2 Wifi pairing: Select the reset the wifi pair,
timer
fault list
Service support
Modbus
the thermostat is in pairing status.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
3 Backlight delay: The thermostat backlight
setting from 0~100% brightness
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. lf this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
(Tip: The Parameter Selection & Confirmation
method is the same)
4 Time: Time setting sequence is month, day, year, format, hour,am/pm,
minute.
1 Temp./hum. offset: Set temperature offset from 0~10℃, the
temperature offset would be 0.5℃ increase or decrease; Set
humidity offset from 0~100%, the humidity offset would be 1%
increase or decrease.
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
5 Fault list:Setting the fault parameters.
RH
6 Service supports: If you have any questions, please scan the panel
QR code to contact the technician.
FCC Radiation Exposure Statement
2 Temp. up/down limit: Set the upper setting temperature limit from
16.5~50℃; Set the lower setting temperature limit from 1~30℃.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.
-19-
-21-
-22-
-23-
-24-
-20-
| General | Details |
|---|---|
| Name | bandary FC660 Smart Thermostat User Guide |
| Make | bandary |
| Language | English |
| Filetype | PDF (Download) |
| File size | 2.24 MB |
(1 votes, average: 5.00 out of 5)
Loading...
FC610 Bandary Smart Thermostat Owner’s Manual
Raychem Elexant 450c Thermostat Instruction Manual
TRANE XR102 Non-Programmable Thermostat User Guide
namron 16A 2.0 Zigbee Touch Thermostat Instruction Manual
Meross MTS200HK Smart Thermostat User Manual
Haswill STC-8080A Thermostat User Guide
azbil TY6000Z2000 Neostat Room Thermostat Instruction Manual
Network Thermostat X7-Series Thermostat Installation Guide
uponor D Plus RH T-247 BUS Smatrix Base Thermostat Instruction Manual
Remotec REMEZTRVV01 Z Wave Thermostat User Guide
MERSCHEL iQ MD2 Wired Thermostat User Manual