aube TH146-P-2H1C Programmable Thermostat Installation Guide
TH146-P-2H1C
User’s Guide
Programmable H/C Controller
Indicator LEDs
Indicator LEDs
Day
FAULT: System fault
EH: Emergency heat mode
DE: Dual energy
Time and day setting
Programming
Temperature
adjustment
mode selection
Clock
Fan operating
mode selection
Backlight
Program day selection
Program clear
Indoor temperature
The screen is lit for 12 seconds
when any button is pressed.
However, the screen remains lit
while you are configuring the
controller.
System operating
mode selection
Indoor humidity
Humidity setting
Return
Outdoor temperature
Up/Down buttons
5. General Setting
6. Temperature Setting
Display
5.1 Clock and Day Setting
6.1
n Press Clk. The hour display flashes.
Appears when the
temperature setpoint
is displayed
o Set the hour using
p Press Clk. The minute display flashes.
q Set the minutes using
r Press Clk. The day display flashes.
s Set the day using
t Press to return to the normal display.
.
Indoor temperature
Cooling is On
Heating is On
.
System operating mode
Auxiliary heating is On
.
Temperature adjustment
Fan operating mode (ap-
pears when the fan is in
continuous mode, disap-
pears when it is in automat-
ic mode)
mode (appears when the
system is in automatic
mode, disappears when it
is in manual mode)
5.2 Date Setting
n Press Clk for 3 seconds to display the year.
o Set the year using
p Press Clk to display the month.
q Set the month using
r Press Clk to display the date.
s Set the date using
t Press to return to the normal display.
.
The controller normally displays the measured indoor temperature.
To view the setpoint, press one of the buttons. The setpoint and
.
the symbol will be displayed for the next 5 seconds.
.
6.2 System Operating Mode
Press Mode to place the system in one of the following modes:
Fan Operating Mode
5.3
Press the Fan button to select the fan operating mode.
The system is in heating mode.
HEAT
The system is in cooling mode.
COOL
•
In automatic mode, the fan runs only when heating or cooling is
activated. NOTE: For gas-operated HVAC systems, there might
be a delay before the fan starts or stops when heating is acti-
vated or deactivated.
The system is in automatic changeover mode. (The system
switches between heating mode and cooling mode to main-
tain the desired temperature.)
AUTO
The system is off.
OFF
•
In continuous mode, the fan runs continuously and the
sym-
bol is displayed. NOTE: if Smart Fan is enabled, when the con-
troller is in periods 2 and 4 of automatic mode and in
unoccupied mode, the fan will run only when heating or cooling
is activated. The fan will run continuously the rest of the time
The system is in emergency heat mode. Only auxiliary heat-
ing is used when there is a call for heat. (This mode applies
EHEAT
only when the controller is connected to a heat pump
equipped with auxiliary heating).
TH146-P-2H1C
400-280-014-A
5/23/07
9/11
| General | Details |
|---|---|
| Name | aube TH146-P-2H1C Programmable Thermostat Installation Guide |
| Make | aube |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.46 MB |
(1 votes, average: 5.00 out of 5)
Loading...
aube Electronic Thermostat TH131 Owner’s Manual
aube TH114-AF-GA Non-Programmable Thermostat Owner’s Manual
tuya M3 Series Thermostat User Guide
ENGO CONTROLS SE901WIFI Wireless Internet Wi-Fi Thermostat User Guide
Danfoss RAS-C2 Radiator Thermostat Installation Guide
ENGO CONTROLS EFAN-230W WIFI 230V Fan Coil Thermostat User Guide
Danfoss Eco Electronic Radiator Thermostat Instruction Manual
EMSQ22 Daikin ONE Lite Smart Thermostat User Manual
GENERAL LIFE SENNA 300S RF Wireless Room Thermostat User Manual
GENERAL HT250 Digital Room Thermostat User Manual
SILVERCREST IAN 469312_2310 Digital Radiator Thermostat Instruction Manual
neptronic TMA54-EXT1 Thermostat Instruction Manual