SIEMENS RDG200KN Room Thermostat Instruction Manual
Set TIME
Press button
programming mode TIME.
once and then turn the rotary knob or press and hold button
to select
Press button once and then turn the rotary knob to select time format.
Press button once and then turn the rotary knob to select AM or PM.
Press button once and enter the hour setting.
The hour value flashes and can be changed by turning the rotary knob.
Press button once to confirm the adjusted value and enter the minutes setting.
Repeat the steps as for the hour.
Set DATE
Press button
programming mode DATE.
once and then turn the rotary knob or press and hold button
to select
Press button once to enter date setting.
Turn the rotary knob to select month / weekday / year, then press button once.
For example, enter the year setting. The Year value flashes and can be changed by turning the
rotary knob.
Press button to confirm the adjusted value, or (Esc) to cancel the change.
Repeat steps for month and weekday settings.
Set AWAY (Holiday mode)
Press button
once and then turn the rotary knob or press and hold button
to select
programming mode AWAY. Holiday mode
is displayed.
Press button once to enter scheduler mode
Turn the rotary knob to adjust the holidays, then press button once.
Set the start time (AWAY): Set the month (MON) and then press button Set the day (DATE)
Press button once to confirm the adjusted value; the idle page for Holiday mode is displayed.
.
Button lock
If the button lock function is enabled (parameter P028 = 2), pressing the right
button for 3 seconds locks or unlocks the buttons respectively.
Locked buttons are indicated by the key symbol
.
If “Auto lock” is configured (P028 = 1), the thermostat automatically locks the
buttons 10 seconds after the last adjustment.
Commissioning (by qualified HVAC installer)
To adapt the thermostat to your system and optimize control performance, a number of control
parameters can be adjusted. This can be done during operation, either via the buttons on the
thermostat or via a commissioning tool.
Control parameters
To change control parameters, proceed as follows:
1. Press left and right buttons simultaneously for 3 seconds or until device beeps if buzzer function is
enabled (P030).
2. Service level: Release and within 0.5…4 seconds, press the right button again until “P001” is
displayed.
Expert level: Release and within 0.5…4 seconds, press the left button again until the temperature
disappears. Turn the rotary knob counterclockwise minimum ½ rotation. P050 displays.
3. Select the required parameter by turning the rotary knob.
4. Press button (OK). The current value of the selected parameter flashes and can be changed by
turning the rotary knob.
5. Press button (OK) to confirm the adjusted value, or (Esc) to cancel the change.
To adjust additional parameters, repeat steps 3 through 5, or press (Esc) to quit parameter setting
mode.
Note: If password protection (needs to be done by HVAC installer) is enabled, users must enter the password to open
parameter setting mode. If the password is mistyped 5 times, the thermostat is locked and the password cannot be
entered for 5 minutes. Symbols
and
are displayed.
Parameter list
Adj.
No.
Description
Factory setting
Setting range
2-pipe:
1 = Cooling only
0 = Heating only
1 = Cooling only
P001
2 = H/C changeover auto
3 = H/C changeover manual
4 = Heating and cooling
Control sequence
4-pipe:
4 = Heating and
cooling
1 = Auto *** - Protection / Auto - Comfort –
Protection (when there is local scheduler)
2 = Auto *** - Comfort - Economy - Protection
3 = Auto *** (Comfort) - Protection Hospitality
0 = Auto - Manual
Operation via room operating mode
selector
P002
P003
1
1 = Manual
0
Operation via fan operating selector
2 = Auto - Manual - Protection
3 = Auto – Protection
0 = °C (parameter in °C)
P004
P005
0
Unit
1 = °F (parameter in °F)
ON = Enabled
OFF
Scheduler
OFF = Disabled
P006
P007
0 K
0
-5…5 K
-10…0…10 %
Measured value correction
Humidity value correction
0 = Room temperature
P008
0
Standard display
1 = Setpoint
0 = --- (No display)
1 = °C and °F
2 = Outside temperature
3 = Time of day (12 h)
4 = Time of day (24 h)
5 = Humidity
P009
0
Additional display information
1 = Comfort concept
P010
P011
P013
1
Setpoint concept
2 = Energy saving concept
5…40 °C (41…104 °F)
(P010 = 1): 5 °C (41 °F)...P016-1 K
(P010 = 2): 5 °C (41 °F)...P014-1 K
21 °C (70 °F)
5 °C (41 °F)
Comfort basic setpoint
Comfort setpoint minimum
P014
P015
21 °C (70 °F)
25 °C (77 °F)
P013+1 K…P015-1 K
P014+1 K…P016-1 K
Comfort setpoint maximum heating
Comfort setpoint minimum cooling
(P010 = 1): P013+1 K...40 °C (104 °F)
(P010 = 2): P015+1 K...40 °C (104 °F)
--- (0), 5 °C…P020 (41 °F…P020)
P020 = 40 °C max. (P020 = 104 °F max.)
--- (0), P019…40 °C (P019…104 °F)
P019 = 5 °C min. (P019 = 41 °F min.)
P016
P019
P020
35 °C (95 °F)
15 °C (59 °F)
30 °C (86 °F)
Comfort setpoint maximum
Economy heating setpoint
Economy cooling setpoint
P024
P026
50
---
--- (0), P026 or 20…90 %
--- (0), 20…90 % or P024
Humidity setpoint high
Humidity setpoint low
P027
****
ON = Enabled
OFF = Disabled
0 = Unlocked
ON
Electric heater when cooling
1 = Auto lock
✓ means function locked
2 = Manual lock
3
4
5
6
7
8
9
✓
10
11
12
13
14
15
✓
✓
✓
✓
✓
✓
✓
✓
✓
P028
P029
0
Keypad
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
0 = Fan disable
1 = Low speed (Heat and Cool)
2 = Low speed (Cooling only)
3 = Fan disable Auto & Manual
4 = Low speed Auto & Manual
0
Fan: Dead zone Comfort mode
Buzzer function
5 = Low speed Auto & Manual Cooling
ON = Enabled
OFF = Disabled
P030
***
ON
When no time schedule via KNX exists, Auto equals Comfort.
**** Parameter P027 is displayed only for application 2-pipe with electric heater.
All temperature settings are in increments of 0.5 °C.
Remember to record all changes!
© Siemens Switzerland Ltd, 2020
Issued by
Technical specifications and availability subject to change without notice.
Siemens Switzerland Ltd
Smart Infrastructure
Global Headquarters
Theilerstrasse 1a
CH-6300 Zug
Tel. +41 58 724 2424
A6V11545973_en--_b
A5W00031435A-AB
2021-07-14
Siemens Smart Infrastructure
| General | Details |
|---|---|
| Name | SIEMENS RDG200KN Room Thermostat Instruction Manual |
| Make | SIEMENS |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.24 MB |
(1 votes, average: 5.00 out of 5)
Loading...
SIEMENS RDZ100ZB Zigbee Room Thermostat Owner’s Manual
SIEMENS RDG400 Room Thermostat Instruction Manual
SIEMENS M3182 Room Thermostat Instruction Manual
SIEMENS RDS120-B Smart Thermostat Instructions
SIEMENS Powers Controls TH 192-3 Series Day Night Vent Room Thermostat Instruction Manual
SIEMENS RDY2000BN BACnet Commercial Thermostat User Manual
SIEMENS RDH100RF/SET Room Thermostat Instruction Manual
SIEMENS RDH100RF/SET Wireless Room Thermostat with LCD User Guide
SIEMENS RS485 Flush Mounted Room Thermostat User Manual
SIEMENS RDG260KN Room Thermostat Instruction Manual
GENERAL ARUNA 300S RF Digital Room Thermostat User Manual
GENERAL LIFE FH100S Floor Heating Room Thermostat User Manual
nVent RAYCHEM RayStat-M2 Thermostat Instruction Manual
ENGO CONTROLS E10W230WIFI WiFi Temperature Thermostat User Guide
UNDERFLOOR HEATING WORLD UM1 Thermostat Instruction Manual
Carrier 33TWSPL-4 Wifi Stat Plus Thermostat Owner’s Manual
HIVE HAH2INSTAMZ-01 Active Heating Thermostat User Guide
HIVE Cheap Smart Thermostat User Guide
WATTS Tekmar Wi-Fi Thermostat Instruction Manual
tekmar IOM-T-560 Programmable Thermostat Instruction Manual