Home > Network Thermostat > Network Thermostat NetX X7 Series Thermostat Instruction Manual

Network Thermostat NetX X7 Series Thermostat Instruction Manual

This completes the CO2 settings that can be controlled from  
the Installer Menu. Additional advanced settings can be  
accessed on the embedded web pages and/or the Internet via  
our NetX CloudConnect software. For more information go to  
ACCESS THE FIRST CO2 SETTINGS  
SETTING THE CO2 ALERT SETTING  
After the display of the Faceplate and backplate firmware, the  
By default, the CO2 Alert setting is set to trigger when the X7  
thermostat detects a CO2 reading above the 1100 ppm (parts  
per million) of CO2. When triggered, the alert can activate a relay  
to open a fresh air damper to decrease the level of CO2 in the  
menu will shift to the first setting Conventional/HP Use the  
Right Arrow  
button to navigate through the Installer Menu.  
M
The first menu setting to adjust is CO2 Display  
NetX™ X7 Series  
Thermostat  
control area. To adjust the alert level, use the Up  
and Down  
J
buttons. The level is changed in increments of 50 ppm (parts  
K
per million). The range is from 500 ppm to 2000 ppm. Once the  
desired level is set, press the Right Arrow  
proceed to the Clear CO2 Max Setting.  
button to save and  
CO2 Display: On  
M
CO2 INSTALLATION ADDENDUM  
CO2 INTRODUCTION  
This addendum addresses the installation and configuration  
of the CO2 sensor for the X7C and X7 Series thermostats.  
CO2 Alert @1100ppm  
This includes the display options, alert levels, and resetting  
the maximum level recorded.  
NOTE: This addendum only applies to X7C Thermostats  
A
or X7 thermostats with the optional NT-MOD-CO2 module  
installed.  
ACCESS THE INSTALLER MENU  
SETTING THE CO2 DISPLAY  
Press and hold the Menu Button  
on the bottom left side of  
D
The default CO Display setting is On. This means the CO2  
setting will be v2isible on the upper left corner of the display  
when the thermostat is in normal mode. The CO2 display can  
also be turned off or set to display only when a high CO alert  
the faceplate. Once in the Installer section, you will see the  
Faceplate and Backplate firmware versions in the dot matrix  
display.  
is active. Use the Up  
selection.  
and Down  
buttons to change2the  
J
K
CLEAR CO2 MAX SETTING  
By default, the Clear CO2 Max setting is set to No which means  
the maximum recorded CO level will not reset until user  
intervention. This setting ca2n be changed from No (does not  
reset) to 12 midnight (resets automatically at 12 midnight), or Yes  
(resets now). To adjust the Clear CO2 Max setting, use the  
To accept the settings, press the Right Arrow button. This will  
M
CO2: 944ppm  
accept the setting and move you to the next setting CO2 Alert.  
Up  
and Down  
buttons. To accept the new setting, press  
J
K
button.  
the Right Arrow  
M
CO2 Display: On  
Clear CO2 Max: No  
Page 2  
GeneralDetails
NameNetwork Thermostat NetX X7 Series Thermostat Instruction Manual
MakeNetwork Thermostat
LanguageEnglish
FiletypePDF (Download)
File size0.14 MB
Download PDF
1 Star2 Stars3 Stars4 Stars5 Stars (1 votes, average: 5.00 out of 5)
Loading...
Network Thermostat X7-Series Thermostat Installation Guide
Network Thermostat X7-Series Thermostat Installation Guide
Network Thermostat X7C-WIFI Smart Touchscreen Thermostat Instruction Manual
Network Thermostat X7C-WIFI Smart Touchscreen Thermostat Instruction Manual
Network Thermostat X5-WIFI Smart Touchscreen Thermostat Instruction Manual
Network Thermostat X5-WIFI Smart Touchscreen Thermostat Instruction Manual
Network Thermostat NetXTM X-Series Thermostat Installation Guide
Network Thermostat NetXTM X-Series Thermostat Installation Guide
network thermostat NetX X5-CFA Universal Setback Thermostat Instruction Manual
network thermostat NetX X5-CFA Universal Setback Thermostat Instruction Manual
network thermostat NetX X Series Thermostat Instruction Manual
network thermostat NetX X Series Thermostat Instruction Manual
network thermostat NetX X-Series Ethernet Thermostat Owner’s Manual
network thermostat NetX X-Series Ethernet Thermostat Owner’s Manual
network thermostat X-Series Ethernet Thermostat Instruction Manual
network thermostat X-Series Ethernet Thermostat Instruction Manual
network thermostat X X7-WIFI Smart Touchscreen Thermostat Instructions
network thermostat X X7-WIFI Smart Touchscreen Thermostat Instructions

Network Thermostat NetX X7 Series Thermostat Instruction Manual