Honeywell RCHT8610WF T5 Plus Smart Thermostat Installation Guide
7
Record if you have wires in the
following terminals
Terminal
Wire Color
Installing your T5 Smart Thermostat
Do not include jumpers as a part
of your count. The thermostat
does not need jumpers.
R
RH
Rc
8
Write down the color of the wires
Check mark the wires that are connected to terminals. Next to the
check mark, write down the color of the wire. Do not include jumpers
as a part of your count.
Check all that apply (Not all will apply):
Terminal
Wire Color
Terminal
Wire Color
A or L/A
Y
UWP
Mounting Anchors
System
T5 Smart
Thermostat
O/B
Y2
G
Screws
Wall
W2 or AUX
E
C
Required (see step 9)
11 Bundle and insert wires through
the UWP
W
K
Pull open the UWP and insert the
bundle of wires through the back
of the UWP.
Make sure at least 1/4-inch of
each wire is exposed for easy
insertion into the wire terminals.
S and U terminals are not supported with this thermostat.
If there are wires in terminals that are not listed, you will need
additional wiring support. Visit honeywellhome.com/support to
find out if the thermostat will work for you.
12 Insert the wall anchors
It is recommended that you use
the wall anchors included in the
box to mount your thermostat.
9
Do you see a wire connected to the C terminal?
If yes, skip to step 10.
If you do not see a C wire, proceed with the options below:
You can use the UWP to mark
where you want to place the wall
anchors.
Option A - Finding the C-Wire:
There might be an extra wire pushed into
the wall or wrapped around the wire bun-
dle. Gently pull the wire bundle out of the
wall to check for unused wires.
a) Level the wall plate.
b) Mark the location of the wall
anchors using a pencil.
If you have an unused wire, connect that
wire to the C terminal on your new ther-
mostat in step 13.
c) Drill the holes.
d) Insert wall anchors.
Connect the other end of the unused wire
to the C terminal on your heating/cooling
system (or the zone panel if your home
uses more than one thermostat to control temperature). Be sure any
other wire(s) connected to the C terminal stay securely connected
when you re-tighten the terminal.
e) Make sure anchors are flush
with wall.
Tip: Use a 7/32 drill bit.
Not all heating/cooling equipment use the C label for the 24 VAC
common wire. If your heating/cooling equipment does not have a C
terminal, check the system manual or contact the manufacturer to
find out which terminal is the 24 VAC common.
Complete installation by following the remaining steps in this guide.
Option B - Using the C-Wire Power Adapter:
If you do not have an unused wire in the wall, and Y and G wires are
used, the THP9045A C-Wire Power Adapter can be used.
10 Disconnect the wires and remove the
old wall plate
Use a screwdriver to release wires from
terminals.
Tip: To prevent wires from falling back
into the wall, wrap the wires around a
pencil.
3
| General | Details |
|---|---|
| Name | Honeywell RCHT8610WF T5 Plus Smart Thermostat Installation Guide |
| Make | Honeywell |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.66 MB |

Honeywell T6 Pro Programmable Thermostat User Manual

Honeywell D1-528 Direct Thermostat Installation Guide

Honeywell FocusPRO P200 Programmable Thermostat User Guide

Honeywell RCHT8610WF Series Smart Thermostat Installation Guide

Honeywell T9 Smart Thermostat Installation Guide

Honeywell TH2320WF4011 FocusPRO Smart S200 Series Thermostat User Guide

Honeywell TL116A Thermostat Installation Guide

T10 Pro Smart Thermostat with Redlink Room Sensor

Honeywell TH6320WF2003 Lyric T6 Pro Wi-Fi Programmable Thermostat User Guide

Honeywell RTH9580 Wi-Fi Color Touchscreen Programmable Thermostat User Guide

























