GENERAL HT300S Smart Room Thermostat User Manual
13-When the product is not used for a long period (more than 15 days), remove the batteries.
Otherwise, malfunctions thatwill occur areout of warranty.
The heating unit remains switched off for 10 minutes unless manual intervention is
performed on the room thermostat. A warning appears on the mobile application
that an open window has been detected. The heating unit is activated at the end of
10 minutes. If the room thermostat detects that the window is closed, the heating
unit continues to work. If the temperature continues to drop, the heating unit is
turned off again.
In orderto change the manual mode temperature, pressthe “Up” or “Down”button
while in the main screen. The Room Thermostat will switch to Manual Mode once
pressedthe“Up” or “Down”button.
Your Room Thermostat sends the last status signal to the Receiverevery3 minutes.
Thus, yourRoom Thermostat and Receiverwork synchronously. If the signal cannot
reach to the Receiver from the Room Thermostat for 22 minutes, it perceives that
the connection is broken and stops the heating/cooling operation for safety
reasons. Likewise, in cases where the electricity comes back after a power failure,
the Receiver does not operate the heating/cooling unit until 'operate' signal reaches
from the Room Thermostat. However, in this case, if the Room Thermostat
continues to operate normally, it will continue to work properly without any need for
intervention since itsends astatussignal to theReceiverevery3 minutes.
14-Damages that may occur during the transportation of devices and apparatus are not
coveredbythewarranty. Customers can takeatransportation insurance.
15-Damages caused by mains voltage / faulty electrical installation are not covered by the
warranty.
You maypressthe“Mode”button to switchto theother modes.
PROGRAMMING MODE
You may set the operating schedule of your Room Thermostat with weekly program
16-Devices and apparatuses are out of warranty for malfunctions caused by force majeure
such asfire, flood, earthquakeetc.
If the room Thermostat is operated in cooling mode, a sudden temperature rise is
taken into account.
mode.
programming. These valuescan be setin temperatureadjustmentscreens'' P0-P6''.
7
different temperature values can be set for each day in weekly
17-All of the devices and apparatuses, including all their parts, are under the warranty of our
company.
This featurecan be enabled/disabled fromtheroomthermostatsettings:
In order to set the weekly schedule, press and hold the “Weekly Program“ button
for 3 seconds while your Room Thermostat is on. The “Hour, Minute and Day”
setting will appear. Press the “Settings” button until the “Weekly Program” menu
(P0)appears.
18-In case of malfunction of the devices and apparatuses within the warranty period, the
time spent during repairment period is added to the warranty period. The repair period of the
productcannot exceed20 working days. This period starts fromthe date of notification to the
service station of the malfunction related to the product or, in the absence of a service
station, to the seller, dealer, agency, representative, importer or manufacturer of the product.
Consumer can report the problem by; phone, fax, e-mail, registered and reply paid letter or a
similar way. However, in case of a conflict, responsibility of proveis belong to the customer. If
the malfunction of the product is not repaired within 20 working days, the manufacturer-
producer or importer; has to allocate another product with similar features to the use of the
consumer until therepairof theproductis completed,
Pressthe“ON/OFF”button for 3 seconds while yourdeviceis turned off.
Pressthe“ON/OFF”button until the“ ” menu appears.
Press the “Up” or “Down” button while in the “ ” menu to choose the “
” option and pressthe“ON/OFF”button.
FREQUENTLY ASKED QUESTIONS
Ismy Room Thermostatcompatible withmy heating/cooling unit?
” or
If your heating/cooling unit has On-Off connections, your Room Thermostat is
compatible. You can find information about your heating/cooling unit from your
heating/cooling unit operating manual or fromyourheating/cooling unit service.
“
Days of the week will be blinking on the screen. You can initiate the weekly
programsettingif youwish to setthesameschedule for everydayof theweek.
Pressthe “Up“ button once if youwish to set the same schedule for the weekdays.
Firstfivedaysof weekwillbe blinking on thescreen.
To savethesettingsand exit, pressthe“ON/OFF”button until thedeviceturns off.
The settings you have made are saved. Your device will work with the setting you
How willIconnect myheating/cooling unit withmyReceiver?
Heating/Cooling Unit
On
havemade when youopen it.
We recommend that the connection between the Receiver and heating/cooling unit
should be made byprofessionally qualified persons.
Off
On
Room
Temperature
Press the “Up“ button once more if you wish to set the same schedule only for the
weekend. Lasttwodaysof theweekwillbe blinking on thescreen.
Press the “Up“ button one more time if you wish to set the same schedule for
every day of the week. 1st day of the week will be blinking on the screen. You can
switch between the days by pressing the “Up“ button. Press the “Down“ button in
orderto switchto thepreviousday.
19-Although theconsumer uses his/her repairrights,
2x0.75mm cableis sufficientfor theReceiver– heating/cooling unit connection.
Connect one end of the cable pair to the room thermostat connection terminals
statedin theuser manual of yourheating/cooling unit.
22oC
-If the product breaks down for 4 times in a year or 6 times in warranty duration and these
problemseffectsmain purpose of theproduct.
(starting fromdelivery timeduring warranty.)
Connect the other end of the cable pair to COM and NO inputs of the terminal inside
theReceiverasshown in the"RECEIVERWIRINGDIAGRAM" section.
The directionof thecableends does not matter.
- Exceedingthemaximum timerequiredfor repair,
17oC
- In the event that the service station is not available, if it is determined that the repair of the
defect is not possible with the report prepared (in order) by one of the seller, dealer, agency,
representative,importer or manufacturer, a refundor a price discount at the rate of defect can
be requested.
Pressthe“WeeklyProgram“button once to setaschedule.
Time
“P0” will be blinking on the screen. Set the temperature value of “P0” by pressing
the “Weekly Program“ button once more. The hour setting of “P0” cannot be
changed since it's factory setting.
15 min.
25 min.
40 min.
DECLARATION OF CONFORMITY
ISIPARK İÇ VE DIŞ TİC. İNŞ. ISITMA SİSTEMLERİ OTO. SAN.A.Ş.which Head Office and
FACTORY SETTING RESET
20-The customer can make complaints and appeals to consumer courts or consumer
arbitrationcommittees.
You can reset your Room Thermostat to its default factory settings. This operation
resets the mode temperature values, calibration setting, heating/cooling modes,
and hysteresis settings to the factory setting. To reset your room thermostat to
factory setting:
production site is located on Fatih Mah. 1188 Sk.No:13/A Sarnıç
-
Gaziemir
-
İZMİR
–
Press the “Weekly Program”button again. Day indicator will be blinking. If you will
not change the day, press the “Weekly Program” button again and switch to the
“P1” settingbypressingthe“Up” button.
TÜRKİYE confirms and declaresthat the productmarkedwith CE and its specifications below
is coveredbytheprovisionsof thementioned directive.
21-The warranty document must be kept by the customer during the warranty period. If the
document is lost,
replacementof devicesand apparatus will be made for afee.
a
second document will not be issued. In case of loss, repair and
Brand
: GENERAL Life
: HT300S SMART
: Smart Room Thermostat
First, hour setting will appear on the screen. Once you complete the hour setting,
adjust the minute setting by pressing the “Weekly Program” button. After the
minute setting, pressthe“WeeklyProgram”button to setthetemperaturevalue.
Follow thesamestepsfor other schedule settings.
ProductName
ProductType
While yourdeviceis turned off, pressthe“ON/OFF” button for 3 seconds.
Pressthe“ON/OFF”button until the“
While in the “ ” menu, select the “
and pressthe“ON/OFF”button.
Your devicewillbe turned off and resetto factory settings.
” menu appears.
WARRANTY CERTIFICATE
The product manufactured by ISIPARK and mentioned above is connected wirelessly at 2.4
Ghz internet and periodically shares the temperature and status information with the server
on theinternet.
” option by using the “+” or “-” buttons
Manufacturer
Once all changes made, press and hold the “Weekly Program” button for
seconds to save.
3
Title: ISIPARK İÇ DIŞ TİC. A.Ş.
Adsress: Fatih Mah. 1188 Sk. No:13/A Sarnıç
Gaziemir İzmir-TÜRKİYE
Tel: +90 (232) 457 99 50
Fax: +90 (232) 457 91 22
E-Mail: generallife@generallife.com.tr
Authorised Signatory:
Compatible Directives:
Radio and Telecommunications TerminalEquipmentRegulation
2014/53/EU(ETSI EN301489-1 V2.2.3(2019-11),
Note: In order to check the weekly schedule which has been set without making any
changes, press the “Weekly Program” button once while your Room Thermostat is
on. Press the “Up” and “Down” buttons to see the days, press the “Mode” button to
seethesettingsbetween“P0-P6”.
KEY LOCK
In the Room Thermostat there is a key lock function to avoidany unintended
contact.
ETSI EN301489-17 V3.2.4(2020-09), EN300220-1V3.1.1,
EN300220-2V3.2.1(2018-06), EN62479:2010, EN62368-1:2014+A11:2017)
ElectromagneticCompatibility Regulation 2014/30/EU
In order to unlock the Room Thermostat's key lock the “On/Off” button
should be pressed for 3 seconds. If buttons on Room Thermostat are not
touched for 10seconds, keylockwill be reactivated.
(ETSI EN301489-1 V2.2.3, ETSI EN301489-3 V2.1.1)
ROOM THERMOSTAT WORKING LOGIC
HeatingMode
Low Voltage Directive2014/35/EU(EN60730-2-9)
Company Stamp:
Supplementary Information: Mentioned product can be used with combi boilers with on / off
output and compatibility with the directive only covers the product. ISIPARK is not
responsible for the compliance of the entire system with the directive. This declaration does
not apply when changes aremade to theproductwithout obtaining our consent.
Your room thermostat takes the average room temperature of the last 40 seconds
as the basis. If the room temperature goes above the hysteresis positive
temperaturevalue you set, your room thermostat will stop the heating unit. If it goes
below the hysteresis negative temperature value, your room thermostat will start
the heating unit. Thus, it ensures that the room temperature remains within a
certain range.
DAY AND HOUR SETTINGS
While your Room Thermostat is on, keep pressing the “Weekly Program” button
for 3 seconds.
Product
Type: Smart Room Thermostat
Brand: GENERAL Life
At the first screen that appears, hour part will be blinking. You may set the time
withthe“Up” and“Down” buttons.
Model: HT300S SMART
Guarantee Period: 2 Years
Max. Time to Repair: 20 Days
Banderole and Serial Number:
After setting the time, the “Settings” button needs to be pressed once. For minute
setting, minute part will be blinking. You may set the minute with the “Up” and
“Down” buttons.
Room
Temperature
22.5oC
Set
Temperature
22.0oC
After setting the minute, the “Settings” button needs to be pressedonce to set the
dayof theweek.
21.5oC
WARRANTY CONDITIONS
1-The warranty period starts from the invoice date and warranted against manufacturing
defectsfor 2 years.
Mondayhas setasthefirstdayof theweekand indicated withnumber “1".
Numbers indicate the following days respectively 2-Tuesday, 3-Wednesday, 4-
Thursday, 5-Friday, 6-Saturdayand 7-Sunday
Heating
Unit On
Vendor
Title:
2-Devices and apparatus are delivered to the customer in working condition in our company.
On-sitecommissioning is subjecttoaservice fee.
When setting is done, you may exit by pressing the “Weekly Program” button for 3
seconds.
3-The repair of the devices and apparatus covered by the warranty is carried out in our
company factory and should send by contracted transportation company. In on-site
services, the transportation and accommodation expenses of the service personnel belong
to the customer. The shift fee during transportation is added to the service fee and collected
in advance.
Heating
Unit Off
Address:
Time
MODE SETTING
PRESET MODES
MODES
Tel:
Fax:
CoolingMode
Your Room Thermostat takes the average room temperature of last 40 seconds as
basis. If the room temperature goes above the hysteresis positive temperature
value you set, your Room Thermostat will start the cooling unit. If it goes below the
hysteresis negative temperature value, your Room Thermostat will stop the cooling
unit. Thus, itensuresthattheroomtemperatureremainswithin acertain range.
E-Mail:
4-The maintenance of devicesand apparatus is done in our company. Forthe maintenance of
thedevicesand apparatus, theroundtravelfaresbelongs tothecustomer.
5-In case of malfunctioning of the devices and apparatus whose warranty period continues,
it is tested in our company whether the malfunction is caused by a customer or manufacturer
fault, and itis reportedwithareportissued byour company.
Invoice Date and Number:
Delivery Time and Place:
Authorised Signatory:
Company Stamp:
WEEKLY
PROGRAM
MODE
MANUAL MODE
Comfort
Mode
Economy
Mode
Holiday
Mode
6-In case of detection of manufacturer-induced errors of devices and apparatus whose
warranty period continues, the customer can request a replacement or repair of the devices
and apparatus atfull expense bythemanufacturer, unless it's higher than theproduct's price
7-In the event that the faults of the devices and apparatus whose warranty period continues
aredeterminedascaused bythecustomer, allexpenses would be belong to thecustomer.
8-Customers should be aware of damages (if there is any) of product and warn manufacturer
since the day warranty duration starts.If customer do not warn manufacturer with
knowledge of damage, customerlose therights of article 6.
Room
Temperature
Your Room Thermostat has 5 different modes. 3 of them (Comfort, Economy and
Holiday Mode) are preset modes. Other modes are manual mode and weekly
programmode.
22.5oC
Product
22.0oC
Set
Temperature
21.5oC
Type: Smart Room Thermostat
Brand: GENERAL Life
Model: HT300S SMART
In preset modes, temperature values are based on user's choices which have been
set in the beginning. Manual mode allows the Room Thermostat to operate within
the temperature which is required and set directly by user. Weekly Program mode
continues to workaccordingto theweeklyschedule determined bytheuser.
In orderto change thetemperaturevaluesof presetmodes:
STAMP
Cooling
Unit On
9-Malfunctions resulting from the use of devices and apparatus contrary to the matters
statedin theUserManualarenot coveredbythewarranty.
10-Devices and their apparatus are out of warranty if they are beaten, broken or scratched by
thecustomer.
Press and hold the “Mode” button for 3 seconds while your Room Thermostat is
on.
Cooling
Unit Off
Time
11-Damages resulting from the use of devices and apparatus belonging to other brands and
models without theapprovalof themanufacturerarenot coveredbythewarranty.
12-Battery leakage and errors due to rust, oxidation and liquid contact by working in acidic /
humid environmentsarenot coveredbythewarranty.
Comfort Mode temperature value will appear. You may adjust the temperature
valueof Comfort Mode bypressingthe“Up” and “Down”buttons.
When setting is done, you may adjust the temperature value of Economy Mode
withthe“Up” and “Down”buttons bypressingthe“Mode”button again.
You mayexitthesettingscreenbypressingthe“Mode”button 3 seconds.
Isıparkreservestherights of changing productspecificationsand user manuals.
*For allchanges,youmayvisitgenerallife.com.tr
5
6
7
8
| General | Details |
|---|---|
| Name | GENERAL HT300S Smart Room Thermostat User Manual |
| Make | GENERAL |
| Language | English |
| Filetype | PDF (Download) |
| File size | 2.14 MB |
(1 votes, average: 5.00 out of 5)
Loading...
GENERAL ARUNA 300S Smart Room Thermostat User Manual
GENERAL HT250S Digital Room Thermostat User Manual
GENERAL FH260S Underfloor Heating Thermostat User Manual
GENERAL HT100S Digital Room Thermostat User Manual
GENERAL SOLARA 330S SMART Smart Room Thermostat User Manual
GENERAL HT250 Digital Room Thermostat User Manual
GENERAL SENNA 300 Digital Room Thermostat User Manual
GENERAL ARUNA 300S RF Digital Room Thermostat User Manual
GENERAL SENNA 300 Smart Room Thermostat User Manual
GENERAL MITRA 250S Digital Room Thermostat User Manual
Honeywell FocusPRO 5000 Series Digital Thermostat User Guide
ENGO CONTROLS EONE-BATW, EONE-BATB Internet Controlled Thermostat User Guide
Honeywell Home FocusPRO S200 Smart Thermostat User Manual
CENTER EHE0200123 Wired 7 Day Programmable Thermostat Installation Guide
EPH CONTROLS RDTP Recessed Programmable Thermostat Installation Guide
LUXPRO PSD111+ Series Thermostat Instruction Manual
SALUS CONTROLS SQ610 Quantum Smart Thermostat User Guide
TechPunt E1 Smart WiFi Radiator Thermostat User Guide
ESP ECSPST Fort Programmable Thermostat User Manual
Danfoss RET2001OT Digital Open Therm Room Thermostat User Guide