Home > GE current > GE current WTS10 Daintree Wireless Thermostat Installation Guide

GE current WTS10 Daintree Wireless Thermostat Installation Guide

1

2

3

4

Daintree Networked Wireless Thermostat (WTS10)

Installation Guide

Joining the Zigbee Network

Speciﬁcations

After successfully completing the Installation Test the WTS10

is ready to communicate with the Daintree Wireless Area

Controller (WAC) and be commissioned and conﬁgured using

the ControlScope Manager (CSM) web-based application. The

thermostat automatically tries to join the WAC network every

5 minutes. The WAC must be commissioned and Add New

Devices must be initiated on the WAC before the thermostat

can join the ZigBee wireless network.

Power Supply

Output

24VAC, 50Hz

3A max, 1A each terminal

Operating

Environment

32°F to 113°F (0°C – 45°C). Indoor use only

Compliance

ETL listed, FCC ID: D12CT-EM2606, IC ID:

1700A-CT-EM2606

For information about conﬁguring the thermostat using

CSM, see the on-line help.

Radio

Properties

2405 ~ 2475MHz

Transmit Power max 10dbm

Once the thermostat is joined, it ignores its built in schedules.

The WAC passes conﬁguration information like set point, heat/

cooling mode, lock levels etc. at the start of each CSM schedule.

If the thermostat loses communication with the WAC the

following things will happen: (1) Thermostat continues to use

the existing conﬁguration set by the WAC. (2) Keypad automatically

unlocks after 30 minutes to allow manual changes. (3) If remote

temperature sensor(s) are enabled, and the thermostat does not

receive a remote temperature report within 15 minutes, it will

switch to its built-in temperature sensor.

Fahrenheit or Celsius

Display range: 14°F – 99°F (5°C – 37°C)

Display resolution: 1°F (1°C)

Setting range: 45°F – 90°F (7.0°C – 32.0°C)

Setting resolution: 1°F (0.5°C)

Accuracy: +/- 1°F @ 75°F

Temperature

Measurements

Switching differential 1st stage:

User selectable

• 0.5°F (default), 1.0°F, 2.0°F

(0.25°C, 0.5°C, 1.0°C)

Current Certiﬁcation

Switching differential 2nd stage:

Fixed 2°F (1°C)

32°F to +113°F (0°C – 45°C)

Operating Environment

Indoor Use Only

Switching differential 3rd stage:

Fixed 2°F (1°C)

2405 ~ 2475MHz

Radio Properties

Control

Transmit Power max 10dbm

Operational differential: Less than +/- 2°F

Control timing:

Radio Equipment Directive

2014/53/EU

Compliance

• Compressor short cycle timer – 5 min

Residual cooling fan delay:

User selectable

Power Supply

24VAC, 50Hz

• 0 (disabled), 30, 60, 90 sec

• Default = 60 sec

Current declares that the radio equipment type (WTS10)

complies with Directive 2014/53/EU

Control Switches:

• Latching relay, 2A max load per relay

Relays:

Full declaration text available at: www.LED.com

Max. radiated power: <10 dBm. Frequency: 2405 - 2475 MHz

• 1st stage/Aux heating control

• 2nd stage/Emergency heating control

• Fan Control

• Heating/Cooling O/B control, 3rd stage

conventional heat control

• 1st stage cooling control / 1st stage

heat-pump heating control

• 2nd stage cooling control / 2nd stage

heat-pump heating control

WTS10

Switching

Circuit

CAUTION

RISK OF EXPOSURE IF BATTERY IS REPLACED BY AN

INCORRECT TYPE. DISPOSAL OF USED BATTERIES

ACCORDING TO THE INSTRUCTIONS.

These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation, operation

or maintenance. Should further information be desired or should particular problems arise which are not covered sufﬁciently for the purchaser’s purposes, the matter should be

referred to GE Current, a Daintree company.

www.gecurrent.com

General Electric Company and are used under license. Information provided is subject to change without notice.

All values are design or typical values when measured under laboratory conditions.

DT103 (Rev. 05/25/2021