COPELAND 1F86-0244 Blue 2 Inch Single Stage Thermostat Instruction Manual
INSTALLATION
Battery
Door
REMOVE OLD THERMOSTAT
1. Shut off electricity at the main fuse box until installation is
complete. Ensure that electrical power is disconnected.
2. Remove the front cover of the old thermostat. With wires
still attached, remove wall plate from the wall. If the
old thermostat has a wall mounting plate, remove the
thermostat and the wall mounting plate as an assembly.
Mounting
Hole
Mounting
Hole
3. Identify each wire attached to the old thermostat using
the labels enclosed with the new thermostat.
4. Disconnect the wires from old thermostat one at a time. DO
NOT LET WIRES FALL BACK INTO THE WALL.
O/B
Switch
5. Install new thermostat using the following procedures.
Opening
for wires
Gas/Elec
Switch
ATTENTION: MERCURY NOTICE
Figure 1.Thermostat Base
This product does not contain mercury. However, this
product may replace a product that contains mercury.
GAS / ELEC SWITCH
Mercury and products containing mercury must not be
discarded in household trash. Do not touch any spilled
mercury. Wearing non-absorbent gloves, clean up any
spilled mercury and place in a sealed container.
If your system is a heat pump, the GAS/ELEC Switch must be
set to ELEC (see Fig. 1) If your system is a single stage, the
switch must be set to GAS. The switch setting must agree with
the system configuration selected in the configuration menu.
For proper disposal of a product containing mercury or a
sealed container of spilled mercury, place it in a suitable
shipping container. Refer to www.thermostat-recycle.org
for location to send product containing mercury.
BATTERY LOCATION
“AA” Alkaline Batteries
ATTACH THERMOSTAT BASE TO WALL
1. Remove the packing material from the thermostat. Gently
pull the cover straight off the base. Forcing or prying on the
thermostat will cause damage to the unit.
2. Place base over hole in wall and mark mounting hole
locations on wall using base as a template (see Fig.1).
Two “AA” alkaline batteries are installed in your thermostat with
a battery tag to prevent power drainage. Prior to use, open
the battery door and remove the battery tag. To open, pull
the battery door as shown by the arrow and lift open. The two
“AA” batteries will operate all functions or maintain time and
continuously display the temperature during a loss of AC power.
To replace batteries, pull the battery door shown by the arrow
and lift open. Using the polarity indicated inside the battery
door, insert the batteries. To close the battery door, swing the
door down while pulling in the direction of arrow. Once fully
down, snap the door back into position.
3. Move base out of the way. Drill mounting holes.
4. Push wires through opening in thermostat base.
5. Fasten base loosely to wall using two mounting screws.
Place a level against bottom of base, adjust until level,
and then tighten screws. (Leveling is for appearance only
and will not affect thermostat operation.) If you are using
existing mounting holes, or if holes drilled are too large and
do not allow you to tighten base snugly, use plastic screw
anchors to secure subbase.
Thermostat can be powered by system AC power or Battery. If
isdisplayed, thethermostatisbatterypowered.If isnot
displayed, thermostat is system powered with optional battery
6. Connect wires to terminals on base using appropriate
wiring schematic (see figs. 2 through 4).
back-up. When battery power remaining is approximately half,
the
install fresh“AA”alkaline batteries immediately.For best results,
use new premium brand alkaline batteries such as Duracell® or
Energizer®. We recommend replacing batteries every 2 years.
If the home is going to be unoccupied for an extended period
7. Push excess wire into wall and plug hole with a fire-resistant
material (such as fiberglass insulation) to prevent drafts
from affecting thermostat operation.
will be displayed. When “Change
” is displayed,
O/B TERMINAL SWITCH SELECTION
(over 3 months) and
is displayed, the batteries should be
The O/B switch on this thermostat is factory set to the “O”
position. This will accommodate the majority of heat pump
applications, which require the changeover relay to be
energized in COOL. If the thermostat you are replacing or the
heat pump being installed with this thermostat requires a “B”
terminal, to energize the changeover relay in HEAT, the O/B
switch must be moved to the “B” position.
replaced before leaving. When less than two months of battery
life remain, the setpoint temperature will offset by 10 degrees
(10 degrees cooler in Heat mode / 10 degrees warmer in Cool
mode). If offset occurs, the normal setpoint can be manually
reset with
or
. Another offset will occur within two
days if batteries are not replaced. To replace the batteries, set
system to OFF.
2
| General | Details |
|---|---|
| Name | COPELAND 1F86-0244 Blue 2 Inch Single Stage Thermostat Instruction Manual |
| Make | Copeland |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.34 MB |
(1 votes, average: 5.00 out of 5)
Loading...
COPELAND 1F95G-1235GC Humidity Universal Thermostat Instruction Manual
COPELAND ST55 Sensi Smart Thermostat Instruction Manual
COPELAND 1F76U-22WFB Series Sensi Lite Smart Thermostat Installation Guide
COPELAND 026-1739 Programmable Touchscreen Thermostat User Manual
COPELAND P-N 810-1600 Programmable Touchscreen Thermostat User Guide
ESi Controls ESRTP4TOUCH Programmable Room Thermostat Instruction Manual
seitron 039790 WiFi WiTime Wall Programmable Thermostat User Guide
HEATIT Z-TEMP3 Thermostat User Guide
GENERAL LIFE 230S RF Digital Room Thermostat User Manual
AURATON Libra U Wireless Digital Room Thermostat User Manual
GENERAL LIFE HT250 RF Wireless Room Thermostat User Manual
EPH CONTROLS 20221026 RFRA – RF Room Thermostat Instruction Manual
Guangzhou XR-01 Central Air Conditioning Thermostat User Manual
Danfoss 088U0211 Public Room Thermostat Instructions
AuVerte C501 Thermostat Installation Guide