TRANE BAYECON089A Programmable Touch Screen Thermostat Instruction Manual

1

2

2

1

Bubbled letters correspond to the letters indicated in each section title.  

D

E

F

I

Time Setup  

J

Setpoint display  

from top clockwise:  

To set time:  

Setup/Programming Instructions  

1.From the Home screen (typical Home screen shown in Panel 1), touch  

to activate the Time Setting Mode. The LCD screen displays hours:minutes  

(with the hours blinking to indicate it is selected) and either AM or PM as  

shown:  

• Increment • Fahrenheit/Celsius  

• Decrement • Override hourglass  

• Cool/heat setpoint thermometer  

• Temperature setpoint  

Programmable Touch Screen  

Thermostat  

Order Numbers: X13511538010,  

BAYSTAT152A,THT02775  

Days of the week  

(Mo–Fr shown selected  

Sa and Su shown unselected)  



A

B



Mo Tu  

We Tu  

Fr  

2.Touch either  

or  

to switch between hours or minutes. To change clock  

to either 12-hour or 24-hour readout, refer to the Installation/Configuration  

Instructions (X39641190-01) or the Touch Screen Thermostat Installation,  

Operation, and Maintenance Manual (BAS-SVX044*-EN).  

J

From top to bottom:  

• indoor temperature in  

Fahrenheit/Celsius  

• Schedule periods  

(morning/day/  

evening/night)  

• Occupancy status  

• Clock  

3.Touch  

or  

to increment or decrement the hours/minutes. Touch  

and hold either button for more than 1 second to fast scroll through values.  

4.Touch  

to save and exit Time Setting Mode.  

Note: A 20-second time out will also save and exit Time Setting Mode.  

5.Touch  

to exit without saving any changes.  

• AM/PM  

• DAYS  

• HOURS  

C

Heat indicator,  

Cool indicator  

Dehumidify Setup  

D

E

F

Illustration shows a typical Home screen display.  

Note: Any graphics shown in red are only for emphasis in this  

document and do not represent the actual thermostat display  

screen colors.  

D

Note: This function is displayed only for systems configured with dehumidify  

enabled. Refer to the Installation/Configuration Instructions (X39641190-01),  

and Option Number 0200.  

From left:  

I

Outdoor temperature/  

humidity display  

from top to  

• Left arrow adjustment  

• Filter change  

X39641189-01  

To set dehumidification setpoint:  

• Touch screen lock  

• Configuration/test  

• Right arrow adjustment  

bottom:  

SAFETY WARNING  

• Outdoor temperature  

in Fahrenheit/Celsius  

1. Touch  

to activate the Dehumidify Setting Mode. The LCD screen  

F

Only qualified personnel should install and service the equipment. The installation,  

starting up, and servicing of heating, ventilating, and air-conditioning equipment can  

be hazardous and requires specific knowledge and training. Improperly installed,  

adjusted or altered equipment by an unqualified person could result in death or  

serious injury. When working on the equipment, observe all precautions in the  

literature and on the tags, stickers, and labels that are attached to the equipment.  

displays the current humidity setpoint with adjustment arrows.  

H

G

Confirm  

E

• Increase humidity setpoint  

• Humidity display  

• Decrease humidity setpoint  

2. Touch  

or  

to increment or decrement the humidity setpoint by 1%  

Screen  

cleaning  

timer  

From left:  

Top clockwise:  

increments. Touch and hold either button for more than 1 second to fast scroll  

through values.  

• System mode  

• Fan mode  

• Clock mode  

• Setpoint mode  

• Cancel  

Note: Dehumidification setpoint can be adjusted from 30% to 80%.  

3. Touch  

to save and exit Dehumidify Setting Mode.  

• Schedule  

August 2022  

BAS-SVN202D-EN  

©2022 Trane  

3

6

5

4

Note: A 20-second time out will also save and exit Dehumidify Setting Mode.  

Note: Desired settings are also activated after a 20-second time out.  

B

C

E

G

I

F

Resetting Filter Change Indicator  

Timed Override (TOV)  

4. Touch  

to exit without saving any changes.  

TOV can be used to temporarily override the scheduled temperature setpoint  

and/or fan settings. There are two ways to enter TOV Mode from the Home  

screen:  

Filterchangeindicateswhenthesystem filtertimerhasexpired. Thefiltericonwill  

blink continuously 1.5 seconds ON and 0.5 seconds OFF from the Home screen  

or TOV active screen until reset.  

• ToCanceltheTOVtimeperiod, touch  

atanytimetocancelandexitTOV  

Mode.  

System Mode Setup  

E

F

G

• Quick TOV; Touch the Occ (  

) or Unocc (  

) icon from the Home screen.  

General Notes:  

To reset the filter change indicator, press and hold both left and right arrows at  

the same time for 3 seconds. (Refer to the image below and to Panel 2 for the  

location of these icons.)  

Note: All system icons may not be available– this is configuration setup  

dependent. Refer to the Installation/Configuration Instructions  

(X39641190-01), and Option Number 0130.  

A TOV session will start up using the last occupied schedule setpoint  

settings, the last occupied fan setting, and the default TOV time period  

(Option Number 0230). Touch OK or wait for a 20-second time out to put the  

thermostat into quick TOV Active Mode; OR  

• TOV setup has three modes: TOV Setpoint Setup, TOV Time Setup, and  

TOV Active.  

To set the system mode:  

• If Fan is enabled, then TOV Fan setting can be changed in either TOV  

Setpoint Mode or TOV Time Setting Mode.  

• If a TOV is in active status, then those TOV settings become the starting  

setpoints if entering into a new User Configurable TOV session.  

1. Touch  

area to activate the System Mode setup. All system mode  

• User Configurable TOV; Touch either the Up or Down arrow to blink the  

setpoint for 20 seconds. Touch the Up or Down arrows within 20 seconds to  

change the setpoint and put the thermostat into TOV Setpoint Change  

Mode; OR   

Touch the Fan to blink the present Fan setting for 20 seconds. Touch the Fan  

area within 20 seconds to change the Fan setting and put the thermostat into  

TOV Setpoint Change Mode.  

Note: Default setting for filter replacement is one (1) month. To change the  

settings available (from Option Number 0130) are visible with the current  

system setting blinking. Each touch in the system selection box will step to the  

next available setting as shown in Figure 1.  

duration, refer to Installation Configuration Option 0275.  

• Fan icons do not display on the LCD screen if the system is not configured  

for fans.  

Fan Mode  

E

F

G

Figure 1. System selection box  

Note: The fan is only displayed on systems configured with the fan enabled.  

If disabled, then the fan icon on the LCD screen is not visible. The Fan  

modeistypicallyconfiguredinScheduleSetup(refertoScheduleSetup,  

Panel 7). Fan mode changes (as described here) from the Home screen  

initiates a temporary override (TOV).  

• The  

confirm icon is not displayed when the user is in TOV Active Mode.  

• When starting/activating TOV, the displays solid indicating that TOV is  

ACTIVE.  

OFF  

InTOVSetpointChangeMode, further adjustmentscanbemadetothesetpoint  

or Fan mode with the Up, Down, or Fan areas.  

Emergency Heat  

Heat  

Cool  

Auto H/C  

Off  

• Quick TOV Active Mode will show Occ (  

) icon while User Configurable  

TOV Active Mode Occ/UnOcc will be blank.  

Note:ForAutoH/Csystems, usethecoolmodeicon(  

) orthe heatmodeicon  

2. Choose a system mode and then either touch  

save the system mode setting and return to the Home screen.  

Notes:  

or a 20-second time out will  

To enter fan mode:  

(

) to toggle between cool and heat setpoints respectively.  

• In Quick TOV Active Mode, the typical display will show the TOV time  

remaining as HH:MM (Hours:Minutes) for 45 seconds. After the 45 seconds,  

the display will cycle to Time of Day with AM/PM for 10 seconds, followed by  

HH:MM for 5 seconds, and continue repeating Time of Day and HH:MM until  

time expires or Cancel.  

1. Touch  

will blink.  

Note: Touching  

areatoactivatetheFanDisplayModeandtheactiveFanmode  

• To adjust the TOV time period:  

• Touch the clock icon ( ) to enter TOV Time Setup Mode. The left/right  

arrow ( or ) will toggle between Days/Hours and the middle  

Up/Down arrows (  

Note: A second touch of the clock icon (  

• Touching another active area on the display screen (such as clean screen,  

clock, humidity, or schedule) will also save the system mode setting selected  

in Step 2 and activate the newly selected system setting.  

,

, another active area, or a 20-second time out will  

return to the Home screen without making changes to the fan.  

or  

) will increment or decrement the time.  

2. Next, touch in the fan selection box to put the thermostat in TOV Timed  

• Touching Cancel (  

changes.  

) will exit system mode setup without saving any  

• In User Configurable TOV Active Mode, the typical display will show  

DD:HH (DD is days and HH is Hours). After the 45 seconds, the display will  

cycle to Time of Day with AM/PM for 10 seconds, followed by Days (for 3  

seconds)if1dayormoreTOVtimeleft, HH:MM(for5seconds), andcontinue  

repeating Time of Day, Days, and HH:MM until time expires or Cancel.  

• During a power outage, if the unit was in TOV mode, it will return to the last  

TOV settings when power is returned.  

) will put the thermostat into Hold  

Override Mode and to step to the next available setting as shown below.  

Mode which holds the TOV settings indefinitely until canceled by the user.  

Additional touches of the clock icon (  

between DAYS/HOURS and Hold.  

) will toggle the thermostat  

• Toggle back to readjust the setpoint(s) by touching the thermometer icon  

).  

• Touch  

by a solid non-blinking hourglass ( ).  

Auto Mode:  

Auto Flashes  

On Mode:  

Arrows Flash  

(

3. Refer to the section, Timed Override (TOV) Setup (Step 3) in Panel 5, for the  

next actions or touch to cancel and return to the Home screen.  

area to activate the desired settings. Active TOV is indicated  

• TOV is not available in non-programmable mode (refer to Installation Option  

Number 0140).  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	TRANE BAYECON089A Programmable Touch Screen Thermostat Instruction Manual
Make	Trane
Language	English
Filetype	PDF (Download)
File size	1.49 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• Trane

TRANE BAYECON089A Programmable Touch Screen Thermostat Instruction Manual Overview

Summary of Contents

• Page 1: Time Setup To set time: From the Home screen, touch to activate the Time Setting Mode. The LCD screen displays hours:minutes with the hours blinking to indicate it is selected. Setup/Programming Instructions Touch either to switch between hours or minutes. To change clock to either 12-hour or 24-hour readout, refer to the Installation/Configuration Instructions. Dehumidify Setup Touch to activate the Dehumidify Setting Mode. The LCD screen displays the current humidity setpoint with adjustment arrows. Safety Warning Only qualified personnel should install and service the equipment. Improper installation can result in death or serious injury. Resetting Filter Change Indicator To reset the filter change indicator, press and hold both left and right arrows at the same time for 3 seconds. Timed Override (TOV) TOV can be used to temporarily override the scheduled temperature setpoint and/or fan settings. System Mode Setup Touch area to activate the System Mode setup. All system mode settings will be displayed. Fan Mode The fan is only displayed on systems configured with the fan enabled. If disabled, then the fan icon on the LCD screen is not visible. Quick TOV Active Mode The typical display will show the TOV time remaining as HH:MM for 45 seconds. User Configurable TOV Active Mode The typical display will show DD:HH (DD is days and HH is Hours) until time expires or Cancel.
• Page 2: Schedule Setup Schedule Display Mode is used to view current settings such as setpoints, periods, and day of the week. In Schedule Display Mode, the user cannot change settings. To enter Schedule Display mode, touch the icons from the Home screen. The current period will blink when viewing its schedule. Day/Period/Time Schedule Change Mode is used to select the day, day group, multiple day groups, period times, fan, and occupancy. Default settings are configured using Installation Option Numbers. To change day/period/time, touch the desired weekday icon. Selecting OK will save changes and Cancel will remove any changes since the last save. Setpoint Schedule Change Mode is used to set the heat and/or cool setpoint, occupancy, and fan settings for the selected day or day group. Touching Cancel will cause all changes after the last save to be lost.