Home > STIEBEL ELTRON > STIEBEL ELTRON FEB 2.1 Programming Thermostat Installation Guide

STIEBEL ELTRON FEB 2.1 Programming Thermostat Installation Guide

OPERATION | INSTALLATION  
Appliance description  
- The qualified contractor is responsible for adherence  
to all applicable regulations during installation and  
commissioning.  
f Fit the appliance to an internal wall, but not in a recess.  
f Never cover the appliance with curtains, etc.  
f Ensure the device is not directly exposed to external heat  
- The appliance should only be operated once it is fully in-  
stalled and all safety equipment has been fitted.  
sources (e.g. the sun, central heating or a TV set).  
f Avoid direct draughts coming from windows and doors.  
- Protect the appliance from dust and dirt during building  
work.  
8. Installation  
For installation, remove the appliance from the wall mounted  
enclosure:  
2.3 Test mark  
See type plate on the appliance.  
A
3. Appliance description  
The programming unit enables convenient operation and the dis-  
play of system parameters from the living space. Communication  
is via i²C bus. The programming unit is installed on a surface box.  
f Release the locking tab found in the opening on the under-  
side of the wall mounted enclosure. Press the locking tab  
with a screwdriver.  
8.1 Installation as an external programming unit  
f Route a 4-core bus cable from the ventilation unit to the  
mounting position of the programming unit. Use a screened  
electronic cable such as LiYCY 2x2x0.8 mm². Do not route the  
cable parallel to a three-phase cable.  
4. Operation  
See the operating instructions for the ventilation unit for infor-  
mation on operation.  
The BUS cable must protrude 20 to 30 cm out of the wall to allow  
installation.  
Installation with a flush box  
For securing to a wall we recommend using a flush box, which can  
hold the part of the bus cable protruding from the wall.  
INSTALLATION  
f Make sure that the screws supporting the flush box are ar-  
ranged either vertically or horizontally opposite one another.  
5. Safety  
Only a qualified contractor should carry out installation, commis-  
sioning, maintenance and repair of the appliance.  
f Route the bus cable through the aperture in the wall mount-  
ed enclosure from the back.  
Installation without a flush box  
f To secure the wall mounted enclosure, drill four holes  
5.1 General safety instructions  
(Ø 5 mm).  
We guarantee trouble-free function and operational reliability only  
if original accessories and spare parts intended for the device are  
used.  
f When routing the BUS cable, be careful not to damage the  
cable when drilling the fixing holes.  
In the area around the power cable entry (behind the wall mount-  
ing enclosure), a reservoir needs to be made to hold 20 to 30 cm  
of data cable.  
5.2 Instructions, standards and regulations  
B
Note  
Observe all applicable national and regional regulations  
and instructions.  
f Break out one of the knock-outs in the wall mounted  
enclosure.  
f Route the bus cable through the aperture from the back.  
6. Appliance description  
Installing the wall mounted enclosure  
C
Standard delivery  
1 Flush box  
- Fixing materials  
f Secure the wall mounted enclosure to the flush box or to the  
wall using the screws provided.  
7. Preparation  
Electrical connection  
Installation site  
f Connect the bus cable to the ventilation unit. See the installa-  
The length of the bus cable between the programming unit and  
ventilation unit must not exceed 20 m.  
tion instructions for the ventilation unit.  
Observe the following installation location requirements to ensure  
correct function.  
10|FEB 2.1  
GeneralDetails
NameSTIEBEL ELTRON FEB 2.1 Programming Thermostat Installation Guide
MakeSTIEBEL ELTRON
LanguageEnglish
FiletypePDF (Download)
File size2.08 MB
Download PDF
1 Star2 Stars3 Stars4 Stars5 Stars (1 votes, average: 5.00 out of 5)
Loading...
Stiebel Eltron RTA-3000 S2 Thermostat Installation Guide
Stiebel Eltron RTA-3000 S2 Thermostat Installation Guide

STIEBEL ELTRON FEB 2.1 Programming Thermostat Installation Guide