Home > Network Thermostat > network thermostat NetX X5-CFA Universal Setback Thermostat Instruction Manual
network thermostat NetX X5-CFA Universal Setback Thermostat Instruction Manual
BEFORE YOU START
THERMOSTAT CALLOUT
THERMOSTAT LOCATION
6
7
Please read entire install manual. The thermostat will need to
be correctly wired and configured for proper operation. Basic
HVAC configuration can be performed from the thermostat
touchscreen and advanced settings are accessed via your
network and/or the Internet.
To ensure proper operation, the thermostat should be
mounted on an inside wall in a frequently occupied area of the
space. In addition, its position must be at least 18” (46 cm)
from any outside wall, and approximately 5’ (1.5 m) above the
floor in a location with freely circulating air of an average
temperature.
NetX™ X5-CFA
Thermostat
INTRODUCTION
Be sure to avoid the following locations:
UNIVERSAL SETBACK THERMOSTAT
INSTALLATION AND PROGRAMMING MANUAL
FOR CHICK-FIL-A
1
The X5-CFA thermostat is a network capable color touchscreen
thermostat with an advanced remote sensor bus, designed for
new or replacement commercial applications. It supports up to
3 Heat / 2 Cool heat pumps and 2 Heat / 2 Cool conventional
systems.
● Behind doors or in corners where freely circulating air is
unavailable
11
12
13
14
15
● Where direct sunlight or radiant heat from appliances might
affect control operation
2
3
4
5
● On an outside wall
The X5-CFA includes an integrated XBus communications port
that allows wired (XBus) communications when used with an
NT-IPXB.
● Adjacent to, or in line with, conditioned air discharge grilles,
stairwells or outside doors
● Where its operation may be affected by steam or water
pipes or warm air stacks in an adjacent partition, or by any
unheated / uncooled area behind the thermostat
● Where operation may be affected by lighting dimmers
● Where operation will be affected by the supply air of an
adjacent unit
Core Features
● Beautiful Color Touchscreen Display
● No batteries required – always remembers setpoints
● Electronic heat anticipation and cooling droop
● Built-in short cycle equipment protection during normal
operation
● Near electrical source interference such as arcing relay
contacts
● Tamper proof electronic keyboard lockout with
programmable override ranges and time
● Preprogrammed fan operation
8 9
10
MOUNT THERMOSTAT BACKPLATE
BEFORE YOU BEGIN: Turn off the power to the HVAC
equipment.
1
2
3
4
5
6
7
8
9
Special Status Notifications
Current Equipment Mode Indicators
Lock Icon
Current Operation Status Icons
LED Filter and Fault Icons
Remote Sensor Display (Indoor, Outdoor and AUX sensors)
● Auto or Manual heat/cool changeover
● Dual Heating and Cooling Setpoints
for Occupied and Unoccupied operation
● Selectable Fahrenheit or Celsius temperature display
● Integrated Humidity Sensor
TIP: If you are replacing an existing thermostat, take a
B
WWW.NETWORKTHERMOSTAT.COM
TABLE OF CONTENTS
picture of the thermostat wiring for reference.
1. From the factory, the thermostat faceplate is not firmly
connected to the backplate. While holding the thermostat,
firmly near the bottom, gently pull apart the backplate from
the faceplate.
● Supports up to 11 Remote Sensors: up to 6 indoor, 1
humidity, 1 outdoor, and up to 3 auxiliary sensors for
monitoring items such as supply air, return air, walk-in
refrigerators and freezers, etc.
Dot Matrix Display
Mode Button
Fan Button
Before You Start
Introduction
What is in the box?
Copyright Notice
1
1
1
1
1
1
1
2
2
2
2
3
3
3
4
4
4
4
4
2. Place the rectangular opening in the backplate over the
equipment control wires protruding from the wall. Use the
backplate as a template and mark the location of the two
mounting holes.
● 2 Digital Inputs for Fault Conditions, including Condensate
and Equipment Faults
10 Resume/Cancel Button
11 Current Temperature Display
12 Up Button (Up Arrow)
13 Down Button (Down Arrow)
14 Back Button (Left Arrow)
15 Accept Button (Right Arrow)
WHAT IS IN THE BOX?
Thermostat Callout
3. Use the supplied anchors and screws for mounting on
drywall or plaster; drill two 3/16” (5mm) diameter holes at
the marked locations; tap the nylon anchors in flush to the
wall surface and fasten backplate using the supplied screws.
● (1) X5-CFA Thermostat Faceplate
● (2) 3/16 Drywall anchors
● (2) Mounting Screws
Thermostat Location
Mount Thermostat Backplate
Thermostat Setup
Installer Menu
Features
● (1) Installation Manual
WARNING: Do not over tighten the screws!
C
4. Connect the wires from your system to the thermostat
terminals as shown in the Wiring Diagrams section of this
manual. Carefully dress the wires so that any excess is
pushed back into the wall cavity or junction box. Ensure that
the wires are flush to the plastic backplate. The access hole
should be sealed or stuffed to prevent drafts from affecting
the thermostat.
COPYRIGHT NOTICE
This manual and its content are a copyright of Network
Thermostat - © Network Thermostat 2020. All rights reserved.
Remote Sensors
Factory Default Setpoints
Terminal Connection Callouts
Independent Power Source (REQUIRED)
Wiring Diagram Cross Reference Chart
Specifications
TWO (2) Year Limited Warranty
CA Title 24 Requirements
FCC Regulatory Information
Any redistribution or reproduction of part or all of the contents
in any form is prohibited other than the following:
1. You may print or download for your use only
2. You may not, except with our express written permission,
distribute or commercially exploit the content, nor may you
transmit it or store it in any other website or other form of
electronic retrieval system.
240292-02
| General | Details |
|---|---|
| Name | network thermostat NetX X5-CFA Universal Setback Thermostat Instruction Manual |
| Make | Network Thermostat |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.41 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Network Thermostat X7-Series Thermostat Installation Guide
Network Thermostat X7C-WIFI Smart Touchscreen Thermostat Instruction Manual
Network Thermostat X5-WIFI Smart Touchscreen Thermostat Instruction Manual
Network Thermostat NetXTM X-Series Thermostat Installation Guide
network thermostat NetX X Series Thermostat Instruction Manual
network thermostat NetX X-Series Ethernet Thermostat Owner’s Manual
network thermostat X-Series Ethernet Thermostat Instruction Manual
Network Thermostat NetX X7 Series Thermostat Instruction Manual
network thermostat X X7-WIFI Smart Touchscreen Thermostat Instructions
GENERAL LIFE HT330S RF Room Thermostat User Manual
Danfoss MBC 8000, MBC 8100 Heavy Duty Thermostat Installation Guide
STELPRO UT202NP Series Non-Programmable Electric Thermostat Owner’s Manual
Ferono FTH-30 Universal Thermostat Instruction Manual
TRANE XR102 Non-Programmable Thermostat User Guide
tado SRTX_ADAPTER Smart Radiator Thermostat Instruction Manual
Danfoss TPOne-B Electronic Programmable Room Thermostat User Guide
Expert4house BAC-1000ALNE Room Thermostat User Guide
BROUWLAND Brew Monk Fermenter Digital Thermostat Instruction Manual
Unisenza Plus Stats Wired and Wireless Thermostat Instruction Manual