Mi-Heat GH35EU Digital Greenhouse Thermostat User Manual
Do not use the unit in an easily inflammable atmosphere (e.g. in the
vicinity of fuel gas or spraybottles). Riskof explosion and fire!
Never install the unit close to water cocks, washbasins or other water
sources.
Cultivationof plants and seeds
Operatingmodes
ENGLISH
Position the sensor in the soil close to the roots. The sensor must be entirely
surrounded by soil. In large plant pots the sensor should be located in the
middle of thepot.
Itis indicated bytheyellowLEDwhethertheheator cool mode is active.
LED’s
Operating mode
red
yellow
green
DIGITAL GREENHOUSE THERMOSTAT
Do not insert any objects in the openings of the unit. Risk of injury, electric
shock or damage to the unit!
“Heat” mode selected /
set temperature reached /
heat mode off
Watertemperaturecontrol
on
off
off
generallife.com.tr
When assembling make sure that the connecting cable is not squeezed or
damaged by sharp edges. If such damage gives rise to open points on the
unit it must under no circumstances be connected to the mains supply.
Danger!
For water temperature control (e.g. in an aquarium), the sensor should be
positioned in the central layers of water. Here too the sensor must be
completely surrounded bywater.
“Heat” mode selected /
set temperature not reached/
heat mode on
on
off
off
on
off
on
off
on
on
INSTALLATION AND OPERATING INSTRUCTION
“Cool” mode selected /
set temperature reached /
cool mode off
6. Operation
Always pull the plug out of the socket before cleaning the unit. Only clean
withadry cloth.
When installing, check that the unit or mains cable is not damaged. Also
make sure that the sensor cable has not become sharply kinked as this may
impair operation.
1. Scopeof supply
1 pcs. Digital Thermostat GH-35 EU
Incl. suspension device
Removetheplug from thesocketwhenevertheunit is switched off.
If it is to be assumed that harmless operation is no longer possible, the
unit must be switched off and protected against unintentional operation,
which is thecasewhen:
“Cool” mode selected /
set temperature not reached /
cool mode on
1
2
3
6
2.Technicaldata
Display shows "---" with signal tone
Interrupted working circuit or shortcircuit
: GH-35 EU
Type of unit
– theunit or mains cable show visible damage
Display shows "LLL" with signal tone Temperature below -50°C (or -58 F)
Display shows "HHH" with signal tone Temperature above 99°C (or 210°F)
/ heat mode off
: 230 V / 50-60 Hz
: 3000 W
Powersupply
– theunit no longer operates
Max. breaking capacity
Max. switching current
Control range
4
7
8
– afterbeing stored for along timeunder unfavourableconditions
– afterheavytransport loads
: 16A
: 0 – 40°C / ± 0 – 90°F
: ± 1°C / ± 1°F
: -50°C to +99°C
-58°F to 210°F
: ± 1°C / ± 2°F
: < 1,5 W
7. Cleaning
Units that operate on mains voltage should not get into the hands of
children.
5
Distinction rate
Switchoff the thermostatbeforecleaning and removetheplug.
Do not use any grinding, etching or cleaning agents.
Measuring temperaturerange
The unit is not suitable for use in cattlebreeding areas.
These instructions for use form part of the unit and should be kept in a
safe place. If the unit is passed on to third parties these instructions for
use should also be provided.
1
2
3
Cool LED
Heat and cool mode on LED
Heat LED
6
7
8
Display / Temp indication
Heat / cool mode
On/Off button
Clean the casing with a damp cloth (not wet), vacuum cleaner or feather
duster.
Switching accuracy
Input
Neverimmersethe unit in water. Danger!
If the unit is not used for a long time it is necessary to protect it from
excessivedust and dirt.
4-5 Temperature selection buttons
: II
Protection class
Protectivesystem
Sensor length
In industrial installations the accidentpreventionregulations of the
Industrial Professional Association for Electrical Installations and
Equipment must be complied with.
: IPX4
Switching on/off
: approx.110 " /2.8m
As soon as the unit has been connected to the supply voltage it can be
switched on by means of the “ON/OFF” button. To do this, the button must
8. Disposal and repair
Never pour liquids over the unit as this presents the risk of a fire or‚ fatal
electric shock. If this should happen, however, pull the plug out of the
socketand consult aspecialist.
IMPORTANT:
Take units to be disposed of to a suitable waste
reception depot only.
be pressed for
3
seconds. Immediately after switching on, the unit
Read carefully and follow these instructions as well as the general
advice on safety and risks before installation. Keep this leaflet in a
safe place for future reference. If you have any doubt about the safety of the
unit seek the advice of an expert. If the unit is used in a greenhouse make
surethatthe electricalconnections arecarriedout byqualified personnel.
determines the ambient temperature of the sensor and indicates it on the
display. To switchoff, again pressthe“ON/OFF”button for 3 seconds.
Repairs to the unit may only be carried out by
authorised specialists. Please therefore consult
themanufactureror dealer.
If you are uncertain about correct connection, or if you haveany questions
which are not clarified in the course of the instruction, contact the
manufactureror aspecialist.
Heat/Cool mode
N.B. If the unit is not correctly repaired the
warrantywillnot be valid.
Itis possible to switchbetweenthe heatand cool mode bypressing the
This unit is not intended for use by persons (including children) with
limited physical, sensory or mental capacity. This also applies to persons
who do not have sufficient experience in or knowledge of handling the
product, unless they are being supervised or instructed in the use of the
unit byaperson responsible for theirsafety.
button. Keep the
button pressed for 3 seconds to change mode. On the
3. General
Incorrectly carried out repairs may represent a
danger to theuser and other people.
display “H” appears for 4 seconds for heating and “C” for cooling. At the
same time you can detect the mode that has been set by means of the the
red LEDstands for heating and the green LEDfor cooling.
After unpacking and before switching on, make sure that the unit and all its
accessories are perfectly in order. If there has been any damage in transit,
consult your dealer or the manufacturer immediately. Keep the packaging
materials (polythene bag, polystyrene, nails etc.) out of reach of children
because they represent a potential source of danger. This also applies to
small parts supplied, which can be swallowed. This electronic thermostat
can be used for a wide variety of temperature control applications, for
example for heating and cooling greenhouses and winter gardens, or for
monitoring water temperatures in aquariums, the air temperature in
terrariums or the soil temperature in seed beds. It is simple to operate and
can be connected to any type of heating cable, heating mat or other heating
or cooling devices, provided that the maximum heating power of 3000 W is
not exceeded. This thermostat is only licensed for connection to 230 V,
50/60Hz voltage. The unit must be protected from high degrees of
contamination and moisture. If it is used for any application other than that
described above it may be damaged and risks such as short-circuiting, fire,
electric shock etc. may ensue. The safety and installation in-structions
must be strictlyadhered to.
9. Servicing and maintenanceunderwarranty
We give you a 2 year unlimited manufacturerʼs warranty (from date of
purchase) on all Isıpark products. Excluded from the warranty is damage
due to violence, improper use and failure to follow instructions for use,
cleaning and maintenance work.
5. Installation
Settingtherequired temperature
Make sure that the mains voltage corresponds to the voltage
indicated in Chapter 2 (technical data). The place of installation
must be chosen so that the unit can under no circumstances get
Press the
or button briefly to switch to the setting mode. The already
and buttons
set temperature now flashes in the display. Using the
you can change the temperature in 1oC / 1°F steps. (Setting range -50°C to
+99°C / -58°F to +210°F). After you have set a new temperature, it is saved
automatically and the menu closes after 3 seconds. Now the display again
shows thecurrentambient temperature.
The manufacturer accepts no liability for damage due to frost, insufficient
heating power related to the room dimensions, or due to inadequate heat
insulation.
wet(e.g. dripping condensation, open roof hatches, etc.)or fall into water.
The thermostatmaybe operated in ahorizontalor vertical position.
1. Connect the heating or cooling
Important note
Celsius/Fahrenheit unit selection
The unit may only be opened and repair work may only be carried out by
licensed specialists in accordance with the applicable repair regulations.
Only original parts maybe fitted.
unit to the thermostat. To do so,
Under normal running status, short press key or
release it, it enters to temperature setting state, and it blinkingly displaysthe
current set temperature. Atthis time, hold and press “ ” keyfor more than
key and immediately
1
insert the plug of the corresponding
heating or cooling unit in the socket
on thethermostat.
A guarantee of perfect operation and reliability can only be givenif the unit is
installed and handled expertly. This also applies to the provisions of the
Technical Equipment Act and the applicable accident prevention
regulations.
5 seconds , the system enters Celsius and Fahrenheit setting state, LED
blinkingly flashes C and F. Switch between Celsius and Fahrenheit. When
finish setting, it will exit in 3s if there is no key operation, and return to the
normal running stateand savetheparametersautomatically.
2. Now connect the connecting
cable of the thermostat to a 230 V
mains socket.
4. Adviceonsafetyand risks
In case of warranty please complete the warranty and info card attached for
this purpose.
Only a 230 V, 50/60Hz mains socket in the public supply network
may be used as a power source. Never try to operate the unit at a
differentvoltage.
3. Position the end of the sensor
cable at the most suitable point for
temperaturecontrol.
If you have any further questions refer to our ISIPARK:
Tel.: +90 (850) 441 55 66 or Email: info@isipark.com.tr
Consult an expert if you have any doubts about the operation, safety or
connection of theunit.
This unit mayonly be used indoors.
Room temperaturecontrol
When opening the cover or removing parts, the unit must be disconnected
from themains supply.
The sensor should be installed at
half room height and should be
freely suspended. The room
temperature can only be optimally
controlled when the sensor is not
Neverswitchthemains plug on or off withwethands.
Never pull on the mains cable itself, always pull the plug out of the socket
bythegripping surfaces.
2
influenced by draughts, solar
radiation or other heat or cold
sources.
2
1
3
4
| General | Details |
|---|---|
| Name | Mi-Heat GH35EU Digital Greenhouse Thermostat User Manual |
| Make | MI-HEAT |
| Language | English |
| Filetype | PDF (Download) |
| File size | 1.96 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Mi-HEAT M2 Wi-fi Bluetooth Thermostat Instruction Manual
MI-HEAT E51 Thermostat User Manual
MI-HEAT MST1 Room Thermostat for Underfloor Heating User Manual
MI-HEAT MTS200 WiFi Thermostat Instruction Manual
MI-HEAT WT8 WiFi Smart Thermostat User Manual
BEOK CONTROLS TDR89 Thermostat User Guide
KeepRite TSTATIIEWF-01 Ion Gray Smart Thermostat Owner’s Manual
HEAT DECOR HD-T1000 WIFI Thermostat User Guide
STEGO ET 011 Electronic Thermostat User Manual
Honeywell Home RLV3150 Electric Thermostat
BEOK CONTROLS TFT-LCD Heating Thermostat Instruction Manual
Danfoss ECtemp Next Plus Electronic Intelligent Timer Thermostat Installation Guide
LUX TX700U Universal Thermostat Instruction Manual
GENERAL LIFE ARUNA 304S RF Digital Room Thermostat User Manual
Ouellet Canada OTH24-AFR Programmable Low Voltage Electronic Thermostat User Guide