SAVANT CLI-W220X-00 Multistat Smart Thermostat User Guide
Remove Old Thermostat
1.
Scroll through and record the current settings and
schedules from the old thermostat.
Terminal
Terminal
Wire Color
R
C
2.
3.
Switch OFF power at either the breaker panel or the
switch that controls the HVAC system.
Open the old thermostat and take a photo of the
existing thermostat and wiring. The photo should
reveal wire colors and terminal designations.
RC
4.
5.
Using the top chart to the right, add a check to record
which power wires are installed in the old thermostat.
In addition, record the wire colors. Not all fields from
the chart may be populated.
Wire Color
O
G
Remove each wire recorded and attach a label
that matches the terminal designation from the old
thermostat. It’s important to label the wires according
to the terminal designation and NOT the color of the
wire.
Y2
Y1
W2
W1
6.
7.
Using the bottom chart to the right, add a check to
record which HVAC signaling wires are installed in the
old thermostat. In addition, record the wire colors.
Remove each wire recorded above and add a wire
label to each.
HELPFUL! Additional information on the terminal
designators and how to wire the thermostat into
different types of HVAC systems is available in the
Multistat Smart Thermostat Deployment Guide
(009-1959-xx) available on the Savant Customer
Community.
TIP! Wrap wires around a pencil or similar to prevent
the wires from falling back into the wall
8.
Remove old thermostat from wall.
Location and Mounting Overview
For new installations or when relocating the thermostat, follow the guidelines below:
–
Locate thermostat on an inside wall away from windows and doors to reduce the exposure to drafts or direct
sunlight.
–
–
–
–
–
–
Do not locate where air circulation is poor such as in a corner or behind a door.
Install away from any heating conditions such as near a radiator register, vent, or fireplace.
To adhere to ADA requirements, install thermostat 48 - 54 inches (1.22 - 1.37 meters) above the floor.
Height requirements can be adjusted upward to 60 inches (1.5 meters) if ADA requirements are not mandatory.
The thermostat does not need to be level to operate correctly. Leveling the thermostat is for aesthetics only.
Thermostat can be oriented in either a portrait or landscape layout.
Install Thermostat Mounting Plate
9.
Grasp the mounting plate half of thermostat in one hand,
and the LCD screen half in the other.
TIP! Grasp the bottom of the thermostat, which is the
end opposite the proximity sensor.
10. Pull the two halves apart and, at the same time, gently
rock the front and back halves back and forth until they
separate.
Pull wires through
the center opening
Bubble level slot
(Landscape)
11. Position the mounting plate onto the wall. Using a pencil,
mark the two mounting holes onto the wall (See image).
Route wires
around this area
–
Use the bubble level in the center of the mounting
plate to level when mounting using a portrait layout.
Use bubble level
when mounting
–
When mounting using a landscape layout, remove
the bubble level by pushing it out through the rear
of the mounting plate and reinstall it into the bubble
level slot on the right side of the center cutout. See
the diagram to the right.
12. With a #2 Phillips screwdriver, screw the wall anchor into
the wall on each mark made. A 5/32 inch hole can be pre-
drilled to make it easier when screwing the anchor to the
wall. Wall anchors are not required with installs that have
a sub wall to fasten to.
IMPORTANT! As indicated in the diagram above,
route the thermostat wires around the
wiring keepout. When the two halves of
the thermostat are snapped together the
component that rests in that indented area
could be damaged.
13. Pull the existing wires through the center cutout in the
mounting plate.
14. Screw the mounting plate to the wall using the supplied
screws.
Multistat Smart Thermostat Quick Start Guide | 009-2428-01
Copyright ©2025 Savant Systems, Inc 240318
2
of
8
45 Perseverance Way, Hyannis MA 02601
Savant.com | 508.683.2500
|
| General | Details |
|---|---|
| Name | SAVANT CLI-W220X-00 Multistat Smart Thermostat User Guide |
| Make | SAVANT |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.32 MB |
(1 votes, average: 5.00 out of 5)
Loading...
SunTouch SunStat CommandPlus Programmable Thermostat Instruction Manual
King Electric K322E Electronic Non Programmable Thermostat Instructions
ELKO ep TER-4 Double Thermostat Owner’s Manual
MI-HEAT MST1 Room Thermostat for Underfloor Heating User Manual
Smith s HAGA95001 Remote Wired Room Thermostat Owner’s Manual
seitron TAD022 Digital Room Thermostat for Heating Cooling System Instruction Manual
CIELO BM101WA Breez Max Smart Thermostat Installation Guide
ideal HEATING Halo Lite RF Combi Wi-Fi Wireless Boiler Thermostat Instructions
HYSEN HY02DB-WIFI Wifi Plug In Thermostat User Manual
Honeywell Home X1N Non Programmable Thermostat Installation Guide