Home > HVAC > HVAC Electrical Heating Thermostat M5.XX Installation Guide

HVAC Electrical Heating Thermostat M5.XX Installation Guide

2

M5.XX Electrical Thermostat

Mounting Manual

supply (e.g. power supply for heating cable) for avoiding the

interference of voltage signal to the heating thermostat. If there is

shielded cable in the extended cable, shielded cable should not be

connected to ground but to terminal 7. It is recommended that the

extended cable and casing should not be shared with others.

International Standard Electronic Heating

Thermostat Characteristics:

Mounted on the surface of the wall indoors

Temperature control range +5/+40℃

Applied in the auto-control system of space

heating

Outer sensor and its resistance:

LED turned on while heating

Satisfying the requirements of safety, energy

saving and comfort.

Temperature(℃)

Resistance(Ω)

22070

17960

Types Table：

12091

Types

Load

Current

Methods of

Temperature

Measurement

Outside Sensor

8312

Applications

5827

Mounting Location Recommended：

M5.03

The heating thermostat should be mounted on the wall with

air flowing freely around.

Inside Sensor

M5.03I

Outside

M5.03D

M5.16

Warning: The mounting location should not be influenced by

other heat source (e.g. sunlight), air flow through doors &

windows or temperature of outer wall.

Heating cable and

other power heat

loads

Inside Sensors

Outside Sensor

M5.16I

16A

Inside Sensor

Outside

M5.16D

Inside Sensors

Technique Parameters：

Voltage: 220VAC

Power consumption: 5VA

Temperature control range: 5~40℃

Temperature limit range: 25~55℃

Power save mode temperature: 5℃

Temperature deviation: 0.5K

Ambient temperature: -5~50℃

Degree of protection provided by enclosure: IP20

Outer sensor: length of cable 3m

Specification：

Temperature Set：

The factory default of temperature control range is +5/+40℃.

For convenient adjusting the LED will be turned on while heating.

For the first use, please set the thermostat at the highest

temperature, when the room or floor temperature approaches the

expected, please turn the knob back until the LED is turned off.

One or two days after, user could do fine turning if necessary.

Handling Instruction：

ꢀ on and off

：

off

ꢂ

ꢁ

ꢂ

temperature set

5~40

indicator

：

℃

：

LED turned on while

heating.

ꢁ

ꢀ

Mounting of Outer Sensor：

℃

Please place the casing under the floor with the outer sensor

in, the terminal of which should be thickened and placed on the

top of the concrete layer. Sensor cable can be extended to 50m

with other cables if necessary. If multi-core cable is used as

extended cable, extra cable core should not be used for power

German OshlandAutomatic Technology Co., Ltd.

Electrical Heating Thermostat

HVAC CONTROLS PRODUCTS

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	HVAC Electrical Heating Thermostat M5.XX Installation Guide
Make	HVAC
Language	English
Filetype	PDF (Download)
File size	0.11 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Comments are closed.

HVAC Instructions & User Manuals

Get the free PDF manual for the HVAC Electrical Heating Thermostat M5.XX Installation Guide and access setup steps, usage instructions, and troubleshooting tips. 👉 View online or download now to keep your thermostat running smoothly!

Electrical M5.XX Manual: Questions and Answers

Electrical M5.XX specifications

Power supply	220VAC
Setpoint range	5~40℃
Operating temperature	-5~50℃
Power consumption	5VA

Full specifications, page 1

Can I extend the outer sensor cable on the Electrical M5.XX beyond its standard length?

Yes, the sensor cable can be extended up to 50m using other cables if necessary. If multi-core cable is used as the extension, extra cable cores should not be used for power. Installation Guide, p. 1

What should I do with shielded cable in the extended sensor cable for the Electrical M5.XX?

Connect shielded cable to terminal 7, not to ground. Installation Guide, p. 1

Where should the outer sensor be positioned on the Electrical M5.XX installation?

Place the sensor casing under the floor with the outer sensor inside. The sensor terminal should be positioned on top of the concrete layer. Installation Guide, p. 1