Honeywell Home T834 Series Thermostat Owner’s Manual

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

Owner’s Manual  

English: Page 1  

Mode d’emploi  

Français: Page 6  

Manual de Uso  

Español: Página 11  

M24922  

T834 Series  

Thermostat  

This manual covers the following models:  

Horizontal Mount: T8034N • Vertical Mount: T834N/T834L  

Pre-installation checklist  

Check package contents:  

Before you begin, make sure you  

have:  

•

•

Thermostat  

•

No. 2 Phillips & small pocket  

Wall anchors & screws (2 each)  

screwdrivers  

•

•

•

•

Hammer  

Level (optional)  

Pencil  

Drill and bit (3/16” for drywall, 7/32” for  

plaster)  

Must be installed by a trained, experienced technician  

Read these instructions carefully. Failure to follow these instructions  

can damage the product or cause a hazardous condition.  

CAUTION: ELECTRICAL HAZARD  

Can cause electrical shock or equipment damage. Disconnect power before  

beginning installation.  

MERCURY NOTICE  

If this product is replacing a control that contains  

mercury in a sealed tube, do not  

place the old control in the trash. Contact your  

local waste management authority for instructions  

regarding recycling and proper disposal.  

69-2083EFS-03  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	Honeywell Home T834 Series Thermostat Owner’s Manual
Make	Honeywell Home
Language	English
Filetype	PDF (Download)
File size	0.69 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• Honeywell Home

Honeywell Home T834 Series Thermostat Owner’s Manual Overview

Summary of Contents

• Page 1: Owner’s Manual This manual covers the following models: Horizontal Mount: T8034N, Vertical Mount: T834N/T834L Pre-installation checklist Check package contents: Before you begin, make sure you have: Thermostat, No. 2 Phillips & small pocket screwdrivers, wall anchors & screws (2 each), hammer, level (optional), pencil, drill and bit (3/16” for drywall, 7/32” for plaster) Must be installed by a trained, experienced technician Read these instructions carefully. Failure to follow these instructions can damage the product or cause a hazardous condition. CAUTION: Electrical hazard can cause electrical shock or equipment damage. Disconnect power before beginning installation. Mercury notice: If this product is replacing a control that contains mercury in a sealed tube, do not place the old control in the trash. Contact your local waste management authority for instructions regarding recycling and proper disposal.
• Page 2: T834 Series Product application This thermostat provides control of 24 Vac single-stage heating and cooling systems. System Types Specifications Gas, oil, or electric heat with air conditioning Temperature Range 50° to 90°F (10° to 32°C) Operating Ambient Temperature 0° to 120°F (-18° to 49°C) Operating Relative Humidity 5% to 90% (non-condensing) Dimensions (vertical model) 2.88W x 4.75H x 1.5D (inches) Fan Settings Auto, On Electrical Ratings
• Page 3: Base installation involves pulling wires through the wire hole, positioning the base on the wall, leveling it, and marking hole positions. Drill holes appropriate for the wall type and tap in supplied wall anchors. Pull the wire through the base, position it over the anchors, and tighten the mounting screws. Wiring requires loosening screw terminals, inserting bare wires beneath the screws, and re-tightening them. Excess wire should be pushed back into the wall opening, and the opening should be plugged with nonflammable insulation to prevent drafts. Terminal designations include R for heating power, Rc for cooling power, G for fan relay, W for heat relay, and B for heat pump changeover valve energized in heating. In a single-transformer system, keep the metal jumper between R and Rc; remove it for a two-transformer system. For heat pump systems, connect terminals W and Y with a small piece of wire. Y is for compressor contactor, and O is for heat pump changeover valve energized in cooling. Use 18-gauge thermostat wire; shielded cable is not required.
• Page 4: T834 Series Set fan switch (except model T834L) Fan operation settings: F: For gas or oil heating systems, leave the fan operation switch in this factory-set position. E: Change the switch to this setting for heat pump or electric heat systems. Set heat anticipator (except model T834L) Move the adjustment arrow to the proper setting for your system. Thermostat mounting Align the slots on the cover with tabs on the sides of the base, then push gently until the cover snaps into place.
• Page 5: Operation Fan switch System switch On: Fan runs continuously. Cool: Controls the cooling system. Heat: Controls the heating system. Off: All systems are off. Auto: Fan runs only when heating or cooling system is on. Temperature setting: Adjust to set desired indoor temperature. Caution: Equipment damage hazard Do not operate cooling system when outdoor temperature is below 50°F (10°C).
• Page 6: Owner’s Manual Thermostat Employez ce manuel pour les modèles suivants : Modèle Horizontal : T8034N Modèle Vertical : T834N/T834L Éléments nécessaires à l’installation Vérifiez le contenu de paquet : Outillage et matériel nécessaires : Il est impératif de faire réaliser l’installation par un technicien chevronné Lisez attentivement les présentes consignes. La non observation de celles-ci risque d’endommager le produit ou de présenter des dangers. MISE EN GARDE : RISQUE ÉLECTRIQUE AVIS CONCERNANT LE MERCURE
• Page 7: Application du produit Ce thermostat est prévu pour réguler des systèmes de chauffage et de climatisation à une zone de 24 V ca (secteur). Types d’installations Chauffage au gaz, au mazout ou électrique avec climatisation. Fourchettes de température 10 à 32° C (50° à 90° F). Température d’expédition -18° à 49° C (0° à 120° F). Humidité relative de fonctionnement 5% à 90% (sans condensation). Dimensions (modèle vertical) 2.88”W x 4.75”H x 1.5”D. Réglages du mode Heat, Off, Cool (T834N). Dimensions (modèle horizontal) 4.75”W x 2.88”H x 1.5”D. Réglages du ventilateur Auto, On. Caractéristiques Électriques Tension (50/60Hz) 20-30 Vca.
• Page 8: T834 Series Montage de la plaque Tirez les fils par l’ouverture de la plaque. Placez la plaque sur le mur, mettez-la à niveau et marquez la position des trous. Percez des trous (3/16 pour la cloison sèche, 7/32 pour le plâtre), puis enfoncez les chevilles. Desserrez les bornes à vis, insérez les fils nus sous des vis, puis resserrez les vis. Bouchez l’ouverture du mur avec de l’isolant ininflammable pour empêcher les courants d’air de perturber le fonctionnement du thermostat. Désignation des bornes R Alimentation chauffage. Raccorder au côté secondaire du transformateur de l’installation de chauffage. Rc Alimentation climatisation. Raccorder au côté secondaire du transformateur de l’installation de chauffage. Relais de chauffage. Installations à thermopompes : raccordez les bornes W et Y par un petit morceau de fil (non fourni). Utilisez du fil à thermostat de calibre 18. Il n’est pas nécessaire d’utiliser du fil blindé.
• Page 9: Adjust the fan switch (except T834L). Options for the fan: F: For gas or oil installations, leave the switch in the factory position. E: Move the switch to this position for a heat pump or electric heating installation. Adjust the heating detector (except T834L). Move the arrow to the appropriate arrangement for your system. Your system arrangement includes steam, hot water heating, high-efficiency air, standard air, and electric air. Mounting the thermostat involves aligning the cover slots with the thermostat tabs and gently pushing until the cover snaps into place.
• Page 10: T834 Series Mode d’emploi Commutateur de ventilateur Mode de fonctionnement On : Le ventilateur fonctionne en permanence. Cool : Régule que la climatisation. Heat : Régule que le chauffage. Off : Tous les systèmes sont éteints. Auto : Le ventilateur ne fonctionne que lorsque le chauffage ou la climatisation sont en marche. Réglage de la température : Ajustez pour obtenir la température intérieure désirée. MISE EN GARDE : RISQUE D’ENDOMMAGER LE MATÉRIEL. Ne pas faire fonctionner la climatisation lorsque la température extérieure est inférieure à 10° C (50° F).
• Page 11: Owner’s manual This manual covers the following models: Horizontal model: T8034N Vertical model: T834N/T834L Pre-installation checklist Check the contents of the package: Tools and materials needed: Must be installed by a qualified and experienced technician Read these instructions carefully. Ignoring them could damage the product or create hazardous conditions. Caution: electrical hazard Can cause electric shock or equipment damage. Disconnect power before starting installation. Mercury notice If this product replaces a control containing mercury in a sealed tube, do not throw the old control in the trash.
• Page 12: T834 Series Aplicación del producto Este termostato brinda control de los sistemas de calefacción y refrigeración de una sola etapa de 24 VCA. Tipos de sistemas Especificaciones Calefacción a gas, petróleo o eléctrica Rangos de temperatura con aire acondicionado 50° a 90°F (10° a 32°C) Humedad relativa de funcionamiento 5% a 90% (sin condensación) Dimensiones (modelo vertical) Ajustes del sistema Heat, Off, Cool (T834N)
• Page 13: Instalación de placa de montaje Tire de los cables a través de su orificio. Posicione en la pared la placa de montaje, nivélelo y marque las posiciones de los orificios. Taladre orificios en las posiciones marcadas y inserte los soportes de pared suministrados. Coloque la placa de montaje sobre los soportes, inserte y ajuste los tornillos de montaje. Cableado Afloje los terminales atornillados, inserte los alambres pelados debajo de los tornillos y vuelva a ajustar los tornillos. Empuje el exceso de cable de vuelta en la abertura de la pared. Tapone la abertura de la pared con aislamiento no inflamable para evitar que las corrientes de aire afecten el funcionamiento del termostato. Designaciones de terminales R: Alimentación de calefacción. Conecte al lado secundario del transformador del sistema de calefacción. Rc: Alimentación de refrigeración. Conecte al lado secundario del transformador del sistema de refrigeración. G: Relé del ventilador. W: Relé de calefacción. B: Sistemas de bombeo de calor. O: Válvula de cambio del bombeo de calor activada durante la refrigeración. Especificaciones de cable: Use cable de termostato calibre 18. No se requiere cable blindado.
• Page 14: T834 Series Ajuste de funcionamiento del ventilador (excepto T834L) Opciones del ventilador: Para los sistemas de calefacción a gas o petróleo, deje el interruptor de funcionamiento del ventilador en la posición original de fábrica. Cambie el interruptor a esta posición para los sistemas de calefacción eléctricos o de bombeo de calor. Ajuste el anticipador del calor (excepto T834L). Mueva la flecha al ajuste apropiado para su sistema. Montaje del termostato. Alinee las ranuras de la cubierta con las lengüetas del termostato. Empuje con suavidad hasta que la cubierta calce en su lugar.
• Page 15: Instrucciones de manejo Interruptor del ventilador Interruptor del sistema On: El ventilador funciona continuamente. Cool: Controla el sistema de refrigeración. Heat: Controla el sistema de calefacción. Off: Todos los sistemas están apagados. Auto: Funciona sólo cuando está encendido el sistema de refrigeración o calefacción. Ajuste de temperatura: Resbale para fijar temperatura deseada. PRECAUCIÓN: PELIGRO DE DAÑO AL EQUIPO. No haga funcionar el sistema de refrigeración cuando la temperatura exterior sea inferior a 50°F (10°C).
• Page 16: Need help? For assistance with this product please call Customer Care toll-free. Resideo Technologies, Inc. The Honeywell Home trademark is used under license from Honeywell International, Inc. This product is manufactured by Resideo Technologies, Inc. and its affiliates.