Home > Aeotec > AeoTec Radiator Thermostat ZWA021 User Manual

AeoTec Radiator Thermostat ZWA021 User Manual

2

RAV Pin*

RAVL

3. Move Radiator Thermostat to the desired installation location.

Used in this guide.

Important safety information.

Please read this and the online guide(s) at

support.aeotec.com/trv carefully. Failure to follow the

recommendations set forth by Aeotec Limited may be

dangerous or cause a violation of the law. The manufacturer,

importer, distributor, and/or reseller will not be held responsible

for any loss or damage resulting from not following any

instructions in this guide or in other materials.

4. Set your Z-W ave gateway into its ‘add device’ mode.Refer to

the gateway’s manual if you are unsure of how to perform

this step.

Radiator Thermostat

ZW A021

Locking Ring

5. Press Radiator Thermostat’s Boost Button once. The screen

will show [ICON] to indicate that inclusion is in progress. It

will then show an ID number indicating that your thermostat

has successfully connected to your gateway. Should ERR

appear on the screen instead, your thermostat has been

unable to join the network; press the Boost Button again to

clear the error and then repeat the above steps. Please

RAV

LCD Screen

Radiator Thermostat is intended for indoor use in dry locations

only. Do not use in damp, moist, and / or wet locations.

6. W hen it is connected to your Z-W ave gateway, physically

install your thermostat upon the selected radiator. The

screen will show INS indicating that physical installation can

begin.

Quick start.

The following will step you through installing Radiator

Thermostat and connecting it to your Z-W ave network.

a. Ensure that no buttons are pressed during the following

steps.

1. Decide on the installation location of Radiator Thermostat.

Spirit Z-W ave Plus

Action Button

Botón de acción / Bouton d'action / Aktionsknopf /

Pulsante di azione / Actieknop / Åtgärdsknapp

2. Insert the 2 pcs AA LR6 batteries, paying attention to the

polarity.

b. Remove any existing radiator thermostat. Follow that

thermostat’s user guide for instructions.

Install the thermostat by screwing the metal ring to the

valve.

Diagram 2; Choose the right adapters.

c. If your valve does not fit, use the supplied adapters to

mount the thermostat.

The adapters for Danfoss RAV (pin must be plugged on the

valve tappet) Danfoss RA and Danfoss RAVL

are included.

For the following valves no adapter is required:

Heimeier, Junkers Landy + Gyr, MNG, Honeywell, Braukmann,

as these have a thread of M30 x 1.5mm.

For the following valves an adapter is required:

Diagram 1; Battery installation.

1. Herz M28 x 1.5 mm, Comap M28 x 1.5 mm, Vaillant 30.5 mm,

Oventrop M30 x 1.0 mm, Meges M38 x 1.5 mm,

Adapters for

Danfoss valves

Batteries (x2)

Screw for adapter

Bottom cover

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	AeoTec Radiator Thermostat ZWA021 User Manual
Make	Aeotec
Language	English
Filetype	PDF (Download)
File size	0.17 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Comments are closed.

Aeotec Instructions & User Manuals

Get the free PDF manual for the AeoTec Radiator Thermostat ZWA021 User Manual and access setup steps, usage instructions, and troubleshooting tips. 👉 View online or download now to keep your thermostat running smoothly!

Aeotec ZWA021 Manual: Questions and Answers

How do I start exclusion mode on the Aeotec ZWA021?

Press and hold the boost button for at least 5 seconds.

Start exclusion or unpair mode on your Z-Wave Controller first.
Press and hold the boost button on the thermostat for at least 5 seconds.
If successful, the display shows '0' and the device is unpaired.
If unsuccessful, the display shows '18' and you must repeat from step 1. User Manual, p. 2