SENNA-300-RF Digital Room Thermostat User Guide

1

2

ScreenIndicators  

Warning!  

Operations within the heating / cooling unit or the electrical installation must be  

carriedout byprofessionally qualified persons.  

ENGLISH  

1

2

8

DIGITAL ROOM THERMOSTAT  

PAIRINGTHEROOMTHERMOSTATANDTHERECEIVER  

9

10  



Primarily press the sync button of the Receiver for 2 seconds and see blinking  

greenlight oftheReceiver.  

3

4

generallife.com.tr  







While yourdeviceis turned off, pressand hold the"On/Off" button for 3 seconds.  

Pressthebutton until the“  

” menu appears.  

BATTERY PLACEMENT  

Press the “+” or “-” button of your Room Thermostat while the LED is flashing  

green.  

5

SENNA 300 RF USER MANUAL  

6

7





Ifthepairing is successful, thegreenflashing LEDon theReceiverwillbe steady.  

Receiverand Room Thermostathavebeen pairedto eachother.  

GENERALSPECIFICATIONS  

SENNA 300 RF is  

1

2

3

4

5

6

7

8

Hour Indicator  

Day Indicator  

ROOMTHERMOSTATTEMPERATURE CALIBRATION  

a

wireless room thermostat. The user can adjust the room  

Temperature sensors which are used in Room Thermostats are highly sensitive.  

You may need to calibrate your Room Thermostat if you would like to get the same  

temperaturevalueswithother thermometersin yourliving space.  

temperature with the required temperature and get more comfortable and  

economic heating/cooling.  

Room Temperature  

Set Temperature  

 Dailyand WeeklyProgramming  

Economy Mode  

Comfort Mode  





While yourdeviceis turned off, pressand hold the“On/Off“ button for 3 seconds.  

Press the "On/Off" button until the “ ” menu appears. In order to see the  

 DifferentMode Options (Comfort, Economy)  

 Heating Calibration  

ON/OFFControl  

WirelessConnection  

Weekly Program Mode  

Battery Indicator  

Heating Indicator  

desired temperature, set the temperature difference by pressing the  

 Heating/Cooling Option  

TPIAlgorithm  

As shown in the picture above, press the screwdriver forward from the space  

shown, bend the tabs and separate the front cover. Insert 2 new AAA alkaline  

batteries in the battery housing with the correct battery direction. Replace both  

batteries at the same time. Then align the frontpart of your Room Thermostat to the  

backand squeezeittowardstheback.  

“Temperature Adjustment Buttons”. This value can be arranged between “-8° C"  

 PreciseTemperatureMeasurement  

and “+8° C".  

9

- If the Heating Indicator is blinking, the heating unit is working.  

- If the Heating Indicator is steady, the heating unit is not working.  

Cooling Indicator  

SENNA 300RF AND EQUIPMENTS  

SENNA 300 RF Room Thermostat  



In order to save the settings and exit, press the "On/Off" button until the device  

turns off.  

Holder  

Alkaline  

Battery  

Note:Recommended temperaturecalibration is “0.0°C”.  

10  

- If the Cooling Indicator is blinking, the cooling unit is working.  

- If the Cooling Indicator is steady, the cooling unit is not working.  

Low Battery Warning: When the “  

” icon appears on the screen, it means “low  

battery warning”. It is recommended to replace the batteries when this warning  

appears.  

FACTORY SETTINGS RESET  

RECEIVER  

You can reset your Room Thermostat to its default factory settings. This operation  

resets the mode temperature values, calibration setting and heating/cooling  

modes to factory setting. In orderto resetyourRoom Thermostatto factory setting:  

1-Manual Operation Button:  

Warning: When the product is not used for a long period (more than 15 days), remove  

thebatteries. Otherwise, malfunctions thatmay occurwouldbeoutof warranty.  

Pleasethrowyourdead batteries into thewastebin forbatteries.  

By disabling the Receiver, it enables you to use  

your boiler manually.  

2-Pairing Button:  

1

2

3







While yourdeviceis turned off, pressand hold the“On/Off” button for 3 seconds.  

Dowels and Screws  

Receiver  

Pressthe“On/Off” button untilthe“  

While in the “ ” menu, select the “  

and pressthe“On/Off” button.  

Your devicewillbe turned off and resetto factory settings.  

” menu appears.  

Allows to pair the Receiver with the Room  

Thermostat.  

3-Receiver LED Light  

4-Receiver Power Cable Input  

5-Boiler Connection Cable Input  

RECEIVERPLACEMENT  

” option by using the “+” or “-” buttons  

The important things to note for the Receiver placement is  

avoiding physical contact between the Receiver and  

heating/cooling unit, and protecting it against materials  

such asliquid, dust etc.  



DAY ANDHOURSETTINGS  







While your Room Thermostat is on, keep pressing the “Weekly Program” button  

for 3 seconds.  

TECHNICALDATA  

Room Thermostat  

The devices should be placed in order to minimize the damage to the received and  

transmittedsignals bypayingattentiontothefollowingpoints;  

At the first screen that appears, hour part will be blinking. You may set the time  

withthe“+” and“-” buttons.  

Dimensions  

Operating Current  

85mm / 125mm / 19mm  

3V DC (2 x AAA alkaline battery)  

0.1^oC  

(5^oC) – (30^oC)  

4

5





The devicesshould not be mounted on metalsurfaces.  

After setting the time, the “Heating & Cooling Option” button needs to be pressed  

once. For minute setting, minute part will be blinking. You mayset the minute with  

the“+” and“-” buttons.  

The devices should not be installed close to electrical cables and electronic  

equipment such ascomputers and televisionunits.  

Temperature Measurement Accuracy  

Operating Temperature Range  

Battery Life  

RECEIVERLEDDESCRIPTIONS  

Steady Red  

Receiver has power but Receiver and  

Room Thermostat are not paired.  

Waiting for pairing signal from Room Thermostat.  

Receiver and Room Thermostat are paired.  

Boiler is not operating.  







The devices should not be installed near large metal structures or other building  

materialsusing finemetalmeshes such asspecialglass or specialconcrete.  

Distance between the Room Thermostat and the Receiver should not exceed 20  

metersor 2 floors.  

1 Years (2 x AAA)  

(-10^oC) – (+50^oC)  

(-20^oC) – (+60^oC)  



After setting the minute, the “Heating & Cooling Option” button needs to be  

pressedonce to setthedayof theweek.  

Operating Temperature  

Storage Temperature  

Blinking Green  

Steady Green  





Mondayhas setasthefirstdayof theweekand indicated withnumber“1".  

Numbers indicate the following days respectively 2-Tuesday, 3-Wednesday, 4-  

Thursday, 5-Friday, 6-Saturdayand 7-Sunday  

Receivermust be installed atleast50cmawayfromtheheating/cooling unit.  

Receiver  

3 Short Orange  

Blinking  

Operate the boiler signal has reached to the  

Receiver.  

Dimensions  

Operation Current  

Relay NO Switching Current  

90mm / 90mm / 25mm  

230V AC  



When setting is done, you may exit by pressing the “Weekly Program” button for 3  

seconds.  

RECEIVERSETUP  

Steady Orange  

3 Short Green  

Blinking  

Boiler is operating.  







First, shut down your heating/cooling unit and your heating/cooling unit's power  

sourcewithallelectricalcurrent(fuse, socketetc.)  

7A (240VAC – Resistive load)  

10A (120VAC – Resistive load)  

(-20^oC) – (+60^oC)  

Shut the boiler down signal has reached to the  

Receiver.  

MODESETTING  

As shown in the connection diagram, connect one end of the heating/cooling unit  

connection cabletotheCOMand theother to theNOinput of theReceiver.  

Connect the other ends of the cable -which youconnected to the Receiverto room  

thermostat connection terminal as shown in your heating/cooling unit's user  

manual.  

MODES  

Storage Temperature  

Blinking Orange  

Boiler is operating in manual mode.  

ROOMTHERMOSTAT  

Buttons Functions  

Blinking Red  

Receiver did not get a signal from the  

Room Thermostat for 22 minutes or longer and  

boiler has shut down.  

PRESET MODES  

WEEKLY  

PROGRAM  

MODE  

MANUAL MODE  







You must first connect the Receiver power cable to the Receiver and then to the  

fuse to which theheating/cooling unit is connected.  

Comfort  

Mode  

Economy  

Mode  

ROOMTHERMOSTATPLACEMENT  

After completing the cable connection process, firstly turn on your fuse and then  

yourheating/cooling unit.  

1

Room Thermostat needs to be placed in the room which is used most frequently.  

For instance; living room or lounge. Placing the Room Thermostat in a spot that  

have air circulation like entrance of a room or side of window should be avoided.  

Also anywhere close to heating/cooling units such as radiator, stove and spots  

which get direct sun lights would not be suitable. Room Thermostat needs to be  

located above the floor 150 cm height. Few trials may be made to find the most  

convenientspot.  

Your Room Thermostat has 4 different modes. 3 of them (Comfort and Economy  

Mode) are preset modes. Other modes are manual mode and weekly program  

mode.  

By pressing the Receiver's manual usage button for 2 seconds, you should see  

the Orange Light blinking on the Receiver. In this way, after making sure that the  

heating/cooling unit is operating, press the same button again for 2 seconds and  

seethattheOrange LEDturns off.  

2

3

In preset modes, temperature values are based on user's choices which have been  

set in the beginning. Manual mode allows the Room Thermostat to operate within  

the temperature which is required and set directly by user. Weekly Program mode  

continues toworkaccordingto theweeklyschedule determined bytheuser.  

In orderto change thetemperaturevaluesof presetmodes:  

4



Setup theRoom Thermostatto pair theReceiverwiththeRoom Thermostat.  

5

6

RECEIVERWIRINGDIAGRAM  

AC  

COM  

NO  

(230V)  







Press and hold the “Mode” button for 3 seconds while your Room Thermostat is  

on.  

1

2

3

4

5

6

ON/OFF Button  

Weekly Program Button  

Mode Button  

Comfort Mode temperature value will appear. You may adjust the temperature  

valueof Comfort Mode bypressingthe“+” and “-” buttons.  

When setting is done, you may adjust the temperature value of Economy Mode  

withthe“+” and “-” buttons bypressingthe“Mode”button again.  

You mayexitthesettingscreenbypressingthe“Mode”button 3 seconds.  

In order to change the manual mode temperature, press the “+” or “-” button while  

in the main screen. The Room Thermostat will switch to Manual Mode once  

pressedthe“+” or “-” button.  

Heating & Cooling Option  

Temperature Adjustment (Increasing)  

Temperature Adjustment (Decreasing)  





HEATING/COOLING UNIT  



You maypressthe“Mode”button to switchto theother modes.  

1

2

3

4

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	SENNA-300-RF Digital Room Thermostat User Guide
Make	SENNA
Language	English
Filetype	PDF (Download)
File size	2.21 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• SENNA

SENNA-300-RF Digital Room Thermostat User Guide Overview

Summary of Contents

• Page 1: Warning: Operations within the heating/cooling unit or the electrical installation must be carried out by professionally qualified persons. Digital room thermostat pairing instructions include pressing the sync button of the receiver for 2 seconds. If the pairing is successful, the green flashing LED on the receiver will be steady. Room temperature calibration may be necessary to align the thermostat with other thermometers in your living space. The room thermostat features daily and weekly programming options, including economy and comfort modes. Battery placement involves inserting 2 new AAA alkaline batteries in the correct direction. Low battery warning appears when the icon shows on the screen, indicating the need for battery replacement. Factory settings can be reset, which will restore mode temperature values and calibration settings to default. Receiver placement should avoid physical contact with heating/cooling units and protect against liquids and dust. The room thermostat should be placed in frequently used rooms, avoiding areas with direct sunlight or close proximity to heating/cooling units.
• Page 2: You may set the operating schedule of your room thermostat with a weekly program. The warranty period starts from the invoice date and is warranted against manufacturing defects for 5 years. Your room thermostat takes the average room temperature of the last 40 seconds as a basis. With the TPI algorithm, it learns how long it takes to reach the desired room temperature and how this temperature is maintained. Seven different temperature values can be set for each day in weekly programming. In order to set the weekly schedule, press and hold the “Weekly Program” button for 3 seconds while your room thermostat is on. If the placement of the TPI room thermostats is changed, the learning process will restart. Malfunctions resulting from the use of devices contrary to the user manual are not covered by the warranty. The customer can make complaints and appeals to consumer courts or consumer arbitration committees. The warranty document must be kept by the customer during the warranty period.