Regulus TP18 LCD Electronic Thermostat User Manual
Elektronický termostat TP18 LCD
TP18 LCD Electronic thermostat
Thermostat Location:
Vhodné umístění:
The thermostat is designed for interior use only. It
should be installed on an inner wall about 1.5 m
above the floor in a position where it is exposed to
temperature changes thanks to freely circulating
air. Do not install over hot surfaces (e.g. TV set,
heating, refrigerator), do not expose to direct
sunshine, draft, radiation from appliances, do not
install into a laundry. Do not expose the thermostat
to dripping / splashing water.
Termostat smí být používán pouze v interiéru. Měl
by být namontován na vnitřní stěně asi 1,5 m nad
podlahou v poloze, kde na něj působí změny
pokojové teploty díky volně cirkulujícímu vzduchu.
Nemontujte ho nad horký povrch (např. TV, topení,
lednice), nevystavujte ho přímému slunečnímu
záření, průvanu, záření z přístrojů, nemontujte ho
do prádelny. Nevystavujte ho kapající ani stříkající
vodě.
Návod k montáži:
1. Montáž termostatu:
Installation:
1. Thermostat mounting:
-
Umístěte kabely do otvoru u svorkovnice
(na zadní stěně termostatu).
-
Route the wires through the hole at the
terminal block (thermostat's rear side).
Attach the thermostat to the wall with the
enclosed dowels and screws.
-
Pomocí přiložených hmoždinek
a
vrutů
-
připevněte termostat na zeď.
2. Electric wiring
Connect the appropriate wires into the terminal block as shown
in the wiring drawing inside the cover.
-
2. Elektrické zapojení
-
Připojte příslušné kabely do svorkovnice podle výkresu
zapojení v krytu.
3. Temperature setting
3. Nastavení teploty
-
Select the desired temperature by pressing
or . During temperature adjusting, the
-
Pomocí tlačítek
na displeji zobrazován symbol
8 sec. po ukončení nastavování se displej vrátí k zobrazení pokojové teploty a symbol ruky zmizí.
Stav termostatu indikuje symbol teploměru. Pokud je termostat sepnutý („topení topí“),
symbol teploměru na displeji bliká.
nebo zvolte požadovanou teplotu . Po dobu nastavování teploty je
a požadovaná teplota.
symbol and the desired temperature are shown on the display.
8 sec. after temperature setting the display returns to room temperature and the hand symbol
disappears.
The thermostat status is indicated by a thermometer symbol. If the thermostat is closed
("heating active“), the thermometer symbol is blinking on the display.
-
-
-
-
4. Jumper selection (normally set to heating)
4. Volba jumperu (normálně nastaveno topení)
-
By the jumper either heating (Heater), or cooling (Cooler) function can be selected.
If the jumper is not fitted, the thermostat will not work.
-
Pomocí jumperu lze zvolit funkci topení (Heater), nebo funkci chlazení (Cooler).
Pokud nebude jumper nasazen, termostat nebude fungovat.
-
-
5. Battery installation/replacement
5. Instalace / výměna baterie
Use only identical or equivalent type of batteries. Do not dispose of batteries with regular
household trash.
Použijte pouze stejný nebo ekvivalentní typ baterií. Nevyhazujte baterie do domovního odpadu.
Technické údaje:
Technical data:
Teplotní rozsah:
Spínací diference:
Napájení:
Jmenovité zatížení kontaktů:
Čidlo:
Časová konstanta:
Provozní teplota:
Teplota skladování:
5 až 35°C nastavitelný
cca 0,5°C
2 x baterie AAA
24…250 VAC 5(3,5)A
NTC termistor
cca 2 min.
Temperature range:
Switching difference:
Power supply:
Nominal contacts rating:
Probe:
Time constant:
Operating temperature:
Storing temperature:
5 to 35°C adjustable
about 0,5°C
2 AAA batteries
24…250 VAC 5(3,5)A
NTC thermistor
about 2 min.
0 až 45°C
-10 až 55°C
0 to 45°C
-10 to 55°C
General | Details |
---|---|
Name | Regulus TP18 LCD Electronic Thermostat User Manual |
Make | Regulus |
Language | English |
Filetype | PDF (Download) |
File size | 0.13 MB |

Regulus TZT 63 Electronic Plug-In Thermostat User Guide
