Honeywell TH1100DH Non Programmable Thermostat Instruction Manual

1

2

PRO 1000 Series  

Non-Progammable Thermostat  

*

Cool  

On  

Product Information  

TH1100DH: For 1 Heat systems  

Fan  

Auto On  

TH1110DH: For 1 Heat/1 Cool systems  

TH1110E: For 1 Heat/1 Cool systems  

Heat Off Cool  

*TH1110E model has a larger display than pictured  

TH1210DH: For 2 Heat/1 Cool heat pump systems  

Read before installing  

Quick reference to controls  

Built-in compressor protection  

This feature helps prevent damage to the  

compressor in your air conditioning or heat  

pump system.  

Up/Down buttons  

Press to adjust temperature.  

^Set 77  

^Set 77  

Damage can occur if the compressor is restarted  

too soon after shutdown. This feature forces the  

compressor to wait 5 minutes before restarting.  

Cool  

On  

Fan Switch  

Cool  

On  

On: Fan runs continuously.  

Auto: Fan runs only when heating  

or cooling system is on.  

During the wait time, the display will flash the  

message Cool On. When the safe wait time has  

elapsed, the message stops flashing and the  

compressor turns on.  

M32769  

Fan  

Auto On  

E.M. Heat Heat Off Cool  

Message flashes until  

safe restart time has  

elapsed.  

M32821  

System switch  

•

•

•

•

Cool: Cooling system control.  

Off: All systems off.  

CAUTION  

Equipment damage hazard  

To prevent possible compressor damage, do not operate cooling system  

when outdoor temperature is below 50°F (10°C).  

Heat: Heating system control.  

Em Heat: Emergency & Auxiliary Heat control. Compressor is locked  

out. (Select models only.)  

Battery replacement  

Quick reference to display screen  

Setpoint indicator  

Appears when the setpoint  

temperature is displayed  

Temperature  

Turn thermostat over, insert  

fresh AAA alkaline batteries,  

then reinstall thermostat.  

^Set 77  

Batt  

The ambient (measured)  

temperature is normally  

displayed. To view the  

RTHXXXX  

W/  

Not  

Aux Used  

System status  

setpoint temperature, press  

the Up or Down button once.  

The setpoint temperature  

will appear for five seconds.  

Cool on: Cooling system is on.  

Heat on: Heating system is on.  

Aux On: Auxiliary heat is on.  

(Only for heat pumps with  

this capability [select models  

only].)  

M32707  

Cool  

On  

Lo  

Install two fresh AAA batteries when Lo Batt  

flashes on the screen. Lo Batt appears for  

60 days before the batteries are depleted.  

Low battery warning  

Fan  

Auto On  

E.M. Heat Heat Off Cool  

M32823  

Replace batteries once a year, or when you  

will be away for more than a month.  

When “Heat On” or “Cool  

On” is flashing, compressor  

protection is engaged.  

Pull at bottom to  

remove thermostat  

from wallplate.  

The settings are stored in non-volatile  

(permanent) memory and are thus  

preserved when the thermostat is without  

batteries.  

Adjust the temperature  

Press s or t to adjust the  

temperature.  

Product manuals  

Search online for Resideo 69-2607EFS for the User Guide.  

Note: Make sure the thermostat  

is set to the system you want to  

control (heat or cool).  

Set  

77  

Cool  

On  

Electrical ratings  

System  

Voltage (50/60Hz)  

Running Current  

Fan  

Auto On  

E.M. Heat Heat Off Cool  

M32822  

Heat (1st stage)  

(Powerpile)  

Auxiliary heat  

Cooling  

20-30 Vac  

750 mV DC  

20-30 Vac  

20-30 Vac  

0.02-1.0 A  

100 mA DC  

0.02-1.0 A  

0.02-1.0 A  

Need Help?  

For assistance please visit  

Resideo.com  

33-00529EFS-03  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	Honeywell TH1100DH Non Programmable Thermostat Instruction Manual
Make	Honeywell
Language	English
Filetype	PDF (Download)
File size	0.11 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• Honeywell

Honeywell TH1100DH Non Programmable Thermostat Instruction Manual Overview

Summary of Contents

• Page 1: PRO 1000 Series Non-programmable thermostat Product information Read before installing Built-in compressor protection This feature helps prevent damage to the compressor in your air conditioning or heat pump system. Damage can occur if the compressor is restarted too soon after shutdown. CAUTION: Equipment damage hazard To prevent possible compressor damage, do not operate cooling system when outdoor temperature is below 50°F (10°C). Battery replacement Low battery warning The settings are stored in non-volatile memory and are thus preserved when the thermostat is without batteries.
• Page 2: In case of difficulty If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily. Display is blank Check circuit breaker and reset if necessary. Make sure power switch at heating & cooling system is on. Make sure furnace door is closed securely. Make sure fresh AAA alkaline batteries are correctly installed. Heating or cooling system does not respond Set system switch to Heat. Make sure the temperature is set higher than the Inside temperature. Set system switch to Cool. Make sure the temperature is set lower than the Inside temperature. Wait 5 minutes for the system to respond. “Heat On” or “Cool On” is flashing Compressor protection feature is engaged. Wait 5 minutes for the system to restart safely, without damage to the compressor. “Heat On” is not displayed Set the System switch to Heat, and set the temperature level above the current room temperature. “Cool On” is not displayed Set the System switch to Cool, and set the temperature level below the current room temperature.