GENERAL LIFE Senna 270S RF Wireless Room Thermostat User Manual

1

2

ScreenIndicators  

RECEIVER WIRING DIAGRAM  

ENGLISH  

AC  

COM  

NO  

(230V)  

5

DIGITAL ROOM THERMOSTAT  

6

7

1

2

generallife.com.tr  

BATTERY PLACEMENT  

3

4

SENNA 270 RF USER MANUAL  

HEATING/COOLING UNIT  

GENERAL SPECIFICATIONS  

1

2

3

4

5

Room Temperature  

SENNA270RFis awirelessroom thermostat. The user can adjust the  

room temperaturewiththerequired temperatureand getmore  

comfortable and economic heating/cooling.  

Warning!  

Operations within the heating / cooling unit or the electrical installation  

must be carriedout byprofessionally qualified persons.  

Set Temperature  

Economy Mode  

Comfort Mode  

Battery Indicator  

Heating Indicator  

- If the Heating Indicator is blinking, the heating unit is working.  

- If the Heating Indicator is steady, the heating unit is not working.  

Cooling Indicator  

- If the Cooling Indicator is blinking, the cooling unit is working.  

- If the Cooling Indicator is steady, the cooling unit is not working.  

 Different Mode Options (Comfort Mode and Economy Mode)  

PAIRING THE ROOM THERMOSTAT AND THE RECEIVER  

 PreciseTemperatureMeasurement  

 Heating Calibration  

ON/OFFControl  

WirelessConnection  

TPIAlgorithm  

6

7



Primarily press the sync button of receiver for 2 seconds and see blinking  

green light of receiver.  

 Heating/Cooling Modes  



While your device is turned off, press and hold the "On/Off"button for 3  

seconds.  

As shown in the picture above, press the screwdriverforward from the space  

shown, bend the tabs and separate the front cover. Insert 2 new AAA alkaline  

batteries in the battery housing with the correct battery direction. Replace  

both batteries at the same time. Then align the front part of your Room  

Thermostatto the backand squeezeittowards theback.  

SENNA 270 RF AND EQUIPMENTS  





Press thebutton until the “  

” menu appears.  

SENNA 270 RF Room Thermostat  

Holder  

Alkaline  

Battery  

Press the "+" or "-" button of your Room Thermostat while the LED is  

flashing green.  

RECEIVER  

1-Manual Operation Button:  

By disabling the Receiver, it enables you to  

use your boiler manually.  





If the pairing is successful, the green flashing LED on the receiver will be  

constant.  

1

2

3

Low Battery Warning: When the “  

” icon appears on the screen, it means  

“low battery warning”. It is recommended to replace the batteries when this  

warning appears.  

Receiverand Room Thermostathavebeen paired to each other.  

2-Pairing Button:  

Allows to pair the Receiver with the Room  

Thermostat.  

3-Receiver LED Light  

4-Receiver Power Cable Input  

5-Boiler Connection Cable Input  

Dowels and Screws  

Receiver  

Warning: When the product is not used for a long period (more than 15 days),  

remove the batteries. Otherwise, malfunctions that may occur would be out of  

warranty.  

ROOM THERMOSTATTEMPERATURE CALIBRATION  

Temperature sensors which are used in Room Thermostats are highly  

sensitive. You mayneed to calibrate yourRoom Thermostat if youwould like  

to get the same temperature values with other thermometers in your living  

space.  

Please throwyour dead batteries into thewaste bin forbatteries.  

RECEIVER PLACEMENT  



While your device is turned off, press and hold the "On/Off"button for 3  

seconds.  

4 5  

RECEIVER LED DESCRIPTIONS  

The important things to note for the Receiver  

placement is avoiding physical contact between the  

Receiver and heating/cooling unit, and protecting it  

against materialssuch asliquid, dust etc.  



Press the "On/Off" button until the “  

” menu appers. In order to see the  

TECHNICAL DATA  

Room Thermostat  

desired temperature, set the temperature difference by press the  

“Temperature Adjustment Buttons”. This value can be arranged between  

“-8^oC" and “+8^oC".  

Dimensions  

Operating Current  

85mm / 125mm / 19mm  

3V DC (2 x AAA alkaline battery)  

Steady Red  

Receiver has power but Receiver and  

Room Thermostat are not paired.  

Waiting for pairing signal from Room Thermostat.  

Receiver and Room Thermostat are paired.  

Boiler is not operating.  



To save the settings and exit, press the "On/Off" button until the device  

turns off.  

Temperature Measurement Accuracy 0.1^oC  

Blinking Green  

Steady Green  

Operating Temperature Range  

Battery Life  

Operating Temperature  

Storage Temperature  

(5^oC) – (30^oC)  

1 Years (2 x AAA)  

(-10^oC) – (+50^oC)  

(-20^oC) – (+60^oC)  

The devices should be placed in order to minimize the damage to the  

receivedand transmittedsignals bypayingattentiontothefollowingpoints;  

Note:Recommended tempreturecalibration is “0.0^oC”.  





The devicesshould not be mounted on metalsurfaces.  

The devices should not be installed close to electrical cables and  

electronic equipment such ascomputers and televisionunits.  

The devices should not be installed near large metal structures or other  

building materials using fine metal meshes such as special glass or  

special concrete.  

3 Short Orange  

Blinking  

Operate the boiler signal has reached to the  

Receiver.  

FACTORY SETTINGS RESET  

You can reset your Room Thermostat to its default factory settings. This  

operation resets the mode temperature values, calibration setting and  

heating/coling modes to factory setting. To reset your Room Thermostat to  

factory setting:  

Steady Orange  

3 Short Green  

Blinking  

Boiler is operating.  

Shut the boiler down signal has reached to the  

Receiver.  

Receiver  



Dimensions  

Operation Current  

Relay NO Switching Current  

90mm / 90mm / 25mm  

230V AC  

7A (240VAC – Resistive load)  

10A (120VAC – Resistive load)  

(-20^oC) – (+60^oC)  

Blinking Orange  

Boiler is operating in manual mode.  



While your device is turned off, press and hold the "On/Off"button for 3  

seconds.  





Distance between the Room Thermostat and the Receiver should not  

exceed 20metersor 2 floors.  

Blinking Red  

Receiver did not get a signal from the  

Room Thermostat for 22 minutes or longer and  

boiler has shut down.  

Storage Temperature  





Pressthe“On/Off” button until “  

” menu appears.  

Receiver must be installed at least 50 cm away from the heating/cooling  

unit.  

While in the “ ” menu, select the “ ” option by using “+” or “-” buttons  

ROOM THERMOSTAT  

Buttons Functions  

and press the“On/Off” button.  

ROOM THERMOSTAT PLACEMENT  



Your devicewill be turned off and resetto factory settings.  

RECEIVER SETUP  

Room Thermostat needs to be placed in the room which is used most  

frequently. For instance; living room or lounge. Placing the Room  

Thermostat in a spot that have air circulation like entrance of a room or side  

of window should be avoided. Also anywhere close to heating/cooling units  

such as radiator, stove and spots which get direct sun lights would not be  

suitable. Room Thermostat needs to be located above the floor 150 cm  

height. Fewtrialsmaybe made to find themost convenientspot.  



First, shut down your heating/cooling unit and your heating/cooling unit's  

power sourcewithall electricalcurrent(fuse, socketetc.)  

As shown in the connection diagram, connect one end of the  

heating/cooling unit connection cable to the COM and the other to the NO  

input of theReceiver.  

MODE SETTINGS  

There are 2 modes in the Room Thermostat. These are Comfort Mode “  

1

”



and Economy Mode “ ”. Modes work according to the pre-set temperature  

valuesadjusted byuser.  

2

3

In order to change the comfort mode temperaturevalue;  



Connect the other ends of the cable -which you connected to the Receiver  

to room thermostat connection terminal as shown in your  

heating/cooling unit's user manual.  

4







Press and hold thecomfort mode button for 3 seconds.  

Change the temperaturevaluebypressing “+” or “-“ buttons.  

Press the comfort mode button once to save the changes you have made  

or wait10seconds.  







You must first connect the Receiver power cable to the Receiver and then  

to thefuse to which theheating/cooling unit is connected.  

After completing the cable connection process, firstly turn on your fuse  

and then yourheating/cooling unit.  

5

6

In order to change theeconomy mode temperature value;  

1

2

3

4

5

6

ON/OFF and Setting Button  

Economy Mode  

Comfort Mode  

Heating/Cooling Modes  

Temperature Adjustment (Increasing)  

Temperature Adjustment (Decreasing)  







Pressand hold theeconomy mode button for 3 seconds.  

Change thetemperaturevaluebypressing “+” or “-” buttons.  

Press the economy mode button once to savethe changes youhavemade  

or wait10seconds.  

By pressing the Receiver's manual usage button for 2 seconds, youshould  

see the Orange Light blinking on the Receiver. In this way, after making  

sure that the heating/cooling unit is operating, press the same button  

again for 2 seconds and seethattheOrange LEDturns off.  

Set up the Room Thermostat to pair the Receiver with the Room  

Thermostat.  

You can use the “+” and “-” buttons to use the Room Thermostatmanually.  



1

2

3

4

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	GENERAL LIFE Senna 270S RF Wireless Room Thermostat User Manual
Make	GENERAL LIFE
Language	English
Filetype	PDF (Download)
File size	2.23 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• GENERAL LIFE

GENERAL LIFE Senna 270S RF Wireless Room Thermostat User Manual Overview

Summary of Contents

• Page 1: Receiver wiring diagram Digital room thermostat SENNA 270 RF is a wireless room thermostat. The user can adjust the room temperature with the required temperature and get more comfortable and economic heating/cooling. Warning! Operations within the heating/cooling unit or the electrical installation must be carried out by professionally qualified persons. Different mode options (Comfort Mode and Economy Mode) Low battery warning: When the icon appears on the screen, it means “low battery warning”. Temperature sensors used in room thermostats are highly sensitive. You may need to calibrate your room thermostat if you would like to get the same temperature values with other thermometers in your living space. Receiver must be installed at least 50 cm away from the heating/cooling unit. Room thermostat needs to be placed in the room which is used most frequently. There are 2 modes in the room thermostat: Comfort Mode and Economy Mode.
• Page 2: Warranty conditions outline the coverage for manufacturing defects for 5 years from the invoice date. The room thermostat operates using TPI technology, which helps maintain the desired temperature with minimal fluctuations. If the thermostat loses connection with the receiver for 22 minutes, it will stop heating or cooling for safety. The warranty covers repairs conducted at the company factory, with transportation costs borne by the customer. Malfunctions caused by customer misuse or external factors are not covered by the warranty. The learning process for TPI thermostats restarts if the device is de-energized or relocated. The thermostat's compatibility with heating/cooling units is confirmed if they have On-Off connections. Customers must report any product damages within the warranty period to maintain their rights. The warranty document must be retained by the customer; a replacement will incur a fee if lost. The manufacturer reserves the right to change product specifications and user manuals.