Home > e l m leblanc > e l m leblanc TRL 7.26 RF Room Thermostat User Manual
e l m leblanc TRL 7.26 RF Room Thermostat User Manual
Machine Translated by Google
Using the Receiver
8 Using the receiver
9 Radio configuration of the TRL with the receiver
tor
ÿ On the TRL, select the "Auto" mode.
ÿ Then press the OK button for 5 seconds; this will enter the radio
1
configuration mode ( ).
4
The TRL now sends its configuration address by radio signal 4 times
per second, ÿ On the receiver, press the button for 5 seconds.
2
3
0 010 007 232-001
Fig. 8
The green LED [4] should light up and start flashing with each radio
signal received from the TRL (4 flashes per second). ÿ You can now
perform a dis check
[1]
Key: pressing for 5 seconds gives access to the radio
configuration of the receiver (ÿ page 7)
[2]
Receiver power-on indication
Operation mode indication
radio operating time.
[3, 4]
Place the TRL in the room where you want to regulate the temperature
and leave it in radio configuration mode ( ).
Functioning
[2] [3]
[4]
Yellow Red Green
ÿ Close the doors and return to the receiver. ÿ Check
0
1
1
1
0
0
1
0
0
0
Receiver not powered
HEATING mode off
that the green LED [4] flashes with each signal
radio :
HEAT mode on
– If it flashes several times per second, the installation of the TRL and
the receiver is correct.
0 or 1 Flash
0 or 1 1
Receipt of an order, 4 quick
flashes
– If it flashes irregularly, you are at the range limit. Install the TRL closer
to the receiver.
1
Waiting for the configuration signal
(ÿ radio configuration of the TRL
with the receiver, page 7)
– If there is no flashing, you are out of range. Install the TRL closer to
the receiver. ÿ On the TRL press the OK key to exit the radio
configuration mode.
1
0
Slow
ERROR see troubleshooting
below
flashing
Now the TRL drives the receiver.
0
0 or Cli
Transmitter in OFF mode.
Cligno
slow fear
slow gnosis
Flashing green LED indicates
reception of a frame from the
transmitter
Troubleshooting
ÿ Check the batteries of the transmitter. ÿ
Check transmitter/receiver range. ÿ Check that
there is no interference from another device less than 50 cm from the
receiver. ÿ Check that there is no interference from a device on the
868.3 MHz frequency (permanent emission).
If the yellow LED [2] does not light up: ÿ Check
the connection of the receiver. ÿ Check the mains
supply (230 VAC).
7
TRL 7.26 RF – 6720816708 (2015/05)
| General | Details |
|---|---|
| Name | e l m leblanc TRL 7.26 RF Room Thermostat User Manual |
| Make | e l m leblanc |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.15 MB |
(1 votes, average: 5.00 out of 5)
Loading...
WIFI Temp2 Battery Operated Thermostat Installation Guide
Drayton 2290M Digistat 3rd Generation Programmable Room Thermostat Installation Guide
BOSCH II 230V Room Thermostat Instruction Manual
GENERAL LIFE ARUNA 302S Smart Room Thermostat User Manual
BeSMART 20143539 WiFi Smartphone Thermostat with Backlight User Guide
Rheem RETST700SYS EcoNet Smart Thermostat Owner’s Manual
Beca BHT-8000 Heating Thermostat User Guide
hansgrohe 15754000 Metris Classic Ecostat Classic High Flow Thermostat Instruction Manual
Honeywell TH5000 Series FocusPRO Non-Programmable Digital Thermostat Installation Guide
JUNG RTR230 230V Room Thermostat User Manual