Danfoss Heating Solutions WT-T BasicPlus2 Room Thermostat Installation Guide

1

2

3

4

5

6

7

8

Installation Guide  

BasicPlus² WT-T  

Room thermostat  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	Danfoss Heating Solutions WT-T BasicPlus2 Room Thermostat Installation Guide
Make	Danfoss Heating Solutions
Language	English
Filetype	PDF (Download)
File size	0.09 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL THERMOSTAT INSTRUCTIONS & USER MANUALS
• Danfoss Heating Solutions

Danfoss Heating Solutions WT-T BasicPlus2 Room Thermostat Installation Guide Overview

Summary of Contents

• Page 1: Installation guide for BasicPlus WT-T room thermostat.
• Page 2: Installation must be done by an authorised electrician. The room thermostat should be installed at approx. 1.5 m above floor and where the effects of sunlight, draught or other heat sources are avoided. Carefully remove the cover and dial knob before installation. Connect the wire before mounting the back plate to the wallbox using the enclosed screws. WT-T is often used with a Danfoss TWA actuator. Wiring between room thermostat and actuator is different depending on power location and actuator type. Follow the illustrations to complete the wiring. Connect to actuator TWA 230 V NC type or NO type based on power supply location. Refer to figures for dimensions and wiring diagrams. Ensure proper connections based on the conditions of power location and actuator type.
• Page 3: Installation guide for BasicPlus WT-T room thermostat includes essential notes for correct wiring and installation. Correct wiring is essential; using an instrument to confirm L and N before wiring is recommended. Avoid removing too much insulation from the wire to prevent short circuits. Ensure screws do not touch the wire when fixing the thermostat in the wall box to reduce short-circuit risks. If walls need painting, install the thermostat after painting to prevent damage from dust or paint. The maximum load of the relay is 3 A (resistive) or 1 A (inductive); exceeding this limit can damage the relay. Do not cover the thermostat with items like towels. The thermostat should connect to the corresponding loop actuator for individual room temperature control.
• Page 4: Installation guide for the BasicPlus WT-T room thermostat includes technical specifications. The CE marking complies with EN60730 standards. The ambient temperature range is from -10 to 60° C. The IP class rating is 30. The maximum load for inductive is less than 1 A. The maximum load for resistive is less than 3 A. Power consumption is 7 W. The power supply is 230 Vac with a tolerance of 10%, operating at 50/60 Hz. The room temperature set range is between 5 and 30° C. The shell material is made of ABS + PC.
• Page 5: Installation guide for BasicPlus. Illustrations of WT-T. Figures 1, 2, and 3 are included. Danfoss Heating Solutions is mentioned. Model number VICUL212 is referenced.
• Page 6: Installation guide for BasicPlus. Illustrations of WT-T. Figures 4, 5, and 6 are included. Electrical specifications include 230 V ~. Connections for L, N, NO, and NC are indicated. Danfoss Heating Solutions is mentioned.
• Page 7: Installation guide for BasicPlus. Illustrations of WT-T. 230V configurations for NO and NC connections. Danfoss Heating Solutions.
• Page 8: Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved. Produced by Danfoss Floor Heating Hydronics 03/2015.